in the actual _FDE parsing. If the failure occurs earlier such as in
fdc_attach() then don't try to probe any drives.
MFC after: 3 days
Reviewed by: njl
Tested by: Christian Laursen xi at borderworlds dot dk
driver. Trim its fingernails by removing some useless bits before
fixing the 'thread not terminated on detach' problem.
o dmacnt is no longer used now that we allocate at attach time. Remove
it from struct fdc_data.
o ISPNP was only ever set, but never tested. It used to be used for the
allocation routines to change how it allocated resources. Since that's
no longer necessary, retire the flag.
o ISPCMICA was only ever tested, but never set. GC it. This removes
a special case in determining the drive type. The drive type is
now set in fdc_pcmcia.c, so the hack isn't needed anymore. Sadly,
this isn't tested with a Y-E Data pcmcia floppy drive because there
are a number of other issues that preclude it from working.
o Fix ifdef for reading from the rtc. I'm of the opinion that this ifdef
should be moved into fdc_isa.c, but not today as ideally there'd be
other fixes to the probing of children. So now we just read it on
i386 ! pc98 (there's no #define for MACHINE_ARCH, just MACHINE, hence
this slightly inelegant kludge) and amd64. The PC98 exclusion likely
isn't meaningful since pc98 uses a different driver, but will be when
merging of the pc98 floppy code into this driver is complete (this is the
other reason I think this block of code belongs outside fdc.c).
All of these changes are safe to MT5.
another way to misinterpret the spec. Also, always fall back to the hints
probe on any attach failure, not just when _FDE fails.
Thanks to imp and scottl for finding this.
Tested by: rwatson (minimally)
MFC after: 5 days
errors for the attachment process for the floppy controller. This is
a band-aide because it doesn't try any of the fallback methods when
_FDE isn't long enough, but should be sufficient for people
experiencing the dreaded mutex not initialized panic.
the old one is. Hence we need to evaluate the old one for _FDI since it
has a valid ACPI_HANDLE ivar. This is a minimal fix. Make a note that a
more complete one is to make fdc support the ACPI_HANDLE ivar for its
children.
This and the previous change are MT5 candidates.
Centralize the fdctl_wr() function by adding the offset in
the resource to the softc structure.
Bugfix: Read the drive-change signal from the correct place:
same place as the ctl register.
Remove the cdevsw{} related code and implement a GEOM class.
Ditch the state-engine and park a thread on each controller
to service the queue.
Make the interrupt FAST & MPSAFE since it is just a simple
wakeup(9) call.
Rely on a per controller mutex to protect the bioqueues.
Grab GEOMs topology lock when we have to and Giant when
ISADMA needs it. Since all access to the hardware is
isolated in the per controller thread, the rest of the
driver is lock & Giant free.
Create a per-drive queue where requests are parked while
the motor spins up. When the motor is running the requests
are purged to the per controller queue. This allows
requests to other drives to be serviced during spin-up.
Only setup the motor-off timeout when we finish the last
request on the queue and cancel it when a new request
arrives. This fixes the bug in the old code where the motor
turned off while we were still retrying a request.
Make the "drive-change" work reliably. Probe the drive on
first opens. Probe with a recal and a seek to cyl=1 to
reset the drive change line and check again to see if we
have a media.
When we see the media disappear we destroy the geom provider,
create a new one, and flag that autodetection should happen
next time we see a media (unless a specific format is configured).
Add sysctl tunables for a lot of drive related parameters.
If you spend a lot of time waiting for floppies you can
grab the i82078 pdf from Intels web-page and try tuning
these.
Add sysctl debug.fdc.debugflags which will enable various
kinds of debugging printfs.
Add central definitions of our well known floppy formats.
Simplify datastructures for autoselection of format and
call the code at the right times.
Bugfix: Remove at least one piece of code which would have
made 2.88M floppies not work.
Use implied seeks on enhanced controllers.
Use multisector transfers on all controllers. Increase
ISADMA bounce buffers accordingly.
Fall back to single sector when retrying. Reset retry count
on every successful transaction.
Sort functions in a more sensible order and generally tidy
up a fair bit here and there.
Assorted related fixes and adjustments in userland utilities.
WORKAROUNDS:
Do allow r/w opens of r/o media but refuse actual write
operations. This is necessary until the p4::phk_bufwork
branch gets integrated (This problem relates to remounting
not reopening devices, see sys/*/*/${fs}_vfsops.c for details).
Keep PC98's private copy of the old floppy driver compiling
and presumably working (see below).
TODO (planned)
Move probing of drives until after interrupts/timeouts work
(like for ATA/SCSI drives).
TODO (unplanned)
This driver should be made to work on PC98 as well.
Test on YE-DATA PCMCIA floppy drive.
Fix 2.88M media.
This is a MT5 candidate (depends on the bioq_takefirst() addition).
* Some systems have _FDE and child floppy devices, but no _FDI. This seems
to be compatible with the standard. Don't error out if there is no _FDI.
Instead, continue on to the next device. The normal fd probe will take
care of this device.
* Some systems have _FDE but no child devices in AML. For these, add a
second pass that compares the results of _FDE to the presence of devices.
If not present, add the missing device.
* Some BIOS authors didn't read the spec. They use tape drive values for
all fdc(4) devices. Since this isn't grossly incompatible with the
required boolean value, use them. They also define the _FDE items as a
package instead of buffer. Regenerate the buffer from the package if it
is present.
Tested by: tjr, marcel
