Nominal Mhz is either expressed via the clock-frequency property
or can be get via the clock property that holds the cpu clock.
Add support for the later.
Reviewed by: nwhitehorn
Differential Revision: https://reviews.freebsd.org/D16346
The nvmem interface helps provider of nvmem data to expose themselves to consumer.
NVMEM is generally present on some embedded board in a form of eeprom or fuses.
The nvmem api are helpers for consumer to read/write the cell data from a provider.
Differential Revision: https://reviews.freebsd.org/D16419
The buffer descriptor list entries should be in little endian format. Byte swap
them on BE. This is the last piece of the puzzle for snd_hda(4) to work on
PowerPC.
This calls into the Arm Trusted Firmware to enable and disable the
workaround for the Speculative Store Bypass Disable (SSBD) issue, also
known as Spectre Variant 4.
As this may have a large performance overhead, and how exploitable SSBD is
is unknown we follow the Linux lead of allowing the administrator to select
between always on, always off, or only enabled in the kernel, with the
latter being the default.
PR: 228955
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D15819
The CORB and RIRB buffers exist in DMA memory, but the device reads them as
little-endian only. Read and write as LE into the DMA memory block, to work on
BE platforms.
The latter matches the rest of the tree better [0]. The UPDATING entry has
been updated to reflect this, and the new tunable is now documented in
loader(8) [1].
Reported by: imp [0], Shawn Webb [1]
Leading up to enabling EFIRT in GENERIC, allow runtime services to be
disabled with a new tunable: efi.rt_disabled. This makes it so that EFIRT
can be disabled easily in case we run into some buggy UEFI implementation
and fail to boot.
Discussed with: imp, kib
MFC after: 1 week
The timespecadd(3) family of macros were imported from NetBSD back in
r35029. However, they were initially guarded by #ifdef _KERNEL. In the
meantime, we have grown at least 28 syscalls that use timespecs in some
way, leading many programs both inside and outside of the base system to
redefine those macros. It's better just to make the definitions public.
Our kernel currently defines two-argument versions of timespecadd and
timespecsub. NetBSD, OpenBSD, and FreeDesktop.org's libbsd, however, define
three-argument versions. Solaris also defines a three-argument version, but
only in its kernel. This revision changes our definition to match the
common three-argument version.
Bump _FreeBSD_version due to the breaking KPI change.
Discussed with: cem, jilles, ian, bde
Differential Revision: https://reviews.freebsd.org/D14725
It's easy to confuse the error code as naked it looks decimal (EINVAL is
reported as error 16, instead of error 22, so first reading looks like EBUSY).
This fixes the panic caused by deadlocking when grant-table free
callbacks are used.
The cause of the recursion is: check_free_callbacks() is always called
with the lock gnttab_list_lock held. In turn the callback function is
also called with the lock held. Then when the client uses any of the grant
reference methods which also attempt the lock the gnttab_list_lock
mutex from within the free callback a deadlock happens.
Fix this by making the gnttab_list_lock recursive.
Submitted by: Pratyush Yadav <pratyush@freebsd.org>
Differential Revision: https://reviews.freebsd.org/D16505
If gnttab_grant_foreign_access() fails for any of the indirection
pages, the code breaks out of both the loops without freeing the local
variable indirectpages, causing a memory leak.
Submitted by: Pratyush Yadav <pratyush@freebsd.org>
Differential Review: https://reviews.freebsd.org/D16136
Length is an unsigned integer, so checking against < 0 doesn't make
sense. While there also make clear that a length of 0 always succeeds.
Submitted by: Pratyush Yadav <pratyush@freebsd.org>
Differential Review: https://reviews.freebsd.org/D16045
Ifuncs selectors dispatch copyin(9) family to the suitable variant, to
set rflags.AC around userspace access. Rflags.AC bit is cleared in
all kernel entry points unconditionally even on machines not
supporting SMAP.
Reviewed by: jhb
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D13838
r336773 removed all things xscale. However, some things xscale are
really armv5. Revert that entirely. A more modest removal will follow.
Noticed by: andrew@
The OLD XSCALE stuff hasn't been useful in a while. The original
committer (cognet@) was the only one that had boards for it. He's
blessed this removal. Newer XSCALE (GUMSTIX) is for hardware that's
quite old. After discussion on arm@, it was clear there was no support
for keeping it.
Differential Review: https://reviews.freebsd.org/D16313
The last known robust version of this code base was FreeBSD 8.2. There
are no users of this on current, and all users of it have abandoned
this platform or are in legacy mode with a prior version of FreeBSD.
All known users on arm@ approved this removal, and there were no
objections.
Differential Revision: https://reviews.freebsd.org/D16312
There were some bits that were being set in cmd_flags (a field of AHCI's
command list structure) after cmd_flags was converted to little endian.
On a big endian host, such as PowerPC, this would set the wrong bits.
This was preventing AHCI driver from working on these hosts.
Reviewed by: jhibbits
Approved by: jhibbits (mentor)
Start in "class" instead of "flow" mode. This eliminates the need to
specify an MTU, which is not available that early anyway. It also
allows the user to manually configure ch-rl rate limiting after attach.
This used to fail because ch-rl isn't supported if cl-rl "flow" mode is
configured.
Set all traffic classes to 1Gbps during initialization. The goal is to
start off with _any_ valid configuration and 1Gbps works even for
gigabit cards.
Sponsored by: Chelsio Communications
jedec_dimm(4) is a superset of the functionality of jedec_ts(4). Mark
jedec_ts(4) as removed in FreeBSD 12, and include a pointer to the migration
instructions in the jedec_dimm(4) manpage, in both the jedec_ts(4) code and
the jedec_ts(4) manpage. Add a note to the jedec_dimm(4) manpage about the
fact that it is a superset of jedec_ts(4).
This change will be MFCed to stable/11 and stable/10; the followup change
to actually remove jedec_ts(4) from -HEAD will not.
Reviewed by: avg
MFC after: 1 week
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D16412
This change allows one to set the busy_detect flag
required by the synopsys UART at the loader prompt.
This is needed by the EPYC 3000 SoC.
This will give users a working console up to the point where getty is required:
hw.uart.console="mm:0xfedc9000,rs:2,bd:1"
Reviewed by: imp
MFC after: 4 weeks
Differential Revision: https://reviews.freebsd.org/D16399
- Don't bother calling if_setbaudrate(9) as iflib_link_state_change(9)
takes care of that,
- correctly check for E1000_CTRL_EXT_LINK_MODE_GMII in E1000_CTRL_EXT [1],
- properly convert the uint16_t link_speed to a uint64_t baudrate by
using IF_Mbps() which contains an appropriate cast [2],
- remove the duplicate link down announcement when bootverbose isn't
zero and bring the remaining one in line with the other link state
messages.
o Remove a dead store to rid in em_if_msix_intr_assign(). [3]
o Or in the DMA coalescing Rx threshold so the other bits set in E1000_DMACR
remain intact as intended in igb_init_dmac(). [4]
Reported by: Coverity
CID: 1378464 [1], 1368765 [2], 1381681 [3], 1304929 [4]
This fixes usage/report size calculation of Microsoft`s "Touch Hardware
Quality Assurance" certificate blob found in many touchscreens.
While here, join several "c->flags = dval" lines in to single line.
Reviewed by: hselasky
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D16357
/chosen/stdout-path is a string, not ihandle. Treat it as such.
With this, ofwfb now starts correctly on a POWER9 system when launched from
the local console (not serial).
The FDT implementation of OF_instance_to_package() backend checks the
cross-reference to get the node. On failure, this returns the input handle
unchanged. In the case of ofwfb attachment, if /chosen/stdout property does not
exist, sc->sc_handle is either garbage or 0, which then gets propagated to node.
This will prevent "screen" from being used, resulting in not properly attaching.
Correct this by matching the code in ofwfb_probe().
Oppv2 add more flexibility on regulator value for the core voltage amongst
other new thing.
For now only shared opp table is supported as I don't have hardware with
non-shared opp table.
Tested-On: OrangePi One (with oppv1 and oppv2)
Tested-On: Pine64-LTS
When booted as PVHv2, there's no ACPI CPU object, so attach the PV CPU
device in order to take it's place.
This is required in case some device or driver tries to poke at the
PCPU device field.
Sponsored by: Citrix Systems R&D
HYPERVISOR_start_info is only available to PV and PVHv1 guests, HVM
and PVHv2 guests get this data from HVM parameters that are fetched
using a hypercall.
Instead provide a set of helper functions that should be used to fetch
this data. The helper functions have different implementations
depending on whether FreeBSD is running as PVHv1 or HVM/PVHv2 guest
type.
This helps to cleanup generic Xen code by removing quite a lot of
xen_pv_domain and xen_hvm_domain macro usages.
Sponsored by: Citrix Systems R&D
found in some MacBook Pro.
PR: 229727
Reported by: Stephan Neuhaus <sten@artdecode.de> and others
Tested by: Stephan Neuhaus <sten@artdecode.de>
Approved by: mav (mentor)
MFC after: 1 month
Query the minimal inline mode supported by the card.
When creating a send queue, cache the queried mode and optimize the transmit
if no inlining is required. In this case, we can avoid touching the headers
cache line and avoid dirtying several more lines by copying headers into
the send WQEs. Also, if no inline headers are used, hardware assists in
the VLAN tag framing.
Submitted by: kib@, slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Issue: IO fails immediately after doing port-toggle.
Fix: Added LDT(Device Lost Timer)- we wait a specific period of time prior to telling the OS about lost device.
Approved by: ken, mav
MFC after: 3 days
Differential Revision: D16196
Track session objects in the framework, and pass handles between the
framework (OCF), consumers, and drivers. Avoid redundancy and complexity in
individual drivers by allocating session memory in the framework and
providing it to drivers in ::newsession().
Session handles are no longer integers with information encoded in various
high bits. Use of the CRYPTO_SESID2FOO() macros should be replaced with the
appropriate crypto_ses2foo() function on the opaque session handle.
Convert OCF drivers (in particular, cryptosoft, as well as myriad others) to
the opaque handle interface. Discard existing session tracking as much as
possible (quick pass). There may be additional code ripe for deletion.
Convert OCF consumers (ipsec, geom_eli, krb5, cryptodev) to handle-style
interface. The conversion is largely mechnical.
The change is documented in crypto.9.
Inspired by
https://lists.freebsd.org/pipermail/freebsd-arch/2018-January/018835.html .
No objection from: ae (ipsec portion)
Reported by: jhb
1. Fix taskqueues drain/free to fix panic seen when interface is being
bought down and in parallel asynchronous link events happening.
2. Fix bxe_ifmedia_status()
Submitted by:Vaishali.Kulkarni@cavium.com and Anand.Khoje@cavium.com
MFC after:5 days
