list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
and BeOS. The devices supported by uslcom(4) are now in sync with:
NetBSD src/sys/dev/usb/uslsa.c 1.11
OpenBSD src/sys/dev/usb/uslcom.c 1.20
Linux source/drivers/usb/serial/cp210x.c from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Two vendor/product IDs from Linux have not been added to uslcom(4):
SILABS SAEL - This device has special code in u3g to support it
SILABS GSM2228 - I suspect this should also be covered by u3g(4).
MFC after: 1 week
vendor ID in the vendor section, and by symbolic name in the product
section. Products are sorted by product ID. While here, get rid of a
duplicate Microsoft Mouse entry, revealed by sorting.
MFC after: 1 week
the official vendor listed for 0x076b, rather than Omnikey, as in the PR.
PR: usb/123351
Submitted by: Marcin Cieslak <saper SYSTEM.PL>
MFC after: 1 week
This patch is different to that provided in the PR, due to the changes in
this driver since 7.x.
PR: usb/129945
Submitted by: Antonio Hilario <avahilario gmail.com>
MFC after: 1 week
- Bring in several other devices from OpenBSD while here. Use the
official manufacturer name over the OpenBSD name in the case of
GEMALTO. Reorder list slightly to aid future syncing.
- Remove duplicate SILABS CP2102 define from usbdevs
PR: usb/131912 [1]
Submitted by: Jack Twilley <mathuin gmail.com> [1]
MFC after: 1 week
plug. Note that the Vendor ID 0x04b4 is officially assigned to Cypress,
so use that instead of adding a second vendor with an identical ID, in the
same way other similar cases are treated in usb/usbdevs.
PR: usb/132785
Submitted by: Dirk-Willem van Gulik <dirkx webweaving.org>
MFC after: 1 week
- Fixed the interface probe routine to only attach to USB interfaces the driver
actually supports. This allows other drivers to attach to things like
MicroSD slots etc.
- Fixed network interface enumeration to be globally sequential instead of
relying on the USB interface numbers. This make sure the first network
interface always is at uhso0 and the second at usho1 and so on.
- Added a radio kill switch; exposed through sysctl.
- Updated the manual page to be verbose about the number of serial ports and
include iCON 452 in the set of tested hardware.
Submitted by: Fredrik Lindberg
The driver is stub. It just creates device entry and feeds
reassembled packets from hardware into it.
If in future we would port wsmouse(4) from NetBSD, or make
sysmouse(4) to support absolute motion events, then the driver
can be extended to act as system mouse. Meanwhile, it just
presents a /dev/uep0, that can be utilized by X driver, that
I am going to commit to ports tree soon.
The name for the driver is chosen to be the same as in NetBSD,
however, due to different USB stacks this driver isn't a port.
from standard 3G wireless units by supplying a raw IP/IPv6 endpoint rather than
using PPP over serial. uhsoctl(1) is used to initiate and close the WAN
connection.
Obtained from: Fredrik Lindberg <fli@shapeshifter.se>
