Not only did these two drivers depend on IFF_NEEDSGIANT, they were
broken 7 months ago during the MPSAFE TTY import. if_ppp(4) has been
replaced by ppp(8). There is no replacement for if_sl(4).
If we see regressions in for example the ports tree, we should just use
__FreeBSD_version 800045 to check whether if_ppp(4) and if_sl(4) are
present. Version 800045 is used to denote the import of MPSAFE TTY.
Discussed with: rwatson, but also rwatson's IFF_NEEDSGIANT emails on the
lists.
- add support for more complicated HID descriptors which can have multiple
definitions of the same field.
- remove old modulo patch in ums, which I think is due to bad HID parsing,
which should be fixed now.
Reported by: netchild
Submitted by: Hans Petter Selasky
at91_udp.c does not exist anymore, it is now replaced by at91dci in
src/sys/dev/usb/controller. Also remove the ohci_atmelarm.c because it is also
included in src/sys/conf/files
Submitted by: Sylvestre Gallon
Some cancelable flags are always true. Substitute these away. These cancelable
flags were mostly useful with the root HUB which is now handled differently.
Submitted by: Hans Petter Selasky
Refactor how we interface with the root HUB. This cuts around 1200 lines of
code totally and saves one thread per USB bus.
Submitted by: Hans Petter Selasky
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
- bugfixes after the memory usage reduction patch
- Use "udev->pipes_max" instead of USB_EP_MAX
- Use correct "bmRequestType" for getting the config descriptor.
Submitted by: Hans Petter Selasky
- memory usage reduction by only allocating the required USB pipes and USB
interfaces.
- cleanup some USB parsing functions to be more flexible.
Submitted by: Hans Petter Selasky
1) Move the new field (brand_note) to the end of the Brandinfo structure.
2) Add a new flag BI_BRAND_NOTE that indicates that the brand_note pointer
is valid.
3) Use the brand_note field if the flag BI_BRAND_NOTE is set and as old
modules won't have the flag set, so the new field brand_note would be
ignored.
Suggested by: jhb
Reviewed by: jhb
Approved by: kib (mentor)
MFC after: 6 days
but I see no benefit from it today.
VM_PROT_READ_IS_EXEC was only intended for use on processors that do not
distinguish between read and execute permission. On an mmap(2) or
mprotect(2), it automatically added execute permission if the caller
specified permissions included read permission. The hope was that this
would reduce the number of vm map entries needed to implement an address
space because there would be fewer neighboring vm map entries that differed
only in the presence or absence of VM_PROT_EXECUTE. (See vm/vm_mmap.c
revision 1.56.)
Today, I don't see any real applications that benefit from
VM_PROT_READ_IS_EXEC. In any case, vm map entries are now organized
as a self-adjusting binary search tree instead of an ordered list. So,
the need for coalescing vm map entries is not as great as it once was.
being switched out may hold a reservation. The stwcx. will
clear the reservation. This is architecturally recommended.
The scenario this addresses is as follows:
1. Thread 1 performs a lwarx and as such holds a reservation.
2. Thread 1 gets switched out (before doing the matching
stwcx.) and thread 2 is switched in.
3. Thread 2 performs a stwcx. to the same reservation granule.
This will succeed because the processor has the reservation
even though thread 2 didn't do the lwarx.
Note that on some processors the address given the stwcx. is
not checked. On these processors the mere condition of having
a reservation would cause the stwcx. to succeed, irrespective
of whether the addresses are the same. The dummy stwcx. is
especially important for those processors.
- Fix style for A3N and for a comment
Submitted by: Akira Funahashi <funa@funa.org>
Tested by: Marcin Nowak <marcin.nowak@simplusnet.pl>,
Diego Sardina <diego.sardina@gmx.com>
PR: kern/128634
in the case where a single mbuf is allocated due to
m_getcl() returning NULL, we already call MH_ALIGN,
so do not increment m->m_data in this case.
Found during MLDv2 port.
The later may need blocks from the underlying device that belongs
to normal files, that should not be locked while snap lock is held.
Reported and tested by: pho
MFC after: 1 month
- PR-SCTP had major issues when skipping through a multi-part message.
o Did not look at socket buffer.
o Did not properly handle the reassmebly queue.
o The MARKED segments could interfere and un-skip a chunk causing
a problem with the proper FWD-TSN.
o No FR of FWD-TSN's was being done.
- NR-Sack code was basically disabled. It needed fixes that
never got into the real code.
- CMT code had issues when the two paths were NOT the same b/w. We
found a few small bugs, but also the critcal one here was not
dividing the rwnd amongst the paths.
Obtained from: Michael Tuexen and myself at the IETF hack-fest ;-)
on a generic dumper that creates an ELF core file and
uses PMAP functions to scan and iterate over memory
chunks, as well as handle memory mappings used during
dumping.
the PMAP layer can choose to return physical memory
chunks or virtual memory chunks. For minidumps, the
chunks should be virtual.
The default MMU I/F implementation for the scan_md()
method returns NULL. Thus, when a PMAP implementation
does not implement the required methods, an empty
core file is created. Here, empty means having an ELF
header only.
Obtained from: Juniper Networks
the ATA status register with a 4-byte read request. This updates it, and
subsequent 1-byte reads will return the correct result.
This commit adds a hack to do this, which is currently ifdef'd powerpc,
although Linux and Darwin do this unconditionally on all platforms.
provided, for example, on the PowerPC 970 (G5), as well as on related CPUs
like the POWER3 and POWER4.
This also adds support for various built-in hardware found on Apple G5
hardware (e.g. the IBM CPC925 northbridge).
Reviewed by: grehan
