iteration over the fdsets, kern_select() limits the length of the
fdsets copied in by the last valid file descriptor index. If any bit
is set in a mask above the limit, current implementation ignores the
filedescriptor, instead of returning EBADF.
Fix the issue by scanning the tails of fdset before entering the
select loop and returning EBADF if any bit above last valid
filedescriptor index is set. The performance impact of the additional
check is only imposed on the (somewhat) buggy applications that pass
bad file descriptors to select(2) or pselect(2).
PR: kern/155606, kern/162379
Discussed with: cognet, glebius
Tested by: andreast (powerpc, all 64/32bit ABI combinations, big-endian),
marius (sparc64, big-endian)
MFC after: 2 weeks
built with -Wundef, as opposed to world.
Additionally, cdefs.h tends to not use indentation for preprocessor
directives, so remove that too.
Pointy hat to: me
- Improved locking and destruction process to fix crashes.
- Improved "automatic" configuration method to make it consistent and safe
by reading metadata back from all specified paths after writing to one.
- Added provider size check to reduce chance of ordering conflict with
other GEOM classes.
- Added "manual" configuration method without using on-disk metadata.
- Added "add" and "remove" commands to allow manage paths manually.
- Failed paths are no longer dropped from geom, but only marked as FAIL
and excluded from I/O operations.
- Automatically restore failed paths when all others paths are marked
as failed, for example, because of device-caused (not transport) errors.
- Added "fail" and "restore" commands to manually control FAIL flag.
- geom is now destroyed on last path disconnection.
- Added optional Active/Active mode support. Unlike Active/Passive
mode, load evenly distributed between all working paths. If supported by
the device, it allows to significantly improve performance, utilizing
bandwidth of all paths. It is controlled by -A option during creation.
Disabled by default now.
- Improved `status` and `list` commands output.
Sponsored by: iXsystems, inc.
MFC after: 1 month
cp2103 usb-to-serial chip.
- This patch also makes the line status polling asynchronous, to reduce
the time needed to change the GPIO pins.
Submitted by: JD Louw
MFC after: 1 week
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
after its installation. This removal may be accidental and can
prevent the default route from being installed in the future if
the associated default router has the best preference. The cause
is the lack of status update in the default router on the state
of its route installation in the kernel FIB. This patch fixes
the described problem.
Reviewed by: hrs, discussed with hrs
MFC after: 5 days
if_alloctype was used to store the origional interface type. Take
advantage of this change by removing all existing uses of if_free_type()
in favor of if_free().
MFC after: 1 Month
- fix other errors introduced when committing r226436
- add 'function' to a sentence where it makes sense
Submitted by: delphij
Submitted by: dougb
Submitted by: jhb
Approved by: dougb
Approved by: jhb
the length of frame should be treated as multiple of 4. Actual
frame length is set in the TX header. The TX header position
should be aligned on 4 byte boundary and actual frame start
position should be aligned on 4 byte boundary as well. This means
we need 4(TX header length) + 3(frame length fixup) additional free
space in TX buffer in addition to actual frame length.
Make sure TX handler check these additional bytes.
ae_tx_avail_size() returns actual free space in TX buffer to ease
the calculation of available TX buffer space in caller. While I'm
here, replace magic number to appropriate sizeof operator to
enhance readability.
This change should fix controller lockup issue happened under
certain conditions but it still does not fix watchdog timeout. It
seems the watchdog timeout is side-effect of TxS and TxD
mismatches. The root cause of TxD/TxD mismatch is not known yet but
it looks like silicon bug. I guess driver may have to reinitialize
controller whenever it sees TxS and TxD mismatches but leave it as
it was at this moment.
PR: kern/145918
to match native struct timespec ABI on __LP32__.
This change is a prerequisite for upcoming futimens()/utimensat() in whose
implementations it is assumed that timespec32 can take a negative value.
MFC after: 1 week
results in the HAL being built without HAL debugging/diagnostic support,
the module building process needs to be somehow taught to not build AR5416+
NICs if AH_SUPPORT_AR5416 isn't defined in opt_ah.h .
certain instructions in a function prologue or epilogue. DTrace has a
hook into the invalid opcode fault handler that checks whether the fault
was due to an probe and if so, runs the DTrace magic.
Upon returning from an invalid opcode fault caused by a probe, DTrace must
emulate the instruction that was replaced with the invalid opcode and then
return control to the instruction following the invalid opcode.
There were a pair of related bugs in the emulation for the leave
instruction. The leave instruction is used to pop off a stack frame prior
to returning from a function. The emulation for this instruction must
move the trap frame for the invalid opcode fault down the stack to the
bottom of the stack frame that is being removed, and then execute an iret.
At two points in this process, the emulation code was storing values above
the current value of the stack pointer. This opened up a window in which
if we were two take an interrupt, the trap frame for the interrupt would
overwrite the values stored on the stack, causing the system to panic
later.
The first bug was that at one point the emulation code saves the new value
for $esp above the current stack pointer value. The fix is to save this
value instead inside of the original trap frame. At this point we do
not need the original trap frame so this is safe.
The second bug is that when the emulate code loads $esp from the stack, it
points part-way through the new trap frame instead of at its beginning.
The emulation code adjusts the stack pointer to the correct value
immediately afterwards, but this still leaves a one instruction window in
which an interrupt would corrupt this trap frame. Fix this by adjusting
the stack frame value before loading it into $esp.
This fixes panics in invop_leave on i386 when using fbt return probes.
Reviewed by: rpaulo, attilio
MFC after: 1 week
This implies that users who are building the driver do so with
KERNBUILDDIR set to the compile/CONFIG directory so the various
opt_* sources can be pulled in.
I need to investigate this a little closer, but it seems that in noisy
environments the NF load takes longer than 5 * DELAY(10) and this is
messing up future NF calibrations. (The background: NF calibrations
begin at the value programmed in after the load has completed, so
if this is never loaded in, the NF calibrations only ever start at
the currently calibrated NF value, rather than starting at something
high (say -50.)
More investigation about the effect on 11n RX and calibration results
are needed.
Sponsored by: Hobnob, Inc.
The AR5416 MAC (which shows up in the AR5008, AR9001, AR9002 devices) has
issues with PCI transactions on SMP machines. This work-around enforces
that register access is serialised through a (global for now) spinlock.
This should stop the hangs people have seen with the AR5416 PCI devices
on SMP hosts.
Obtained by: Linux, Atheros
ensuring that everything is really, truly consistent.
This fixes certain cases where one will see various:
mfi0: COMMAND 0xffffffXXXXXXXXXX TIMEOUT AFTER XX SECONDS
MFC after: 3 days
Submitted by: scottl
Ok'ed by: jhb
it's cloned and that clone is retransmitted. This means that the
ath_buf pointer squirreled away on the baw window array is suddenly
wrong and was causing all kinds of console output.
This updates the pointer in that particular BAW slot to the new
ath_buf after ensuring that:
* the new and old buffers have the same seqno;
* the current slot pointer matches the old buffer pointer.
This quietens the debugging output (again), restoring said debugging
to only signify when a broken condition has occured.
Sponsored by: Hobnob, Inc.
This is a bit hackish and should be made more generic (ie, support more than
two hard-coded performance counter+config register pairs) so it can be used
for mips74k and other chips.
All this does is process the initial interrupt event. It doesn't (yet) handle
callgraph events, so even if you route the exception/interrupt to this routine
and flip the bit on, it will hang and crash pmc unless you disable callgraph
support when you enable a sample based PMC.
Luckily, it mostly wasn't important, so this didn't cause major problems.
Also improve register reuse when setting up trap frames very slightly.
Submitted by: Justin Hibbits <chmeeedalf at gmail dot com>
MFC after: 5 days
Just place the default kobj_method inside the kobjop_desc structure.
There's no need to give these kobj_methods their own symbol. This shaves
off 10 KB of a GENERIC kernel binary.
