When initializing the fdt, query U-Boot as well.
With this change, it is now feasible to have U-Boot load
the FDT, ubldr will pull it from U-Boot and hand it to the
kernel.
- fix indentation
- put the operator at the end of the line for long statements
- remove spaces between the type and the variable in a cast
- remove excessive parentheses
Tested by: md5
This has reduced the number of TX delimiter and data underruns when
doing large UDP transfers (>100mbit).
This stops any HAL_INT_TXURN interrupts from occuring, which is a good
sign!
Obtained from: Qualcomm Atheros
* Delete this debugging print - I used it when debugging the initial
TX descriptor chaining code. It now works, so let's toss it.
It just confuses people if they enable TX descriptor debugging as they
get two slightly different versions of the same descriptor.
* Indenting.
part of ts_status. Thus:
* make sure we decode them from ts_flags, rather than ts_status;
* make sure we decode them regardless of whether there's an error or not.
This correctly exposes descriptor configuration errors, TX delimiter
underruns and TX data underruns.
seems to cause more problems then previous behavior: it either breaks
initilization sequence in other places or uncovers problems with
high-speed mode timing for SDHCI 3.0
Make dcons input polling adaptive, reducing poll rate to 1Hz after several
minutes of inactivty to reduce global interrupt rate. Most of users never
used FireWire debugging, so it is not very useful to consume power by it.
Fix pull-up and pull-down values of gpio.
According to A10 user manual possible pull register
values are 00 Pull-up/down disable, 01 Pull-up, 10 Pull-down.
Approved by: gonzo@
This will be used by some upcoming changes to loader(8) FDT
handling to allow it to use an FDT provided by an earlier
boot stage the same as an FDT loaded from disk.
unnecessarily by a user thread waiting to run on a specific CPU after
calling sched_bind().
Reviewed by: rstone
Approved by: emaste (co-mentor)
Sponsored by: Sandvine Incorporated
MFC after: 1 week
submap. Otherwise, after r246204, the auto-scaling logic in kern_malloc.c
tries to create a kmem submap that consumes the entire kernel map on a
Pandaboard with 1 GB of RAM.
Tested by: gonzo
machine to another. Therefore, VM_MAX_KERNEL_ADDRESS can't be a constant.
Instead, #define it to be a variable, vm_max_kernel_address, just like we
do on sparc64.
Reviewed by: kib
Tested by: ian
is excessive. Postpone the flush of the fsinfo to VFS_SYNC(),
remembering the need for update with the flag MSDOSFS_FSIMOD, stored
in pm_flags.
FAT32 specification describes both FSI_Free_Count and FSI_Nxt_Free as
the advisory hints, not requiring them to be correct.
Based on the patch from bde, modified by me.
Reviewed by: bde
MFC after: 2 weeks
Microoptimize i8254 one-shot operation mode (disabled by default to allow
timecounter functionality) by not writing to mode and MSB registers when
it is not required. This saves several microseconds of CPU time per call,
reducing minimal measured interrupts interval to 19.5us.
points to the TLS in user space and points to the PCPU structure in
the kernel. The race is the result of having the exception handler on
the one hand and the RPC system call entry on the other. The EPC
syscall path is non-atomic in that interrupts are enabled while the
two stacks are switched. The register stack is switched last as that
is the stack used to determine whether we're going back to user space
by the exception handler. If we go back to user space, we restore r13,
otherwise we leave r13 alone. The EPC syscall path however set r13 to
the PCPU structure *before* switching the register stack, which means
that there was a window in which the exception handler would restore
r13 when it was already pointing to the PCPU structure. This is fatal
when the exception happened on CPU x, but left from the exception on
anotehr CPU. In that case r13 would point to the PCPU of the CPU the
thread was running on. This immediately results in getting the wrong
value for curthread.
The fix is to make sure we assign r13 *after* we set ar.bspstore to
point to the kernel register stack for the thread.
SDHCI driver
Suggested by: Daisuke Aoyama
- Set initilization sequence frequency to 8MHz. It should fix Data CRC
errors. Standard requires initialization sequence to be executed
at 400KHz but on this hardware low frequncies seems to cause
Data CRC errors.
Value was derived from analyzing hardware signals after
Raspberry Pi is powered up. Before any data is read though DATA line
adapter's clock frequency is changed to 8MHz.
Modern cards should function fine at 8MHz but for older MMC cards it
can be overriden by setting hw.bcm2835.sdhci.min_freq tunable.
- Replace divisor numbers with more descirptive names
- Properly calculate minimum frequency for SDHCI 3.0
- Properly calculate frequency for SDHCI 3.0 in mmcbr_set_clock
- Add min_freq method to sdhci_if.m and provide default
implementation. By re-implementing this method hardware
drivers can control frequency controller operates when
executing initialization sequence
