Due to some differences in MSRs between Xeon Sandy Bridge and Core Sandy
Bridge (Model 0x2A), wrmsr() may generate in a GP# fault exception and so a
panic of the machine.
Approved by: gnn (mentor)
MFC after: 3 days
* Add an OS_A_REG_WRITE() routine - analog writes require a 100usec delay
on AR9280 and later, so create a method to do it.
* Use it for the AR9287 analog writes.
* Re-indent and style(9) the code.
This just requires a little HAL change (add a new config parameter) and
some glue in if_ath_pci.c, however I'm leaving this up for someone else
to do.
Obtained from: Qualcomm Atheros
interacts with some non-highpoint controollers. Change attach_generic to
be off by default.
PR: kern/168910
Submitted by: Richard Yao <ryao@gentoo.org>
Approved by: cperciva
No objections by: -hackers
Obtained from: Gentoo FreeBSD
MFC after: 2 weeks
* Use ATH_RC_NUM instead of '4' when iterating over the ratecontrol series
array.
* A few style(9) fixes, hopefully no regressions here.
* Add some comments that better describe what's going on.
The existing code tries to use the beacon miss timer to signal that the AP
has gone away. Unfortunately this doesn't seem to be behaving itself.
I'll try to investigate why this is for the sake of completeness.
The result is the STA will stay "associated" to the AP it was associated
with when it suspended. It never receives a bmiss notification so it
never tries reassociating.
PR: kern/169084
This includes adding support for skipping FTDI interfaces used for JTAG
leaving them for userland and just attaching to the RS232 half, similarly
to how the corresponding Linux drivers handles these kind of adapters.
While at it, sort uftdi_devs and return BUS_PROBE_SPECIFIC (because
uftdi_probe() alters the instance variables for better or worse as do
other probe routines of USB drivers) instead of 0.
- Remove duplicated entries for BeagleBone.
- Use DEVMETHOD_END.
- Use NULL instead of 0 for pointers.
- Remove some stray lines.
MFC after: 3 days
MAXPHYS should be based on PAGE_SIZE rather than SYM_CONF_DMA_BOUNDARY.
While at it, reuse the SYM_CONF_MAX_SG macro for specifying the maximum
number of DMA tags so sym(4) itself doesn't size memory beyond what's
required for handling MAXPHYS.
PR: 168928
MFC after: 3 days
* Resize some types. In particular, bfs_seqno can be uint16_t for now.
Previous work would assign the unassigned seqno a value of -1, which
I obviously can't do here.
* Remove bfs_pktdur. It was in the original code but nothing so far uses
it.
This gets ath_buf down (on my i386 system) to 292 bytes from 300 bytes.
I'd rather it be much, much smaller.
fixed for 802.11n TX, this needs to be disabled or users wlil see randomly
hanging aggregation sessions.
Whilst I'm here, remove the warning about 802.11n being full of dragons.
It's nowhere near that scary now.
ath_start() is called.
This (defaults to 10 frames) gives for a little headway in the TX ath_buf
allocation, so buffer cloning is still possible.
This requires a lot omre experimenting and tuning.
It also doesn't stop a node/TID from consuming all of the available
ath_buf's, especially when the node is going through high packet loss
or only talking at a low TX rate. It also doesn't stop a paused TID
from taking all of the ath_bufs. I'll look at fixing that up in subsequent
commits.
PR: kern/168170
growing "downward" (moving the start address down). First, an off by
one error caused the end address to be moved down an extra alignment
chunk unnecessarily. Second, when aligning the new candidate starting
address, the wrong bits were masked off.
Tested by: Andrey Zonov andrey zonov org
MFC after: 3 days
traffic.
* Create sc_mgmt_txbuf and sc_mgmt_txdesc, initialise/free them appropriately.
* Create an enum to represent buffer types in the API.
* Extend ath_getbuf() and _ath_getbuf_locked() to take the above enum.
* Right now anything sent via ic_raw_xmit() allocates via ATH_BUFTYPE_MGMT.
This may not be very useful.
* Add ATH_BUF_MGMT flag (ath_buf.bf_flags) which indicates the current buffer
is a mgmt buffer and should go back onto the mgmt free list.
* Extend 'txagg' to include debugging output for both normal and mgmt txbufs.
* When checking/clearing ATH_BUF_BUSY, do it on both TX pools.
Tested:
* STA mode, with heavy UDP injection via iperf. This filled the TX queue
however BARs were still going out successfully.
TODO:
* Initialise the mgmt buffers with ATH_BUF_MGMT and then ensure the right
type is being allocated and freed on the appropriate list. That'd save
a write operation (to bf->bf_flags) on each buffer alloc/free.
* Test on AP mode, ensure that BAR TX and probe responses go out nicely
when the main TX queue is filled (eg with paused traffic to a TID,
awaiting a BAR to complete.)
PR: kern/168170
then solves because of cache coherency issues. This fixes periodic error
messages on console and command timeouts.
- Patch SATA PHY configuration for 65nm SoCs to improve SNR same as
Linux does.
MFC after: 2 weeks
(or direct dispatch) behind the TXQ lock (which, remember, is doubling
as the TID lock too for now.)
This ensures that:
(a) the sequence number and the CCMP PN allocation is done together;
(b) overlapping transmit paths don't interleave frames, so we don't
end up with the original issue that triggered kern/166190.
Ie, that we don't end up with seqno A, B in thread 1, C, D in
thread 2, and they being queued to the software queue as "A C D B"
or similar, leading to the BAW stalls.
This has been tested:
* both STA and AP modes with INVARIANTS and WITNESS;
* TCP and UDP TX;
* both STA->AP and AP->STA.
STA is a Routerstation Pro (single CPU MIPS) and the AP is a dual-core
Centrino.
PR: kern/166190
scheduled from the head of the software queue rather than trying to
queue the newly given frame.
This leads to some rather unfortunate out of order (but still valid
as it's inside the BAW) frame TX.
This now:
* Always queues the frame at the end of the software queue;
* Tries to direct dispatch the frame at the head of the software queue,
to try and fill up the hardware queue.
TODO:
* I should likely try to queue as many frames to the hardware as I can
at this point, rather than doing one at a time;
* ath_tx_xmit_aggr() may fail and this code assumes that it'll schedule
the TID. Otherwise TX may stall.
PR: kern/166190
This is an unfortunate byproduct of how the routine is used - it's called
with the head frame on the queue, but if the frame is failed, it's inserted
into the tail of the queue.
Because of this, the sequence numbers would get all shuffled around and
the BAW would be bumped past this sequence number, that's now at the
end of the software queue. Then, whenever it's time for that frame
to be transmitted, it'll be immediately outside of the BAW and TX will
stall until the BAW catches up.
It can also result in all kinds of weird duplicate BAW frames, leading
to hilarious panics.
PR: kern/166190
This showed up when doing heavy UDP throughput on SMP machines.
The problem with this is because the 802.11 sequence number is being
allocated separately to the CCMP PN replay number (which is assigned
during ieee80211_crypto_encap()).
Under significant throughput (200+ MBps) the TX path would be stressed
enough that frame TX/retry would force sequence number and PN allocation
to be out of order. So once the frames were reordered via 802.11 seqnos,
the CCMP PN would be far out of order, causing most frames to be discarded
by the receiver.
I've fixed this in some local work by being forced to:
(a) deal with the issues that lead to the parallel TX causing out of
order sequence numbers in the first place;
(b) fix all the packet queuing issues which lead to strange (but mostly
valid) TX.
I'll begin fixing these in a subsequent commit or five.
PR: kern/166190
Return PROTO_ATA protocol in response to XPT_PATH_INQ.
smartmontools uses it to identify ATA devices and I don't know any other
place now where it is important. It could probably use XPT_GDEV_TYPE
instead for more accurate protocol information, but let it live for now.
Reported by: matthew
MFC after: 3 days
suspend/resume procedures are minimized among them.
common:
- Add global cpuset suspended_cpus to indicate APs are suspended/resumed.
- Remove acpi_waketag and acpi_wakemap from acpivar.h (no longer used).
- Add some variables in acpi_wakecode.S in order to minimize the difference
among amd64 and i386.
- Disable load_cr3() because now CR3 is restored in resumectx().
amd64:
- Add suspend/resume related members (such as MSR) in PCB.
- Modify savectx() for above new PCB members.
- Merge acpi_switch.S into cpu_switch.S as resumectx().
i386:
- Merge(and remove) suspendctx() into savectx() in order to match with
amd64 code.
Reviewed by: attilio@, acpi@
until transport will do some probe actions (at least soft reset).
Make ATA/SATA SIMs to not report bogus and confusing PROTO_ATA protocol.
Make ATA/SATA transport to fill that gap by reporting protocol to SIM with
XPT_SET_TRAN_SETTINGS and patching XPT_GET_TRAN_SETTINGS results if needed.
