1.6 2000/04/12 21:07:55 scw
Add support for the SOHOware PCMCIA Ethernet card, model ND5100-E.
This seems to be a re-badged NDC (National Datacomms. Corp) card.
It needs a quirk entry due to lack of manufacturer tuple in the CIS.
For some reason, the 'Tx/Rx' LED on the connector module is inverted
such that it is off during network activity...
bus/slot/function numbers. The old PCI code used other markers or
something, but without it here under the new pci code it is very hard to
tell which device is which (this only affects bootverbose mode).
PR kern/20895:
- Add FE_DAC new feature flag to distinguish between
64 bit PCI addressing (DAC cycles) and 64 bit PCI
interface (64 bit Memory BARs).
- Properly deal with chips that have a 32 bit PCI
interface but support and may generate DAC.
(Only SYM53C895A for now).
PR misc/17584 (at least partially addressed):
- Try detecting hardware combinations that trigger
spurious PCI master parity error detections by the
PCI chip. This work-around is implemented in the
`snooptest' routine and consists in retrying with
PCI master parity checking disabled if such an
error is reported by the PCI chip during this test.
Other:
- Fix a tiny bug in WIDE negotiation that was very
unlikely to be triggerred. The BUS width was wrongly
compared against chip's max. offset.
#includes "smbus.h". There is still some bogus (but harmless) stuff
here surrounding the #include <sys/bus.h> includes here and elsewhere in
the bktr code.
cloning infrastructure standard in kern_conf. Modules are now
the same with or without devfs support.
If you need to detect if devfs is present, in modules or elsewhere,
check the integer variable "devfs_present".
This happily removes an ugly hack from kern/vfs_conf.c.
This forces a rename of the eventhandler and the standard clone
helper function.
Include <sys/eventhandler.h> in <sys/conf.h>: it's a helper #include
like <sys/queue.h>
Remove all #includes of opt_devfs.h they no longer matter.
the link and activity LED control bits in CSR15 in order for the
controller to drive the LEDs correctly. This was largely done for the
ZNYX multiport cards, but should also work with the DEC DE500-BA
and other non-MII cards.
enable bit hasn't been set in the command register, set the bit and
honour the register. It seems that quite a few lazy BIOS writers
aren't bothering to do this, which upsets the existing code and causes
us to miss out on properly-configured devices.
pcib instance is initialized because accesses to PCI_Config region can
occur during ACPI initialization.
Note that this is a short term solution, more consideration will be
required in order to integrate ACPI into the newbus probe sequence.
change channel interface - kobj implementation coming soonish
make pcm_makelinks not panic if modular
add pcm_unregister()
these changes support newpcm kld unloading, but this is only implemented
by ds1.c
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
- Remove DELAY() kludge before power off.
- Move EVENTHANDLER_REGISTER to acpi_attach().
- Pass RB_POWEROFF flag to shutdown_nice().
Reviewed by: msmith
kernel can instigate an orderly shutdown but still determine the form of
that shutdown. Make it possible eg. to cleanly shutdown and power off the
system under ACPI when the power button is pressed.
- New support for 40LD firmware found in Series 475 and 471 adapters.
- Better support for 8LD firmware adapters
- Ioctl passthrough interface for userland utilities.
- Improved error handling and queueing.
- Several bugfixes (including the 'still open' shutdown bug and
closing some small race conditions).
- Zone-style command allocator, reducing memory wasted under heavy
load conditions.
- CAM interface (disabled and not fully working) for SCSI passthrough
access to non-disk devices
Thanks to AMI for supplying a pile of new adapters and various other
help in making this happen.
- Add new funcions for device state stuff;
acpi_get_current_device_state() and acpi_set_device_state()
- Add new funcions for power resource stuff;
acpi_powerres_init(), acpi_powerres_debug(),
acpi_get_current_powerres_state() and acpi_set_powerres_state()
These were implemented based on 7.1, 7.2, 7.2.2, 7.2.3, 7.2.4, 7.3,
7.3.3, 7.4, 7.4.1, 7.4.2, 7.4.3 and 7.5 of ACPI spec 1.0b.
- The "Osd*" stuff went away from acpi driver code, use the bus_space
functions directly instead.
- Fix minor english bugs.
acpi_registers_input -> acpi_register_input
acpi_registers_output -> acpi_register_output
- Remove all magic numbers for the sleeping states. We now have
#defines for these.
- NULL is treated the same as the return from aml_get_rootname in
aml_find_from_namespace().
Suggested by: msmith
Thanks mike!
