This forces a full reset of the baseband/radio and seems needed to clear
some issues (with Merlin at least) when the baseband gets confused in a
very noisy environment.
Sponsored by: Hobnob, Inc.
RX clear, RX extension clear.
This is useful for estimating channel business.
The same routines should be written for AR5210->AR5212 where appopriate.
Obtained from: Atheros
some unmerged interrupt status debugging code from my branch.
* Add ah_intrstate[8] which will have the record of the last
call to ath_hal_getintr().
* Wrap the KTR code behind ATH_KTR_INTR_DEBUG.
* Add the HAL interrupt debugging behind AH_INTERRUPT_DEBUGGING.
This is only done for the AR5416 and later NICs but it will be
trivial to add to the earlier NICs if required.
Neither are enabled by default, although to minimise HAL binary
API differences, the ah_intrstate[] array is always compiled into
the ath_hal struct.
for Atheros AR5416 and later wireless devices.
This is a very large commit - the complete history can be
found in the user/adrian/if_ath_tx branch.
Legacy (ie, pre-AR5416) devices also use the per-software
TXQ support and (in theory) can support non-aggregation
ADDBA sessions. However, the net80211 stack doesn't currently
support this.
In summary:
TX path:
* queued frames normally go onto a per-TID, per-node queue
* some special frames (eg ADDBA control frames) are thrown
directly onto the relevant hardware queue so they can
go out before any software queued frames are queued.
* Add methods to create, suspend, resume and tear down an
aggregation session.
* Add in software retransmission of both normal and aggregate
frames.
* Add in completion handling of aggregate frames, including
parsing the block ack bitmap provided by the hardware.
* Write an aggregation function which can assemble frames into
an aggregate based on the selected rate control and channel
configuration.
* The per-TID queues are locked based on their target hardware
TX queue. This matches what ath9k/atheros does, and thus
simplified porting over some of the aggregation logic.
* When doing TX aggregation, stick the sequence number allocation
in the TX path rather than net80211 TX path, and protect it
by the TXQ lock.
Rate control:
* Delay rate control selection until the frame is about to
be queued to the hardware, so retried frames can have their
rate control choices changed. Frames with a static rate
control selection have that applied before each TX, just
to simplify the TX path (ie, not have "static" and "dynamic"
rate control special cased.)
* Teach ath_rate_sample about aggregates - both completion and
errors.
* Add an EWMA for tracking what the current "good" MCS rate is
based on failure rates.
Misc:
* Introduce a bunch of dirty hacks and workarounds so TID mapping
and net80211 frame inspection can be kept out of the net80211
layer. Because of the way this code works (and it's from Atheros
and Linux ath9k), there is a consistent, 1:1 mapping between
TID and AC. So we need to ensure that frames going to a specific
TID will _always_ end up on the right AC, and vice versa, or the
completion/locking will simply get very confused. I plan on
addressing this mess in the future.
Known issues:
* There is no BAR frame transmission just yet. A whole lot of
tidying up needs to occur before BAR frame TX can occur in the
"correct" place - ie, once the TID TX queue has been drained.
* Interface reset/purge/etc results in frames in the TX and RX
queues being removed. This creates holes in the sequence numbers
being assigned and the TX/RX AMPDU code (on either side) just
hangs.
* There's no filtered frame support at the present moment, so
stations going into power saving mode will simply have a number
of frames dropped - likely resulting in a traffic "hang".
* Raw frame TX is going to just not function with 11n aggregation.
Likely this needs to be modified to always override the sequence
number if the frame is going into an aggregation session.
However, general raw frame injection currently doesn't work in
general in net80211, so let's just ignore this for now until
this is sorted out.
* HT protection is just not implemented and won't be until the above
is sorted out. In addition, the AR5416 has issues RTS protecting
large aggregates (anything >8k), so the work around needs to be
ported and tested. Thus, this will be put on hold until the above
work is complete.
* The rate control module 'sample' is the only currently supported
module; onoe/amrr haven't been tested and have likely bit rotted
a little. I'll follow up with some commits to make them work again
for non-11n rates, but they won't be updated to handle 11n and
aggregation. If someone wishes to do so then they're welcome to
send along patches.
* .. and "sample" doesn't really do a good job of 11n TX. Specifically,
the metrics used (packet TX time and failure/success rates) isn't as
useful for 11n. It's likely that it should be extended to take into
account the aggregate throughput possible and then choose a rate
which maximises that. Ie, it may be acceptable for a higher MCS rate
with a higher failure to be used if it gives a more acceptable
throughput/latency then a lower MCS rate @ a lower error rate.
Again, patches will be gratefully accepted.
Because of this, ATH_ENABLE_11N is still not enabled by default.
Sponsored by: Hobnob, Inc.
Obtained from: Linux, Atheros
preparation for TX aggregation.
* Add in logic which calls ath_buf bf->bf_comp if it's set.
This allows for AMPDU (and RIFS, and FF, if someone desires) code
to handle completion - which includes freeing subframes, retransmitting
subframes, etc.
* Break out the buffer free, buffer busy/unbusy default completion handler
code into separate functions. This allows bf_comp methods to free and
unbusy each subframe ath_buf as required.
* Break out the statistics update code into a separate function, just
to clean up the TX completion path a little.
Sponsored by: Hobnob, Inc.
descriptor, rather than using the maths involving bf_desc[bf_nseg - 1].
When doing TX aggregation, the status will be updated in the -final-
descriptor of the -final- subframe in an aggregate. Thus bf_lastds
may point to the last descriptor in a completely different ath_buf.
Sponsored by: Hobnob, Inc.
* Immediately return NULL if a buffer isn't available;
* Track the "buffers not available" count;
* Clear some fields used for tx aggregation;
* Add ath_buf_clone() which clones the majority of buffer state.
This is needed when retransmission of a "busy" buffer is required.
Sponsored by: Hobnob, Inc.
Add some code (which is currently disabled) which modifies the group
multicast key cache behaviour. I haven't yet figured out what the
exact/correct behaviour is so I'm leaving it disabled. It's worth
investigating and "correcting", especially for future work with
mesh/ibss and encryption.
Sponsored by: Hobnob, Inc.
* When doing software TX queue handling and flush, it's possible
that the deletion of a VAP (eg a STA shutdown) will queue a
"STA Disassociate" frame whilst the interface is being deleted.
The VAP is then deleted, and the frame ends up being queued
to a node that is freed before it can be TX'ed. Things go awry
at this point.
There's no way at the present to avoid freeing the underlying node
when the vap is being deleted. It's too late in the game.
I suspect the real fix is to make sure the frame is software
queued with no completion information somehow, so it doesn't
link back to a node whose underlying VAP has been freed.
For now, we'll just have to do this.
* Add some comments showing what's going on.
* Move an instance of the ATH_LOCK() around to protect the interrupt
set. I'll worry about changing that to a PCU lock later on once
the 11n code is in the tree.
Sponsored by: Hobnob, Inc.
and interface resets to be marked as ATH_RESET_DEFAULT, ATH_RESET_FULL,
ATH_RESET_NOLOSS.
Currently a reset is still a reset - ie, all tx/rx frames in the hardware
queues are purged. This means that those frames will be lost to the 11n TX
and RX aggregation state tracking, breaking AMPDU sessions.
The (eventual) new semantics:
* ATH_RESET_DEFAULT:
full reset, this is the default for reset situations
which I haven't yet figured out what they should be.
* ATH_RESET_FULL:
A full reset - for things such as channel changes.
* ATH_RESET_NOLOSS:
Don't flush TX/RX queues - handle pending RX frames and leave TX
frames where they are; restart TX DMA from where it was.
* Change ath_rx_proc() to ath_rx_tasklet(); make that the taskqueue function.
This way (eventually) ath_rx_proc() can be called from elsewhere in the
packet reset/processing queue so frames aren't just "flushed" during
interface resets/reconfigure. This breaks 802.11n RX aggregation tracking.
* Extend ath_tx_proc() to take a 'resched' flag, which marks whether to
reschedule further RX PCU reads or not.
* Change ath_tx_processq() to take a "dosched" flag, which will eventually
be used to indicate whether to reschedule the software TX scheduler.
Sponsored by: Hobnob, Inc.
allocator with UMA backed jumbo allocator by default. Previously
ti(4) used sf_buf(9) interface for jumbo buffers but it was broken
at this moment such that enabling jumbo frame caused instant panic.
Due to the nature of sf_buf(9) it heavily relies on VM changes but
it seems ti(4) was not received much blessing from VM gurus. I
don't understand VM magic and implications used in driver either.
Switching to UMA backed jumbo allocator like other network drivers
will make jumbo frame work on ti(4).
While I'm here, fully allocate all RX buffers. This means ti(4) now
uses 512 RX buffer and 1024 mini RX buffers.
To use sf_buf(9) interface for jumbo buffers, introduce a new
'options TI_SF_BUF_JUMBO'. If it is proven that sf_buf(9) is better
for jumbo buffers, interesting developers can fix the issue in
future.
ti(4) still needs more bus_dma(9) cleanups and should use separate
DMA tag/map for each ring(standard, jumbo, mini, command, event
etc) but it should work on all platforms except PAE.
Special thanks to Jay[1] who provided complete remote debugging
access.
Tested by: Jay Borkenhagen <jayb <> braeburn dot org > [1]
* Close down some of the kickpcu races, where the interrupt handler
can and will run concurrently with the taskqueue.
* Close down the TXQ active/completed race between the interrupt
handler and the concurrently running tx completion taskqueue
function.
* Add some tx and rx interrupt count tracking, for debugging.
* Fix the kickpcu logic in ath_rx_proc() to not simply drain and
restart the TX queue - instead, assume the hardware isn't
(too) confused and just restart RX DMA. This may break on
previous chipsets, so if it does I'll add a HAL flag and
conditionally handle this (ie, for broken chipsets, I'll
just restore the "stop PCU / flush things / restart PCU"
logic.)
* Misc stuff
Sponsored by: Hobnob, Inc.
A bunch of the 11n TX aggregation logic wants to traverse lists of buffers
in various ways. In order to provide O(1) behaviour in this instance,
use TAILQs.
This does blow out the memory footprint and CPU cycles slightly for some
of these operations. I may convert some of these back to STAILQs once
the rest of the software transmit queue handling has been stabilised.
Sponsored by: Hobnob, Inc.
* Use 64 bit integer types for the sample rate statistics.
When TX'ing 11n aggregates, a 32 bit counter will overflow in a few
hours due to the high packet throughput.
* Create a default label of "" rather than defaulting to "Mb" - that way
if a rate hasn't yet been selected, it won't say "-1 Mb".
Sponsored by: Hobnob, Inc.
* Add a PCU lock, which isn't currently used but will eventually be
used to serialise some of the driver access.
* Add in all the software TX aggregation state, that's kept per-node
and per-TID.
* Add in the software and aggregation state to ath_buf.
* Add in hooks to ath_softc for aggregation state and the (upcoming)
aggregation TX state calls.
* Add / fix the HAL access macros.
Obtained from: Linux, ath9k
Sponsored by: Hobnob, Inc.
o Do not blindly UP controller when MTU is changed. Reinitialize
controller only if driver is running.
o Remove useless ti_stop() in ti_watchdog() since ti_init_locked()
always invokes ti_stop().
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
checksum offloading and VLAN hardware tag insertion/stripping from
the currently enabled hardware offloading capabilities.
Previously if_hwassist, which was initialized to TX/RX checksum
offloading, was blindly used to enable both TX and RX checksum
offloading such that disabling either TX or RX checksum offloading
was not possible.
ti(4) controllers support TX/RX checksum offloading with VLAN
tagging so announce TX/RX checksum offloading capability over VLAN
to vlan(4).
Make VLAN hardware tag insertion/stripping honors currently enabled
interface capability instead of blindly enabling VLAN hardware
tagging. This change allows disabling hardware support of VLAN tag.
Because ti(4) supports VLAN oversized frames, make network stack
know the capability by setting if_hdrlen.
While I'm here, rewrite SIOCSIFCAP handler and make sure to
reinitialize controller whenever TX/RX checksum offloading and VLAN
hardware tagging option is changed. The requirement of controller
reinitialization comes from the limitation of Tigon I/II firmware.
Tigon I/II firmware requires all related RCBs should be
reinitialized whenever any of its hardware offloading capabilities
change.
vlan(4) is also notified whenever the parent interface's capability
changes such that it can correctly handle TX/RX checksum offloading
based on parent interface's enabled offloading capabilities.
RX checksum offloading handler was changed to make upper stack use
controller computed partial checksum value. Previously, ti(4) just
set the computed value for any frames(IPv4, IPv6) and the value was
not used in upper stack because driver didn't set CSUM_DATA_VALID
such that upper network stack had to recompute checksum of TCP/UDP
packets. I have no idea how this was not noticed for a long time.
With this change, upper network stack does not have to fully
recompute the checksum such that calculating pseudo checksum based
on partial checksum is sufficient to know whether received packet's
checksum is correct or not. However, I don't know why ti(4) does
not have controller compute pseudo checksum as controller has
ability to do it. I'm just guessing enabling that feature could
trigger a firmware bug or could be slower than computing it on host
side so just leave it as it was.
In order not to produce false positives, ti(4) now checks whether
controller actually computed IP or TCP/UDP checksum by checking
ti_flags field.
state changes. Hide superfluous link up/down message under
bootverbose since if_link_state_change(9) shows that information.
While I'm here, change baudrate with the resolved speed of the
established link instead of blindly setting it 1G. Unfortunately,
it seems there is no way to differentiate 10/100Mbps from
non-gigabit link so just assume we established a 100Mbps link if
current link is not a gigabit link.
