Kernel Appletalk protocol support
both CAP and netatalk can make use of this..
still needs some owrk but it seemd the right tiime to commit it
so other can experiment.
guru out there can find a way to take advantage of little-endianness to
make this computation more efficient. (I am certain that it can be done,
but haven't managed to make it work myself.)
unconventionally:
If COMPAT_IPFW is not defined, or if it is defined to 1, enable;
otherwise, disable.
This means that these changes actually have no effect on anyone at the
moment. (It just makes it easier for me to keep my code in sync.)
In the future, the `not defined' part of the hack should be eliminated,
but doing this now would require everyone to change their config files.
The same conditionals need to be made in ip_input.c as well for this to
ave any useful effect, but I'm not ready to do that right now.
call of ahc_scsirate. Otherwise, the proper setting may not get set until
the next reconnection/selection.
The saved_queue used to re-order the QINFIFO during error recovery or
certain SCB paging operations should be an array of u_chars not ints.
saved_queue type error pointed out by: Noriyuki Soda <soda@sra.co.jp>
comparing the PTD pointers, they needed to be masked by PG_FRAME, and
they weren't. Also, the "improved" non-386 code wasn't really an
improvement, so I simplified and fixed the code. This might have
caused some of the panics caused by the VM megacommit.
I spent the better part of a day trying to figure out why my
experiment didn't work the way I expected, only to find out that
the router was dropping huge numbers of packets because of PCI bus
priblems. This does not fix the bug that errors are counted as
input packets because my patch doesn't apply cleanly.
to use the full range of settings from 3.6-20MHz on any target.
Remove all Ultra settings except for the top three that are documented
to work. This fixes some problem reports with the last revision of the
driver since at least the 5.7MHz entry doesn't work in Ultra mode.
With this fix from Stephen, we are getting the target fork performance
that I have been trying to attain: P5-166, before the mega-commit: 700-800usecs,
after: 600usecs, with Stephen's fix: 500usecs!!! Also, this could be the
solution of some strange panic problems...
Reviewed by: dyson@freebsd.org
Submitted by: Stephen McKay <syssgm@devetir.qld.gov.au>
snuck in accidentally from the DARTNet kernel. SIOC*RTINFO were an
extended interface to the stock routing table and SIOCGETVIFINF was
an interface for rsvpd to ask the kernel for the list of multicast vif's.
Pointed-out-by: Brian Reichert <reichert@internet.com>
is enabled by having an "device ed0 at isa? [...]" config line.
The first PCI card will get a unit number one higher than the highest
defined for any ISA card of the ED type, e.g. if ed0 and ed1 are
configured, then the PCI cards will be ed2, ed3, ...
BEWARE: If you have configured your kernel as ed0 with the port address
as assigned by the PCI BIOS, then your card will be found by both the
PCI and ISA probes, and bad things may happen. Make sure to restore
the original port address form the GENERIC kernel for the ed0 device!
Reviewed by: davidg
contributions or ideas from Stephen McKay <syssgm@devetir.qld.gov.au>,
Alan Cox <alc@cs.rice.edu>, David Greenman <davidg@freebsd.org> and me:
More usage of the TAILQ macros. Additional minor fix to queue.h.
Performance enhancements to the pageout daemon.
Addition of a wait in the case that the pageout daemon
has to run immediately.
Slightly modify the pageout algorithm.
Significant revamp of the pmap/fork code:
1) PTE's and UPAGES's are NO LONGER in the process's map.
2) PTE's and UPAGES's reside in their own objects.
3) TOTAL elimination of recursive page table pagefaults.
4) The page directory now resides in the PTE object.
5) Implemented pmap_copy, thereby speeding up fork time.
6) Changed the pv entries so that the head is a pointer
and not an entire entry.
7) Significant cleanup of pmap_protect, and pmap_remove.
8) Removed significant amounts of machine dependent
fork code from vm_glue. Pushed much of that code into
the machine dependent pmap module.
9) Support more completely the reuse of already zeroed
pages (Page table pages and page directories) as being
already zeroed.
Performance and code cleanups in vm_map:
1) Improved and simplified allocation of map entries.
2) Improved vm_map_copy code.
3) Corrected some minor problems in the simplify code.
Implemented splvm (combo of splbio and splimp.) The VM code now
seldom uses splhigh.
Improved the speed of and simplified kmem_malloc.
Minor mod to vm_fault to avoid using pre-zeroed pages in the case
of objects with backing objects along with the already
existant condition of having a vnode. (If there is a backing
object, there will likely be a COW... With a COW, it isn't
necessary to start with a pre-zeroed page.)
Minor reorg of source to perhaps improve locality of ref.
1) A spelling error pointed out by Paco Hope.
2) A bug in the range checking routing pointed out by Jim Bray.
3) Enables the setting of frames per second.
Submitted-By: Jim Lowe <james@miller.cs.uwm.edu>
use sd87a or sd237e even if they start at the beginning of the slice.
You can also use sd85c if you prefer, although you need to change the
type field in the disklabel to "4.2BSD".
unreasonable time. I've got a PCI mainboard that simply doesn't grok
it, so continuing with a warning (and a keyboard that's working
nevertheless :) seems to be better than spin-looping forever.
a BIOS was not installed, this will still be true by the time we probe
the chip. We use this heuristic to determine if we should use the left
over scratch ram target settings for controllers that don't have an
SEEPROM. We also "snapshot" the host adapter SCSI id and whether ultra
is enabled or not and use these values if a BIOS was installed. The card
will act as if a BIOS was installed even if there wasn't one if you warm
reboot, but since the scratch ram area is still valid in this case, its
hardly worth the effort of writing a shutdown routing that clears out
the scratch ram. This should make users of motherboard controllers
happy.
channel B first as approriate.
Only reset the SCSI bus if the RESET_SCSI bit of SCSICONF is set. This
makes the aic7xxx driver honor all of the configuration settings availible
in SCSI-Select or the ECU.
Fix a benign bug in the reset code that caused us to always wait a full
second after the chip reset. This should shave some time off the probe.
Bug found by pedrosal@nce.ufrj.br (Pedro Salenbauch)
It seems that only the top three sync rates are doubled when in ultra mode,
so update the syncrates table as appropriate.
Found by "Dan Willis" <dan@plutotech.com> and his SCSI bus analyzer
channel B first as approriate.
Even if the BIOS is diabled, the ECU will still set the primary channel
bit, SCSI ID, RESET_SCSI bit, and BOFF_TIME, so use them.
Change #ifdef linux to #ifdef __linux__
aic7xxx_reg.h:
Remove unneeded BOFF_60BCLOCKS
define CHIPRSTACK to be the same as CHIPRST
define RESET_SCSI and CHANNEL_B_PRIMARY bits
All of these aer used during the setup of adapters.
(PR #1178).
Define a new SO_TIMESTAMP socket option for datagram sockets to return
packet-arrival timestamps as control information (PR #1179).
Submitted by: Louis Mamakos <loiue@TransSys.com>
boundary, which means that it doesn't mark the start of the data
section (which is then inaccessible to the programmer ??).
Hopefully fixes recent locore reboot problems.
the past, since it returns to the old system of allocating mbufs out of
a private area rather than using the kernel malloc(). While this may seem
like a backwards step to some, the new allocator is some 20% faster than
the old one and has much better caching properties.
Written by: John Wroclawski <jtw@lcs.mit.edu>
second delay. My ps/2 mouse is now found reliably on my ThinkPad (it
didn't before) and still works on my NEC Versa.
Submitted by: Richard Wiwatowski <rjwiwat@adelaide.on.net>
config file instead of hard-coding it in the driver. No functional
differences.
This is based on the code Richard Wiwatowski <rjwiwat@adelaide.on.net>
sent to the mailing list.
- Prepend PSM_ to some defines to avoid any possible name-space problems
- Use some already defined constants instead of magic #'s where appropriate.
[ No functional changes (yet) ]
the destination represents. For IP:
- Iff it is a host route, RTF_LOCAL and RTF_BROADCAST indicate local
(belongs to this host) and broadcast addresses, respectively.
- For all routes, RTF_MULTICAST is set if the destination is multicast.
The RTF_BROADCAST flag is used by ip_output() to eliminate a call to
in_broadcast() in a common case; this gives about 1% in our packet-generation
experiments. All three flags might be used (although they aren't now)
to determine whether a packet can be forwarded; a given host route can
represent a forwardable address if:
(rt->rt_flags & (RTF_HOST | RTF_LOCAL | RTF_BROADCAST | RTF_MULTICAST))
== RTF_HOST
Obviously, one still has to do all the work if a host route is not present,
but this code allows one to cache the results of such a lookup if rtalloc1()
is called without masking RTF_PRCLONING.
it empties all of the 256 byte incoming fifo, as it can spend more time
processing one port than intended, especially if data is streaming in
at 115.2K. The port fifo will be emptied and dumped into the tty system
and left until next time. I've been running this for quite some time on
one of my systems here.
Also, if the tty layer is blocked or full it lets the hardware assert the
flow control rather than loosing the data.
Compile for FreeBSD-2.2
Fix some compile warnings about function declarations
-current's VM include files have changed lately, this needed to be updated.
Use correct major number.
This is now two seperate drivers that support (I think) all of Stallions's
range, including the high performance intelligent cards, and their older
cards.
Submitted by: Greg Ungerer (gerg@stallion.oz.au)
(User-mode parts and patches to follow)
boards by Greg Ungerer (gerg@stallion.oz.au). (v0.0.1 alpha)
This is a multiple import of all revisions available to build up
a history.
This driver supports only some of the Stallion range, in particular, not
the highly intelligent cards. That comes in shortly.
Submitted by: Greg Ungerer (gerg@stallion.oz.au)
