the PIRQD bit.
This fixes the problem of uhub0 hanging forever during boot when USB
keyboard support is switched on in the BIOS on motherboards with Intel
chipsets (UHCI).
Approved by: The Sheep
fix support for multiple HPT & Promise controllers.
support mixed 33/66 devices on the Promise 66 controllers.
fix the refcount stuff in the atapi drivers.
misc cleanups.
support is also included for the ASC38C1600 Ultra160 chipset, but
as firmware is not yet available for this chip, it is disabled.
Approved by: jkh@FreeBSD.org
Also update wicontrol to enable/disable encryption, set WEP keys and set the
TX key index. Silver cards only have 40-bit keys. This is something of a quick
hack, but it works well enough for me to commit this from the LinuxWorld
exhibit floor.
The WEP support only shows up if you have a card that supports it.
Would have been approved by: jkh, if he hadn't wandered off somewhere
Approved in his place by: msmith, who's standing right here
bus_delete_resource.
Fixes a problem when the probe succeeded, but the attach failed. The
release of the resources was done inproperly.
Approved by: jkh
are using an old unconverted driver. Most (if not all) of the drivers
for common hardware are newbus these days. However, we don't want
to encourage people to take the easy way out and write new drivers
using the shims. This is just passive "encouragement".
Reviewed by: phk
Some controllers submit bogus pointers to the Done queue.
ohci_hash_find_td fails to find these in its hash and panics. Instead of
panicing we now assume the whole done queue is lost and let the timeout
code to clean up the mess after us.
condition.
- 1 line change that allows to balance chips between ncr
and sym using pci compat option (not compiled by default
in 4.0 but maintains the driver source 3.4 compatible).
uhci_check_intr() routine needs to be more careful about deciding when
the end of a transfer has been detected.
This allows me to remove the nasty workaround code from if_aue and if_cue.
Receive performance is now much better for these adapters (500KB/sec
vs. 350KB/sec).
Also removed unused KUE_CUTOFF define from if_kuereg.h.
Submitted by: Lennart Augustsson
Reviewed by: n_hibma
Try to support older systems reporting irq0 for the first channels.
Support sharing of the std interrupts (says peter :) )
Dont use READ_CD on normal data reads (2048 bytes), too many old drives
doesn't support this command even if the std says "shall" :(, but still
use READ_CD on all other blocksizes.
Add the geometry to the ad probe, its still usefull.
does ignore DCD. Even TIOCMGET cannot read DCD as the firmware doesn't
report it. This has pretty interesting effects for ppp(8) which runs
in clocal mode and polls carrier (!). (Specialix's linux driver does
this too)
Also update the firmware to 3.0.6 for the SX cards, as apparently there
was a problem with floating (disconnected) DCD pins causing stray carrier
transitions, especially at port open time.
It seems to work here, and carrier loss is detected nearly immediately
rather than having to wait for a LQR timeout (a few minutes) before ppp(8)
gives up.
DCD problem noted by: nsayer
Dont be so verbose in the probe, only ONE line printed now, to get more
info boot verbose. Centralise most printf's in ata-all & ata-dma to use
the ata_printf function, it saves alot of codelines.
Repeat the identify command if drive fails the first.
Protect the timeout functions with splbio.
Dont update the transfer details before we are sure the transfer
succeded, this way they are proberly retried on errors.
Move the handling of next_writeable to userland.
Use the READ_CD command to read CD's. That enables us to read _anything_
via the normal read/write interface. This kindof obsoletes the READAUDIO
ioctl, but we keep that for now.
Update i2c code to build on FreeBSD 3.x and 4.x machines.
Added GPIO audio values for the Askey/Dynalink TV card talken from postings on the V4L mailing list.
Update Australian Channel Set. Submitted by John Birrell <jb@cimlogic.com.au>
Add new Channel Set for France. Submitted by Daniel Dagneaux <dagneaux@lure.u-psud.fr>
doesn't conflict with the parallel port on my miata (0x3bc..0x3bf).
The right solution will be to reserve two port ranges in vga, 0x3b0..0x3ba
and 0x3c0..0x3ca.
Reviewed by: yokota
o Cut out the probed stuff. We no longer need it since newbus implicitly
checks for this (likely bt can be changed as well in this way).
o Add preliminary support for unload. Untested because aha doesn't yet
support identify and there are some interactions with PnP that I've
not yet worked out.
With this I can boot the AHA-1542CP FW F.0. All the aha resources
appear to be picked up via pnp now.
The files were repo copied from their original location and are part
way towards being portable.
This should unbreak the EISA support in the driver.
I have not updated files* yet as I'm not quite finished.
the resource table to locate children. The 'at ppbus?' can go again.
Remove a few #if Nxxx > 0' type things, config arranges this for us.
Move the newbus method glue next to the DRIVER_MODULE() stuff so we
don't need extra prototypes.
Don't set device descriptions until after the possibility of the probe
returning an error.
Remove all cdevsw_add() calls, all the drivers that did this also use
make_dev() correctly, so it's not required.
A couple of other minor nits.
isa_device->id_ri_flags and RI_FAST were not implemented and did nothing.
The two drivers that were mistakenly thinking this was working were
cy.c and loran.c - these should be converted to newbus.
GC (garbage collect) isa_device->id_alive
GC userconfig.c references to isa_device->id_scsiid (!).
Fix a long-standing bug where I used a 'break;' instead of a 'continue;';
you had to have multiple ISA boards in non-PnP mode with an 'unknown' board
with a lower MAC address to find this one. Since I have 4 3c5x9 boards
in my test box I was somewhat confused when this happened. :)
Make the messages printed by ep_isa_identify() a little more consistent;
we'll only see them in verbose boot mode but it makes me feel better if
they look nice.
Also, while I'm here, add a mechanism to catch unknown board IDs that
are likely to be 3c509s and allow them to be attached.
PR: kern/16304
Submitted by: Kelly Yancey <kbyanc@posi.net>
Many ed-based Ethernet PC-cards can't get correct MAC address without
this patch.
Submitted by: Takanori Watanabe <takawata@shidahara1.planet.sci.kobe-u.ac.jp>
Reviewed by: Warner Losh <imp@village.org>
methods for USB devices.
However: with none of the devices I have here suspend seems to work
properly. This is probably a bug in uhci_power which I still have to
look at.
Prodded and pushed by: Christopher Masto <chris@netmonger.net>
- Sync ohci, uhci and usbdi modules with NetBSD in order to obtain the
following improvements:
o New USBD_NO_TSLEEP flag can be used in place of UQ_NO_TSLEEP
quirk. This allows drivers to specify busy waiting only for
certain transfers (namely control transfers for reading/writing
registers and stuff).
o New USBD_FORCE_SHORT_XFER flag can be used to deal with
devices like the ADMtek Pegasus that sense the end of bulk OUT
transfers in a special way (if a transfer is exactly a multiple
of 64 bytes in size, you need to send an extra empty packet
to terminate the transfer).
o usbd_open_pipe_intr() now accepts an interval argument which
can be used to change the rate at which the interrupt callback
routine is invoked. Specifying USBD_DEFAULT_INTERVAL uses the
value specified in the device's config data, but drivers can
override it if needed.
- Change if_aue to use USBD_FORCE_SHORT_XFER for packet transmissions.
- Change if_aue, if_kue and if_cue to use USBD_NO_TSLEEP for all
control transfers. We no longer force the non-tsleep hack for
bulk transfers since these are done asynchronously anyway.
- Removed quirk entry fiddling from if_aue and if_kue since we don't
need it anymore now that we have the USBD_NO_TSLEEP flag.
- Tweak ulpt, uhid, ums and ukbd drivers to use the new arg to
usbd_open_pipe_intr().
- Add a flag to the softc struct in the ethernet drivers to indicate
when a device has been detached, and use this flag to perform
tests to prevent the drivers from trying to do control transfers
if this is the case. This is necessary because calling if_detach()
with INET6 enabled will eventually result in a call to the driver's
ioctl() routine to delete the multicast groups on the interface,
which will result in attempts to perform control transfers. (It's
possible this also happens even without INET6 support enabled.) This
is pointless since we know that if the detach method has been called,
the hardware has been unplugged.
- Changed watchdog timeout routines to just call the driver init routines
to initialize the device states without trying to close and re-open the
pipes. This is partly because we don't want to frob things at interrupt
context, but also because this doesn't seem to work right and I don't
want to panic the system just because a USB device may have stopped
responding.
- Fix aue_rxeof() to be a little smarter about detecting when a double
transfer is needed. Unfortunately, the design of the chip makes it hard
to get this exactly right. Hopefully, this will go away once either
Nick or Lennart finds the bug in the uhci driver that makes this ugly
hack necessary.
- Also sync usbdevs with NetBSD.
This is just to make sure we initialize the chip correctly: we need to
make the sure the port select bit in CSR6 is set properly so that we
use the internal PHY for 10/100 support. (The eval boards I have also
include an external HomePNA PHY, but I need to play with that more
before I can support it.)
- The busy wait hack in usbdi.c was doing its timeout in microseconds
instead of milliseconds.
- if_aue.c:aue_intr() is creating a bitmask by and'ing two bits when it
should be or'ing them.
Submitted by: Lennart Augustsson
correctly on both master and slave.
Smash together the ata_params & atapi_params structures as they
are more or less equal anyways.
Get rid of the last SYSINIT's in here.
the same vendor and logical ID. The rest I am not sure whether they
are vendor or logical, but it won't hurt if I've put a vendor ID here
as merely will not match. These came from the old sio-pnp code, hence
the uncertainty about which ID it is.
running. It turns out that trying to read the MAC address when there's
no firmware creates a zero length transfer. This apparently doesn't
hurt anything on a UHCI controller, but OHCI controllers generate an
IOERROR, and the device doesn't initialize.
Instead, check the bcdDevice revision code. We know this will be
different when the firmware is running, so if we detect the firmware's
code instead of the bare hardware's code, we skip the firmware load.
Prober support for the VIA 82C686, I finally got the right datasheet.
Get rid of atapi_wait, merge it into ata_wait.
Avoid a couple of races by using asleep instead of tsleep.
Always use 16bit transfers on ISA systems.
Clear up the atapi_read/write functions.
of the Broadcom BCM5201 PHY on the LinkSys USB100TX adapter so that the
link LED correctly (lights up amber for 10mbps link, green for 100mbps
link).
Note that the sticker on the bottom of the adapter says amber for 10
and green for 100, but the appendix in the manual that comes with
the adapter says green for 10 and amber for 100. Given that there doesn't
seem to be any way to make the hardware produce the latter combination,
I think it's safe to say the sticker is right and the manual is wrong.
I'm just shocked, shocked I tell you.
- Split terminal emulation code from the main part of the driver so
that we can have alternative terminal emulator modules if we like in
the future. (We are not quite there yet, though.)
- Put sysmouse related code in a separate file, thus, simplifying the
main part of the driver.
As some files are added to the source tree, you need to run config(8)
before you compile a new kernel next time.
You shouldn't see any functional change by this commit; this is only
internal code reorganization.
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
