environments.
In setups where NF calibration can take a while, don't load the CCA
and kick off a new NF calibration if the previous one hasn't yet
completed. This shouldn't happen unless the environment is noisy but
those exist (hi phk!).
Here, if the previous NF hasn't completed when ar5416LoadNf() is run
(which reads the NF), it skips updating the history buffer, loading
the NF CCA array and kicking off the next NF cal. It's hoped it'll
occur in the next long calibration interval.
Obtained from: Atheros, ath9k, my local HAL
This is taking quite a while for some people in some situations
(eg AR5418 in phk's Abusive Radio Environment).
Instead, the rest of the calibration related code should
ensure that a NF calibration has occured before reading NF
values and kicking off another NF calibration.
The channel should also likely be marked as "noisy" (CWINT)
if the NF calibration takes too long.
CPU. This fixes a panic observed on Heathrow-based systems without
SMP-capable PICs when the kernel had both options SMP and INVARIANTS.
MFC after: 5 days
* Correct some of the silicon revision checks to match what
the Atheros HAL does. (See [1] below.)
* Move the PA cal and init cal method assignment to -after-
the mac version/revision IDs are stored. The AR9285 init
cal was never being called.
* Enable ANI.
Note Kite 1.0 and 1.1 were prototypes that shouldn't be seen
in the wild. Linux ath9k simply removed the prototype code from
their codebase. I'm going to leave it in there for now but
make it conditionally compilable in the future.
Obtained from: Atheros
newer controllers. However, all data sheet I have access has no
indication that buffer manager should not be touched on these
controllers. It seems the buffer manager always runs on BCM5705 or
newer controllers. Some controller(e.g. BCM5719) needs other buffer
manager configuration so driver should enable buffer manager for
all controllers. Both Linux and OpenBSD/NetBSD use the same
approach.
This change polls enable bit of block to know whether specified
block was really stopped as well as enabling buffer manager for all
controllers in driver initialization.
Obtained from: NetBSD
when the user has indicated that the system has synchronized TSCs or it has
P-state invariant TSCs. For the former case, we may clear the tunable if it
fails the test to prevent accidental foot-shooting. For the latter case, we
may set it if it passes the test to notify the user that it may be usable.
from Atheros as to what/when this is supposed to be enabled.
Using the default RX fast diversity settings seems to help quite
a bit.
Whilst I'm here, change the prototype to return HAL_BOOL rather than int.
I'm not sure whether we should install teken as a library on any stock
FreeBSD installation, but I can imagine people want to tinker around
with it now and then. Create a /sys/teken/libteken, which holds a
Makefile to install a shared library version of the terminal emulator,
complete with a manpage.
Also add Makefiles for the demo/stress applications, to build it against
the shared library.
For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX diversity; the RX antenna setting twiddles
the default antenna register. I'll try sort that stuff out at
some point.
Call the antenna switch function from the board setup function
so scans, channel changes, mode changes, etc don't set the
diversity back to a default state too far from what's intended.
Things to todo:
* Squirrel away the last antenna diversity/combining parameters
and restore them during board setup if HAL_ANT_VARIABLE is
defined. That way scans, etc don't reset the diversity settings.
* Add some more public facing statistics, rather than what's
simply logged under HAL_DEBUG_DIVERSITY.
For now, the fixed antenna settings behave better than variable
settings for me. I have some further fiddling to do..
Obtained from: Atheros
keep constant ISN growth rate, do the same directly inside tcp_new_isn(),
taking into account how much time (ticks) passed since the last call.
On my test systems this decreases idle interrupt rate from 140Hz to 70Hz.
The macro which I incorrectly copied into ah_internal.h assumed
that it'd be called with an AR_SREV_MERLIN_20() check to ensure
it was only enabled for Merlin (AR9280) silicon revision 2.0 or
later.
Trouble is, the 5GHz fast clock EEPROM flag is only valid for
EEPROM revision 16 or greater; it's assumed to be enabled
by default for Merlin rev >= 2.0. This meant it'd be incorrectly
set for AR5416 and AR9160 in 5GHz mode.
This would have affected non-default clock timings such as SIFS,
ACK and slot time. The incorrect slot time was very likely wrong
for 5ghz mode.
* Modify AR_SREV_MERLIN_20() to match the Atheros/Linux ath9k behaviour -
its supposed to match Merlin 2.0 and later Merlin chips.
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 2.0 and later chips
(AR9285, AR9287, etc.)
- instead of calling iwn_plcp_signal() for every frame, map the expected
value directly within wn->ridx
- concat plcp, rflags and xrflags, there is no clean byte boundary within
the flags, for example the antenna setting uses bit 6, 7 and 8
- there is still need for a custom rate to plcp mapping, as those expected
by the hardware are not conform to the std
On legacy channels every once in a while the firmware throws a SYSASSERT
on line 208. On HT channels though this does always happen and I'm not
aware of any workaround currently.
was not updated to pass CRD_F_KEY_EXPLICIT flag to opencrypto. This resulted in
always using first key.
We need to support providers created with this bug, so set special
G_ELI_FLAG_FIRST_KEY flag for GELI provider in integrity mode with version
smaller than 6 and pass the CRD_F_KEY_EXPLICIT flag to opencrypto only if
G_ELI_FLAG_FIRST_KEY doesn't exist.
Reported by: Anton Yuzhaninov <citrin@citrin.ru>
MFC after: 1 week
for the given channel is available.
It isn't used yet; ar5416GetWirelessModes() needs to be taught
about this rather than assuming HT20/HT40 is available.
This seems to make the AR9160 behave better during heavy scanning,
where before it'd hang and require a hard reset to recover.
Obtained From: Linux ath9k, Atheros
modifying AR_DIAG_SW.
There's a hardware workaround which sets disabling some errors
early at startup and clears said bits before the PCU begins
receiving - it does this to avoid RX descriptor status errors.
It's possible these bits aren't being completely properly twiddled
in all instances; but in particular if the diag_reg HAL variable
is set it won't be setting these bits correctly. I'll review this
at some point.
* Disable multicast search on mac address and key id - the driver
doesn't use it at the moment and thus adhoc may be broken for
merlin and later.
* Change this to be for Merlin 1.0 (which from what I understand
wasn't ever publicly released) to be more correct.
Apparently all three RX chains need to be enabled before initial calibration
is done, even if only two are configured.
Reorder the alt chain swap bit to match what the Atheros HAL is doing.
Obtained From: ath9k, Atheros
* Shuffle some of the capability numbers around to match the
Atheros HAL capability IDs, just for consistency.
* Add some new capabilities to FreeBSD from the Atheros
HAL which will be be shortly used when new chipsets are added
(HAL SGI-20 support is for Kiwi/AR9287 support); for
TX aggregation (MBSSID aggregate support, WDS aggregation
support); CST/GTT support for carrier sense/TX timeout.
channel when the channel is HT/40.
The new ANI code (primarily for the AR9300/AR9400) in ath9k sets this
register but the ANI code for the previous 11n chips didn't set this.
Unlike ath9k, only set this for HT/40 channels.
Obtained From: ath9k
These describe FCC/Japan channel and DFS behaviour.
The AR9285 and later chips don't set these bits in the eeprom, the correct
behaviour is to just assume all five bits are enabled.
An optical disk may not have a TOC (e.g. for blank media) and userland
software may legitimately try to use CDIOREADTOCHEADER to find out about
the TOC.
Silence from: scsi@
MFC after: 10 days
specific.
The Atheros HAL and FreeBSD HAL share the same capabilities up
until HAL_CAP_11D, where things begin to diverge.
I'll look at tidying these up soon.
Obtained from: Atheros
* Add Howl (ar9130) to the list of chips that have DFS/BB/MAC hangs
* Don't treat unknown BB hangs as fatal; ath9k/Atheros HAL don't
treat it as such.
* Add HAL_DEBUG_DFS to the debug fields in ath_hal/ah_debug.h
The BB hang check simply loops over an observation register checking
for a stuck state engine, but it can happen under high traffic
conditions. Ath9k and the Atheros HAL simply log a debug message and
continue.
Private to FreeBSD:
* Add HAL_DEBUG_HANG to the debug fields
* Change the hang debugging to HAL_DEBUG_HANG rather than HAL_DEBUG_DFS
like in the Atheros HAL.
Obtained from: Atheros
For now, these are equivalent macros. AR_SREV_OWL{X}_OR_LATER
will later change to exclude Howl (AR9130) in line with what
the Atheros HAL does.
This should not functionally change anything.
Obtained from: Atheros
A quick story, which is partially documented in the commit.
The silicon revision in Linux ath9k and the Atheros HAL use an
AR_SREV_REVISION mask of 0x07.
FreeBSD's HAL uses the AR5212 AR_SREV_REVISION mask of 0x0F.
Thus the OWL silicon revisions were coming through as 0xA, 0xB,
0xC, rather than 0x0, 0x1 and 0x2.
My ath9k-sourced AR_SREV_OWL_<X> macros were thus using the wrong
silicon revision values and wouldn't correctly match.
This commit does a few things:
* Change the AR_SREV_OWL_<x> macros to use the AR_SREV_REVISION_OWL_*
values, not AR_XSREV_REVISION_OWL macros;
* Disable AR_XSREV_REVISION_OWL_* values;
* Modify the IS_5416 to properly check the MAC is OWL, rather than
potentially matching on non-OWL revisions (which shouldn't happen
unless there's a silicon revision of higher than 0x9 in a later
chip..)
* Add a couple more macros from the Atheros HAL for compatibility.
The main difference now is that the Atheros HAL defines
AR_SREV_OWL_{20,22}_OR_LATER subtly differently - it fails on all HOWL
silicon. The AR_SREV_5416_*_OR_LATER macros match on the relevant OWL
version -and- all HOWL versions, along with subsequent versions.
A subsequent commit is going to migrate the uses of AR_SREV_OWL_X_OR_LATER
to AR_SREV_5416_X_OR_LATER to match what's going on in the Atheros HAL.
There's only two uses of AR_SREV_OWL_X_OR_LATER which currently don't
apply to FreeBSD but it may do in the future.
Yes, it's all confusing!
tick driving logic to xl_tick(). Now xl_tick() handles MII tick as
well as periodic updating of statistics.
This change removes a hack used in interrupt handler where it
wanted to update statistics without driving MII tick.
picking the next available one. This may explain why xl(4) sees TX
underrun error with no queued frame. I hope this addresses a long
standing xl(4) watchdog timeout issue as well.
Obtained from: OpenBSD
RX descriptor ring. Previously it returned the number of frames
that were successfully passed to upper stack which in turn means it
ignored frames that were discarded due to errors. The number of
processed frames in RX descriptor ring is used to detect whether
driver is out of sync with controller's current descriptor pointer.
Returning number of processed frames reduces unnecessary (probably
wrong) re-synchronization.
While here, remove unnecessary local variable initialization.
handler for 3C90x and 3C90xB/C respectively. This simplifies ioctl
handler as well as enhancing readability.
While I'm here don't reprogram multicast filter when driver is not
running.
Transmission error in tun(4) is queueing error(i.e. ENOBUFS) and it
has nothing to do with collision.
Reported by: Zeus V Panchenko (zeus <> ibs dot dn dot ua)
new NFS client. It will then be reduced to whatever the
server says it can support. There might be an argument
that this could be one block larger, but since NFS is
a byte granular system, I chose not to do that.
Suggested by: Matt Dillon
Tested by: Daniel Braniss (earlier version)
MFC after: 2 weeks
This also introduces a new detection path for family 10h and newer
pre-bulldozer cpus, pre-10h hardware should not be affected.
Tested by: Gary Jennejohn <gljennjohn@googlemail.com>
(with pre-10h hardware)
MFC after: 2 weeks
versions instead. They were never needed as bus_generic_intr() and
bus_teardown_intr() had been changed to pass the original child device up
in 42734, but the ISA bus was not converted to new-bus until 45720.
or f_ffree fields of "struct statfs" are negative, since the
values that go on the wire are unsigned and will appear to be
very large positive values otherwise. This makes the handling
of a negative f_bavail compatible with the old/regular NFS server.
MFC after: 2 weeks
This fixes heavy interrupt storm and resulting system freeze when using
LAPIC timer in one-shot mode under Xen HVM. There, unlike real hardware,
programming timer with zero period almost immediately causes interrupt.
this there is a rare return path that bogusly appears
to fail when it should not. Also white space correction.
Thanks to Arnaud Lacombe for noticing the problem.
Quoting the ath9k commit message:
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Reference: https://patchwork.kernel.org/patch/753862/
Obtained from: Linux ath9k
The checks should function as follows:
* AR_SREV_<silicon> : check macVersion matches that version id
* AR_SREV_<silicon>_<revision> : check macVersion and macRevision match
the version / revision respectively
* AR_SREV_<silicon>_<revision>_OR_LATER: check that
+ if the chip silicon version == macVersion, enforce revision >= macRevision
+ if the chip silicon version > macVersion, allow it.
For example, AR_SREV_MERLIN() only matches AR9280 (any revision),
AR_SREV_MERLIN_10() would only match AR9280 version 1.0, but
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 version >= 2.0 _AND_
any subsequent MAC (So AR9285, AR9287, etc.)
The specific fixes which may impact users:
* if there is Merlin hardware > revision 2.0, it'll now be correctly
matched by AR_SREV_MERLIN_20_OR_LATER() - the older code simply
would match on either Merlin 2.0 or a subsequent MAC (AR9285, AR9287, etc.)
* Kite version 1.1/1.2 should now correctly match. As these macros
are used in the AR9285 reset/attach path, and it's assumed that the
hardware is kite anyway, the behaviour shouldn't change. It'll only
change if these macros are used in other codepaths shared with
older silicon.
Obtained from: Linux ath9k, Atheros
Reference code that shows how to get a packet's timestamp out of
cxgbe(4). Disabled by default because we don't have a standard way
today to pass this information up the stack.
The timestamp is 60 bits wide and each increment represents 1 tick of
the T4's core clock. As an example, the timestamp granularity is ~4.4ns
for this card:
# sysctl dev.t4nex.0.core_clock
dev.t4nex.0.core_clock: 228125
MFC after: 1 week
- Enable 5-tuple and every-packet lookup.
- Setup the default filter mode to allow filtering/steering based on IP
protocol, ingress port, inner VLAN ID, IP frag, FCoE, and MPS match
type; all combined together. You can also filter based on MAC index,
Ethernet type, IP TOS/IPv6 Traffic Class, and outer VLAN ID but you'll
have to modify the default filter mode and exclude some of the
match-fields in it.
IPv4 and IPv6 SIP/DIP/SPORT/DPORT are always available in all filter
rules.
- Add driver ioctls to get/set the global filter mode.
- Add driver ioctls to program and delete hardware filters. A couple of
the "switch" actions that rewrite Ethernet and VLAN information and
switch the packet out of another port may not work as the L2 code is not
yet in place. Everything else, including all "drop" and "pass" rules
with RSS or absolute qid, should work.
Obtained from: Chelsio Communications
that are now in "struct statfs" for NFSv3 and NFSv4. Since
the ffiles value is uint64_t on the wire, I clip the value
to INT64_MAX to avoid setting f_ffree negative.
Tested by: kib
MFC after: 2 weeks
values of error numbers in sys/errno.h will be the same
as the ones specified by the NFS RFCs and that the code
needs to be fixed if error numbers are changed in sys/errno.h.
Suggested by: Peter Jeremy
MFC after: 2 weeks
have similar hardware features of BCM5718 family except the number
of receive return ring is 4. The BCM57765 family is known to
support IEEE 802.3az EEE(Energy Efficient Ethernet) but this change
does not include EEE support code. I hope EEE is implemented in
near future.
This change will support BCM57761, BCM57765, BCM57781, BCM57785,
BCM57791 and BCM57795. All hardware offloading features are
supported and suspend/resume also should work.
Many thanks to Broadcom for continuing support of FreeBSD.
Tested by: Paul Thornton (prt <> prt dot org)
HW donated by: Broadcom
