d_mmap methods. prep_cdevsw() already installs the shims that
acquire/drop Giant for the methods of a driver that specified the
D_NEEDGIANT flag.
Reviewed by: alc
Approved by: re (kensmith)
- If the path cost is calculated when the link is down, set a pending flag so
it is calculated again when it comes back up.
- To not use 00:00:00:00:00:00 as the bridge id, all interfaces are scanned and
the lowest number wins. All zeros is too low.
Approved by: re (rwatson)
ia64_cpu.h. This improves readability and consistency and aids in
auditing the code.
Add instruction-serialization after writing to cr.pta.
Delay enabling interrupts until after we setup the clocks and after
we program the task priority register.
Approved by: re (blanket)
ia64_cpu.h. This improves readability and consistency and aids in
auditing the code.
Add data-serialization after writing to the region registers and
add instruction-serialization after writing to cr.pta.
Approved by: re (blanket)
ia64_cpu.h. This improves readability and consistency and aids in
auditing the code.
Add data-serialization after writing to cr.tpr.
Approved by: re (blanket)
tdq_group structure. Hyper-threaded cores won't really benefit from
seperate locks anyway.
- Seperate out the migration case from sched_switch to simplify the main
switch code. We only migrate here if called via sched_bind().
- When preempted place the preempted thread back in the same queue at
the head.
- Improve the cpu group and topology infrastructure.
Tested by: many on current@
Approved by: re
message explained why the size is 1 sector, but the code used a
size of 1 cluster.
I/o sizes larger than necessary may cause serious coherency problems
in the buffer cache. Here I think there were only minor efficiency
problems, since a too-large fsinfo buffer could only get far enough
to overlap buffers for the same vnode (the device vnode), so mappings
are coherent at the page level although not at the buffer level, and
the former is probably enough due to our limited use of the fsinfo
buffer.
Approved by: re (kensmith)
- Copy before testing a pointer. This closes a race window.
- Use msleep with the node interlock instead of tsleep.
- Do proper locking around access to tn_vpstate.
- Assert vnode VOP lock for dir_{atta,de}tach to capture
inconsistent locking.
Suggested by: kib
Submitted by: delphij
Reviewed by: Howard Su
Approved by: re (tmpfs blanket)
cpu_start_mp(). This is after we have read the cpuid registers to
calculate the hyperthreading_cpus value for the sysctl that enables or
disables hyperthread cores. Change mp_topology() to use that information
rather than trying to do it itself.
This solves the problem of ULE being incorrectly told that dual core
Athlon64 X2 or Operton cpus are hyperthreading cores. At the very least,
we now have a single piece of code to identify hyperthreading.
Obtained from: jhb
Approved by: re (kensmith)
that the listen-on stuff floats up to the first "page" of text. This
makes it very obvious what's going on so that someone trying to enable
a server for use on a network can easily see how to do that.
2. Change the default behavior back to using a hint zone for the root.
3. Leave the root slave zone config as a commented out example.
4. Remove the B and F root servers from the example at the request of
their operators.
Requested by: he-who-must-not-be-named [1]
Requested by: many [2]
Approved by: re (rwatson)
Merge in parts of the old fast_ipsec.4 man page to ipsec.4 and
start updating ipsec.4 man page.
Reviewed by: brueffer, sam (slightly earlier versions), bmah
Approved by: re (bmah)
64bit counters are needed to simplify traffic accounting and
reduce system load at the big PPP concentrators.
Approved by: re (rwatson), glebius (mentor)
Till now node's transmit path was completely unprotected
and so wasn't thread safe in multilink mode. It's receive path was
declared as WRITER as the simpliest protection method but it
reduces performance when compression or encryption enabled.
Approved by: re (rwatson), glebius (mentor)
communicate with another private port.
All unicast/broadcast/multicast layer2 traffic is blocked so it works much the
same way as using firewall rules but scales better and is generally easier as
firewall packages usually do not allow ARP blocking.
An example usage would be having a number of customers on separate vlans
bridged with a server network. All the vlans are marked private, they can all
communicate with the server network unhindered, but can not exchange any
traffic whatsoever with each other.
Approved by: re (rwatson)
be in ticks "for algorithm stability" when originally committed, it turns
out that it has a significant impact in timing out connections. When we
changed HZ from 100 to 1000, this had a big effect on reducing the time
before dropping connections.
To demonstrate, boot with kern.hz=100. ssh to a box on local ethernet
and establish a reliable round-trip-time (ie: type a few commands).
Then unplug the ethernet and press a key. Time how long it takes to
drop the connection.
The old behavior (with hz=100) caused the connection to typically drop
between 90 and 110 seconds of getting no response.
Now boot with kern.hz=1000 (default). The same test causes the ssh session
to drop after just 9-10 seconds. This is a big deal on a wifi connection.
With kern.hz=1000, change sysctl net.inet.tcp.rexmit_min from 3 to 30.
Note how it behaves the same as when HZ was 100. Also, note that when
booting with hz=100, net.inet.tcp.rexmit_min *used* to be 30.
This commit changes TCPTV_MIN to be scaled with hz. rexmit_min should
always be about 30. If you set hz to Really Slow(TM), there is a safety
feature to prevent a value of 0 being used.
This may be revised in the future, but for the time being, it restores the
old, pre-hz=1000 behavior, which is significantly less annoying.
As a workaround, to avoid rebooting or rebuilding a kernel, you can run
"sysctl net.inet.tcp.rexmit_min=30" and add "net.inet.tcp.rexmit_min=30"
to /etc/sysctl.conf. This is safe to run from 6.0 onwards.
Approved by: re (rwatson)
Reviewed by: andre, silby
that could cause panics and corruption under moderate load. Many thanks
to Matt Reimer, Tom McDonald, and the rest of the guys at VPOP.net for
their help in identifying and testing this.
Approved by: re
only USB 1.1 speeds available, but this shouldn't hurt. Now that we have
working usb support for this board, this is a natural followup.
Approved by: re (kensmith)
7 months. You must have JP6 in the 1-2 position to supply power to the
USB devices, but I've used uftdi, uplcom and umass successfully. If you
have it in 2-3, then nothing will show up. Also, if you have the FQPA
packaging for the AT91RM9200 (like the KN9202 boards have), you will get
the following message
uhub0: device problem (IOERROR), disabling port 2
due to a hardware erratum. It is safe to ignore as it is about pins that
aren't brought out on the FQPA package and aren't proeprly terminated either.
Alas, there's no register to read to tell the FQPA from the BGA versions.
Submitted by: Daan Vreeken
Approved by: re (kensmith)
revision 1.66
date: 2007/07/31 06:23:26; author: marcel; state: Exp; lines: +2 -2
Fix backward compatibility of the "old" (i.e. FreeBSD6) lseek
syscall. It was broken when a new lseek syscall was introduced.
The problem is that we need to swap the 32-bit td_retval values
for the __syscall indirect syscall when the actual syscall has
a 32-bit return value. Hence, we need to exclude lseek(2). And
this means the "old" lseek(2) as well -- which we didn't.
Based on a patch from: grehan@
Approved by: re (blanket)
syscall. It was broken when a new lseek syscall was introduced.
The problem is that we need to swap the 32-bit td_retval values
for the __syscall indirect syscall when the actual syscall has
a 32-bit return value. Hence, we need to exclude lseek(2). And
this means the "old" lseek(2) as well -- which we didn't.
Based on a patch from: grehan@
Approved by: re (rwatson)
* Allow libarchive_test to compile on Interix again.
* Track the test name (not just line number) when counting skipped tests.
Thanks to: Joerg Sonnenberger
Approved by: re (blanket; libarchive testing)
errors (especially when jumbo frames are enabled or in low memory systems)
because the RX chain was corrupted when an mbuf was mapped to an unexpected
number of buffers.
- Fixed a problem that would cause kernel panics when an excessively
fragmented TX mbuf couldn't be defragmented and was released by
bce_tx_encap().
Approved by: re(hrs)
MFC after: 7 days
