If _ANSI_SOURCE or _POSIX_SOURCE is defined, then <ctype.h> had to
be included before <stddef.h> or <stdlib.h> to get rune_t declared.
Now rune_t is declared perfectly bogusly in all cases when <ctype.h>
is included.
This change breaks similar (but more convoluted) convolutions in the
stddef.h in gcc distributions. Ports of gcc should avoid using the
gcc headers.
page dir+table index.
pmap.h: remove NUPDE, it was wrong and not used. Sanitize KSTKPTEOFF.
vmparam.h: Calculate virtual addr from PDI+PTI from pmap.h rather than
using magic math. Remove UPDT, not used.
Intended for sup mirrors etc. Not well tested yet.
Reviewed by: phk
Submitted by: Giles Lean <giles@nemeton.com.au>
Submitted by: John Hay <jhay@mikom.csir.co.za>
In __initdb(), a failure to open the local password database is supposed
to result in a warning message being syslog()ed. This warning is only
supposed to be generated as long as the 'warned' flag hasn't been yet;
once the warning is generated, the flag should be set so that the message
is only syslog()ed once. However, while the state of the flag is checked
properly, the flag's state is never changed, so you always get multiple
warnings instead of just one.
Pointed out by: Peter Wemm
Set_Boot_Blocks(). Boy, this one had me tearing my hair out!
I hate how the loader distinguishes between `extern char *foo' and
`extern char foo[]' sometimes! :-)
More asthetic adjustments to menus.
Improve both the display efficiency and usability of the label
screen - it's now possible to label quite a few disks in the label editor.
Ensure that queued commands are not touched by the abort code by setting
the SCB status to indicate what queue it is in.
Fix deadlocks when using SCB paging by using SCBs from the assigned_scbs
queue or an SCB that completed during the same interrupt if needed.
Don't ever use insl to pull SCBs from any of the controllers. You can
only do 8bit PIO reads. This only affected SCB paging.
With this checkin, SCB paging works quite a bit better, but I still have
some problems with it that may be caused by a firmware problem in my
PD1800s. It seems that using a tag number higher than the maximum number
of tags allowed by the device, confuses it. For example, if I queue
two commands, tagged 3 and 36, it never reconnects for tag 36.
yp_dblookup.c:
- Implement database handle caching. What this means is that instead
of opening and closing map databases for each request, we open a
database and save the handle (and, if requested, the key index)
in an array. This saves a bit of overhead on things like repeated
YPPROC_NEXT calls, such as you'd get from getpwent(). Normally,
each YPPROC_NEXT would require open()ing the database, seeking
to the location supplied by the caller (which is time consuming with
hash databases as the R_CURSOR flag doesn't work), reading the
data, close()ing the database and then shipping the data off to
the caller. The system call overhead is prohibitive, especially
with very large maps. By caching the handle to an open database,
we elimitate at least the open()/close() system calls, as well
as the associated DB setup and tear-down operations, for a large
percentage of the time. This improves performance substantially at
the cost of consuming a little more memory than before.
Note that all the caching support is surrounded by #ifdef DB_CACHE
so that this same source module can still be used by other programs
that don't need it.
- Make yp_open_db() call yp_validdomain(). Doing it here saves cycles
when caching is enabled since a hit on the map cache list by
definition means that the domain being referenced is valid.
- Also make yp_open_db() check for exhaustion of file descriptors,
just in case.
yp_server.c:
- Reorganize things a little to take advantage of the database
handle caching. Add a call to yp_flush_all() in ypproc_clear_2_svc().
- Remove calls to yp_validdomain() from some of the service procedures.
yp_validdomain() is called inside yp_open_db() now, so procedures that
call into the database package don't need to use yp_validdomain()
themselves.
- Fix a bogosity in ypproc_maplist_2_svc(): don't summarily initiallize
the result.maps pointer to NULL. This causes yp_maplist_free()
to fail and leaks memory.
- Make ypproc_master_2_svc() copy the string it gets from the database
package into a private static buffer before trying to NUL terminate it.
This is necessary with the DB handle caching: stuffing a NUL into the
data returned by DB package will goof it up internally.
yp_main.c:
- Stuff for DB handle caching: call yp_init_dbs() to clear the
handle array and add call to yp_flush_all() to the SIGHUP
signal handler.
Makefile.yp:
- Reorganize to deal with database caching. yp_mkdb(8) can now be used
to send a YPPROC_CLEAR signal to ypserv(8). Call it after each map
is created to refresh ypserv's cache.
- Add support for mail.alias map.
Contributed by Mike Murphy (mrm@sceard.com).
- Make default location for the netgroups source file be /var/yp/netgroup
instead of /etc/netgroup.
mkaliases:
- New file: script to generate mail.alias map.
Contributed by Mike Murphy (mrm@sceard.com).
Makefile:
- Install Makefile.yp as /var/yp/Makefile.dist and link it to
/var/yp/Makefile only if /var/yp/Makefile doesn't already exist.
Suggested by Peter Wemm.
- Install new mkaliases script in /usr/libexec along with mknetid.
- Use somewhat saner approach to generating rpcgen-dependent files
as suggested by Garrett Wollman.
