by both OLDCARD and NEWCARD.
# didn't make the tables the same because oldcard supports more devices than
# newcard and newcard's 16-bit stuff needs some work.
the built-in 1000baseX interface in the Level 1 LXT1001 chip. The Level 1
PHY comes up with the isolate bit in the control register set by default,
but it also has the autonegotiate bit set. When you tell the xmphy driver
to select IFM_AUTO mode, it sees that the autoneg bit is already on, and
thus doesn't bother updating the control register. However this means that
the isolate bit is never turned off (unless you manually select 1000baseSX
full or half duplex mode, which does result in the control register being
modified and the ISO bit being turned off).
This subtle and unusual behavioral difference stopped me from being able
to receive packets on the SMC9462TX card for several days, since isolating
the PHY disconnects it from the MAC's data interface. The fix is to omit
the 'is the autoneg big set?' test, since it doesn't really provide much
of an optimization anyway.
This commit also updates the xmphy driver to support the Jato/Level 1
internal PHY. (I'm not sure how Jato Technologies is related to Level 1:
all I know is the OUI from the PHY ID registers maps to Jato in the OUI
database.) This will be used once I add the if_lge driver to support
the LXT10010 chip.
requiring fewer header files for userland programs.
Remove the gross debug device/non-debug device hack used to recognize
whether the kernel module was in sync with the userland module.
compiled with debug support. This can be used by userland programs to
recognize which ioctls the module supports.
As a result, remove the gross debug device/non-debug device hack used
to recognize whether the kernel module was in sync with the userland
module.
Replace explicit references to major/minor numbers of vinum
superdevice with the VINUM_SUPERDEV macro written for that purpose.
needs instead of relying on idiosyncratic hacks in the tty subsystem.
Also add module code since this can now be compiled as a module.
Silence by: -hackers, -audit
gets incremented every time the kernel-userland interface changes.
This enables vinum(8) to check for the correct kernel version and to
produce a useful message if it doesn't match.
Requested by: Too many to count.
Move the definitions of struct drive, sd, plex and volume to
vinumobj.h.
Add a new debug flag, DEBUG_LOCKREQS, which logs only lock requests.
with more than one plex, the data will be accessed
multiple times. During this time, userland code could
potentially modify the buffer, thus causing data
corruption. In the case of a multi-plexed volume this
might be cosmetic, but in the case of a RAID-[45] plex it
can cause severe data corruption which only becomes
evident after a drive failure. Avoid this situation by
making a copy of the data buffer before using it.
Note that this solution does not guarantee any particular
content of the buffer, just that it remains unchanged for
the duration of the request.
Suggested by: alfred
Use this instead of DEBUG_LASTREQS to decide whether to log lock
requests.
MFS:
vinumlock: Catch a potential race condition where one process is
waiting for a lock, and between the time it is woken and
it retries the lock, another process gets it and places it
in the first entry in the table.
This problem has not been observed, but it's possible, and
it's easy enough to fix.
Submitted by: tegge
vinumunlock: Catch a real bug capable of hanging a system. When
releasing a lock, vinumunlock() called wakeup_one. This
caused wakeups to sometimes get lost. After due
consideration, we think that this is due to the fact that
you can't guarantee that some other process is also
waiting on the same address. This makes wakeup_one a
very dangerous function to use.
Requested by: bde
Add retryerrors keyword.
vinum_scandisk: Print a different message if an inadvertent start
command did not find any additional drives. The previous message "no
drives found" confused and worried many people.
MFS:
vinum_open: Recognize Mylex devices as storage devices.
In case of error, check the VF_RETRYERRORS flag in the subdisk and
don't take the subdisk down if it's set, just retry the I/O.
Requested by: peter
If the buffer has been copied (XFR_COPYBUF), release the copied
buffer when the I/O completes.
Suggested by: alfred
Desired by: bde
This commit is the first of a general cleanup of the header files..
It won't be enough to make bde happy.
Move debug definitions from vinumhdr.h.
Create a new struct rangelockinfo. In revision 1.21 of vinumlock.c,
the plex info was removed from struct rangelock, since it wasn't
needed there. It *is* needed for trace information, however, so use
struct rangelockinfo for that.
vm_mtx does not recurse and is required for most low level
vm operations.
faults can not be taken without holding Giant.
Memory subsystems can now call the base page allocators safely.
Almost all atomic ops were removed as they are covered under the
vm mutex.
Alpha and ia64 now need to catch up to i386's trap handlers.
FFS and NFS have been tested, other filesystems will need minor
changes (grabbing the vm lock when twiddling page properties).
Reviewed (partially) by: jake, jhb
copies out the current contents of the video buffer for a syscons terminal,
providing a snapshot of the text and attributes.
Based heavily on work originally submitted by Joel Holveck <joelh@gnu.org>
for 2.2.x almost 30 months ago, which I cleaned up a little, and forward
ported to -current.
See also the usr.bin/scrshot utility.
Pro and Raylink cards with version 5 firmware. Only infra-structure
mode has been tested. Specific changes for this feature are:
o Add RFC1042 encapsulation of IP datagrams
o Add authentication and association
o Decode of the beacon (although not used)
Other changes have been made:
o Pass command completion status to *_done (in place for
adding proper error recovery)
o Move a couple of state variables into the current
network parameters structure. This is in prep. for
dealing with roaming.
MFC after: 1 week
be unions with enough padding to make sure they always end up being
a multiple of 8 bytes in size, since the 83820/83821 chips require
descriptors to be aligned on 64-bit boundaries. I happened to get it
right for the 32-bit descriptor/x86 case, but botched everything else.
Things should work properle on 32-bit/64-bit platforms now.
Note that the 64-bit descriptor format isn't being used currently.
ahc_pci.c:
Prepare for making ahc a module by adding module dependency
and version info.
aic7770.c:
Remove linux header ifdefs. The headers are handled differently
in Linux where local includes (those using "'s instead of <>'s)
are allowed.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
aic7xxx.c:
Remove linux header ifdefs.
current->curr to avoid Linux's use of current as a
#define for the current task on some architectures.
Add a helper function, ahc_assert_atn(), for use in
message phases we handle manually. This hides the fact
that U160 chips with the expected phase matching disabled
need to have SCSISIGO updated differently.
if (ahc_check_residual(scb) != 0)
ahc_calc_residual(scb);
else
ahc_set_residual(scb, 0);
becomes:
ahc_update_residual(scb);
Modify scsi parity error (or CRC error) handling to
reflect expected phase being disabled on U160 chips.
Move SELTO handling above BUSFREE handling so we can
use the new busfree interrupt behavior on U160 chips.
In ahc_build_transfer_msg() filter the period and ppr_options
prior to deciding whether a PPR message is required.
ppr_options may be forced to zero which will effect our
decision.
Correct a long standing but latent bug in ahc_find_syncrate().
We could choose a DT only rate even though DT transfers were
disabled. In the CAM environment this was unlikely as CAM
filters our rate to a non-DT value if the device does not
support such rates.
When displaing controller characteristics, include the
speed of the chip. This way we can modify the transfer
speed based on optional features that are enabled/disabled
in a particular application.
Add support for switching from fully blown tagged queing
to just using simple queue tags should the device reject
an ordered tag.
Remove per-target "current" disconnect and tag queuing
enable flags. These should be per-device and are not
referenced internally be the driver, so we let the OSM
track this state if it needs to.
Use SCSI-3 message terminology.
aic7xxx.h:
The real 7850 does not support Ultra modes, but there are
several cards that use the generic 7850 PCI ID even though
they are using an Ultra capable chip (7859/7860). We start
out with the AHC_ULTRA feature set and then check the
DEVSTATUS register to determine if the capability is really
present.
current -> curr
ahc_calc_residual() is no longer static allowing it to
be called from ahc_update_residual() in aic7xxx_inline.h.
Update some serial eeprom definitions for the latest
BIOS versions.
aic7xxx.reg:
Add a combined DATA_PHASE mask to the SCSIPHASE register
definition to simplify some sequencer code.
aic7xxx.seq:
Take advantage of some performance features available only
on the U160 chips. The auto-ack feature allows us to ack
data-in phases up to the data-fifo size while the sequencer
is still setting up the DMA engine. This greatly reduces
read transfer latency and simplifies testing for transfer
complete (check SCSIEN only). We also disable the expected
phase feature, and enable the new bus free interrupt behavior,
to avoid a few instructions.
Re-arrange the Ultra2+ data phase handling to allow us to
do more work in parallel with the data fifo flushing on a
read.
On an SDTR, ack the message immediately so the target can
prepare the next phase or message byte in parallel with
our work to honor the message.
aic7xxx_93cx6.c:
Remove linux header ifdefs.
aic7xxx_freebsd.c:
current -> curr
Add a module event handler.
Handle tag downgrades in our ahc_send_async() handler.
We won't be able to downgrade to "basic queuing" until
CAM is made aware of this queuing type.
aic7xxx_freebsd.h:
Include cleanups.
Define offsetof if required.
Correct a few comments.
Update prototype of ahc_send_async().
aic7xxx_inline.h:
Implement ahc_update_residual().
aic7xxx_pci.c:
Remove linux header ifdefs.
Correct a few product strings.
Enable several U160 performance enhancing features.
Modify Ultra capability determination so we will enable
Ultra speeds on devices with a 7850 PCI id that happen
to really be a 7859 or 7860.
Don't map our interrupt until after we are fully setup to
handle interrupts. Our interrupt line may be shared so
an interrupt could occur at any time.
of " &= ". Also change the MII PHY device mask to check the correct bits.
Cookie to: Andre Albsmeier <andre.albsmeier@mchp.siemens.de>
Pointy hat to: me
. FD_CLRERR clears the error counter, thus re-enables kernel error
printf()s,
. FD_GSTAT obtains the last FDC operation state, if any,
. FDOPT_NOERRLOG (temporarily) turns off kernel printf() floppy
error logging,
. FDOPT_NOERROR makes the kernel ignore an FDC error, thus can
enable the transfer of an erroneous sector to the user application
All options are being cleared on (last) close.
Prime consumer of the last features will be fdread(1), to be committed
shortly.
(FD_CLRERR should be wired into fdcontrol(8), but then fdcontrol(8)
needs a major rewrite anyway.)
