and update comments about original patches doing this and it not
working. It works for both the DL10019 and DL10022 based cards that I
have. It really helps the DL10019 cards, since they were using 8k
instead of the normal 16k that regular NE-2000 cards help.
# Note to self: need to provide a common routine to setup memory
# parameters.
DP8390-based cards have no generic way of reporting status of the link
or setting the media type. Some specific versions of these cards do,
however, allow for this, and we already support some of them. Make
the 'ed' experience more uniform by providing "autoselect" as the
meida and status "active" always. This won't affect the chips that
provide more specific details.
The DIROUT bit difference between the 19 and 22 is annoying. We can
set both bits on both parts without ill effect. Use this trick to
simplify the code.
The DELAYS in the MII bus bit-bang code for the DL100xx parts aren't
needed. Eliminate them.
packet data. However, the AX88190A moves this on-chip and reduces it
to the more traditional 16k from 16k-32k. The AX88790 follows the
'190A. Probe memory above 32k to see which flavor of the '190 we have
and use the extra memory if we have it.
Eliminate the kludgy read eeprom for the ID code. It really is just a
memory read at location 0x400, so just use that instead. Makes the
code easier to understand as well as eliminates some magic numbers.
ed cards. There's a number of minor nits in a lot of the PHYs on the
PC Cards that use the Axis AX88190 or DLink DL10019 and DL10022 chips.
Forcing the autonegotiation doesn't seem to cause problems on the
cards that have sane PHYs, but makes several cards I have work without
further workarounds.
I'm not 100% sure that kicking the PHY and resetting them is the right
thing to do on the media change callback. Other NICs seem to need
this and do similar things.
o Don't run through the register initialization in the read mac routine
for the AX88x90. It duplicates other stuff that we do.
o Eliminate the 10ms delay after we reset the AX88x90. We already wait for
the appropriate bits to indicate reset is done.
don't have one of the clock cycles (the turn cycle) that the AX88x90
chips have. Make this conditional. But this seems totally crazy and
can't possibly be right. Commit the fix for the moment until I can
explore this mystery more deeply.
On the plus side, the DL10022-based cards I have (D-Link DEF-670TXD
and SMC8040TX) work after this fix.
o Introduce new chip_type AX88790. There's a few places we need to know the
exact chip for workaronds.
o Explain the AX88190 workaround for the ISR bits being stuck, and don't
apply them to the AX88790. The datasheet says the bits are fixed, and
experience confirms.
o Fix mii bit-bang read code to read and discard the 'floating' bit.
o Remove empty ed_pccard_ax88x90_mii_reset routine
o Report error from mii_phy_probe
o Don't use ed_probe_Novel_generic for ax88x90 chips. It puts them into
an odd state sometimes. Instead, use a more stream-lined version that
avoids the trouble spots. This was copied and tweaked from the original.
o Move chip reset into its own routine.
o Minor code optimiation on getting MAC address
o Add code for coping with AX88790 cards that are in power down state and
need to be kicked before the PHY registers for the internal phy read right.
o Remove ugly cap of PHYs at 17.
o For AX88790, we need to set a special bit for accessig phy 16 (the internal
phy) and clear it for all others according to a chip erratum.
o streamline the bit-bang code for AX88x90: the delays aren't needed according
to the datasheet timing diagrams and also the Linux driver
o Fix minor bit definition for direction bit.
o Generally: Some comments reformatted
o Only try the toshiba probe on cards labelled as toshiba
# From another Akihabara card (this one from a few years ago from a
# friend in Japan). Fix the Corega FEther II PCC-TXD. This one is
# still on sale new, as of a few weeks ago. should fix all other AX88x90
# based cards, but I have some testing left to finish on my collection...
up) rather than amount + 1 / 2, which is the same as amount, or 2x too
many words which leads to data corruption.
# This fixes the sbdrop panics I was seeing with the Toshiba LANCT00A.
Toshiba PCETC ISA card, and even has the same board type code in the
card ID (0x14). So, for this card, call ed_probe_WD80x3_generic after
setting things up apropriately. This makes the card attach and kinda
work (I'm seeing panics in sbdrop). Since history has shown that the
WD80x3 probe routine is dangerous, only do it for this card. Also,
disable the memory range check to make sure it is an valid ISA memory.
I think that it is bogus, but I'm not 100% sure, for these cards.
I removed probing for the WD80x3 in 2005 when I added support for the
AX88x90 and DL100xx cards since none of my cards had ever matched it
and PAO3 removed it and none of the cards in their database died.
It is possible there are other quirks about this card too, since no
other open source OS supports it, or even claims to support it. But
it was a fun half hour hack...
driver. Not sure who sold it/rebadged it.
Add stub entries for Mitsubishi B8895 and Toshiba LANCT00A to the
driver with a comment that they don't work /* NG */.[*] These are
DP83902A based cards, which should work, but don't seem to. Likely
they are from the days before the ne2000 roamed the earth and use a
non-standard hookup (see if_ed_isa or if_ed_cbus for some examples).
Unless I happen to stumble into the right one, these may never work,
but I'm tired of omitting them from commits.
[*] The Japanese adopted OK from English, but also use NG for its
opposite.
would call ed_release_resources() when we should have called
ed_detach() to properly undo the effects of prior calls to
ed_attach(). This would leave a stray ed interface ifnet alive in the
system, which was, well, bad, since we called if_free() on the
underlying memory... Fix the ed_detach routine to cope being called
in this context now.
This should never come up because the miibus is always there. Except
for now when it seems to be failing for reasons unknown... That's a
different bug that hits at least ed, xl, dc and fxp...
o Implement a bunch of sysctl's to report the information
that's now always reported. Mvoe reporting of that info
to bootverbose, but maybe it can go away entirely.
dev.ed.X.type: string name
dev.ed.X.TxMem: amount of memory used for tx side of the card
dev.ed.X.RxMem: amount of memory used for rx side of the card
dev.ed.X.Mem: Total amount of mem on card.
o Better comments about where NE-2000 (and clones) gets their MAC
address from.
The ed driver on pc98 was broken by if_edvar.h rev1.31.
Reported by: Kaho Toshikazu (kaho at elam kais kyoto-u ac jp)
Tested by: Eiji Kato (ekato at a1 mbn or jp)
MFC after: 3 days
into the card's memory.
# this eliminates a more of the ifdef soup in if_ed and if_edvar
# I've fixed the cbus drivers, but can't test them all easily.
If I've broken anything, please let me know.
to properly configure the right interface to use.
Also call the mediachg function when we set flags UP and are already
running. If this were a pure ifmedia driver, we'd not need to do this
since we'd be ignoring the linkX flags.
This reduces the number of ifdefs to support sub-devices a little as a
nice side effect. It also reduces the number of hpp interfaces
exposed by 33%.
man page that the ifconfig option link2 is used to disable the AUI
transceiver on the 3com boards (should also say HP PC Lan+). This
makes the connection clearer.
Add a note about why we set this flag prior to attaching the device.
We never set or clear the flag later, only test it. There can be no
races here, but this might be asthetically displeasing to some. Also
note that we may no longer need to have this knob at all as we may be
able to do it with the more sophisticated rc.d scripts we have today I
think the only reason it is there is because we didn't used to allow
its proper setting when configured to get the IP address via DHCP.
I'll note that this would be better handled by using ifmedia for all
ed cards, not just those with a miibus...
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
