kernel as a pseudo-device. The changes were:
- #ifdef DEBUG -> #ifdef VINUMDEBUG
- opt_vinum.h for holding above config variable
- Fixing up a few stray problems where DEBUG wasn't optional.
- config.c -> vinumconfig.c (there's already a config.o)
- Other *.c -> vinum*.c (wasn't strictly necessary, but done in case we end
up with something else conflicting later on and we might have to have yet
more repository copies of files).
- include file paths fixups.. (ie: get them all from the kernel tree
instead of partly from the kernel and partly from /usr/include/machine)
I've spoken with Greg about this.. I hope this doesn't mess him around
too much..
in cyopen() were done in a different order than in sioopen(), partly
to (ab)use a side effect of comparam() and partly because I didn't
understand what the reset was doing (it flushes the fifos). This
turned out to be more than a cosmetic problem. Flushing the fifos
quite late is good for discarding input that arrived while the line
state was being initialized, and in the cy driver it also seems to
reduce a problem with input that arrived long ago during the previous
close (the UART loses sync too easily and for too long).
The optimisation of only waiting before issuing new commands is
obviously invalid in general and it caused many errors in NIST-PCTS.
I think the errors were mostly for characters sent with the wrong
parity, etc., after a half complete tcsetattr().
Use microtime() instead of a magic loop count to limit the wait.
The wait is a busy-wait :-( and normally takes about 500 usec.
almost works properly. Unfortunately, there is no way to flush
the rx fifo without resetting the channel, which also flushes the
tx fifo. We avoid resetting even when both fifos need to be flushed,
since resetting seems to cause the rx to lose sync if it is done
while data is arriving.
Reminded by: NIST-PCTS
hardware is interrupt-driven to a fault and sending a BREAK requires
mode switching. Always running in the BREAK-capable mode as in PR 8318
would double the overhead for sending \0's.
Reminded by: PR 8318
Use the host message loop for any unknown message types instead of performing
a reject message in the sequencer. Pass reject messages to the host
message loop too which frees up a sequencer interrupt type slot.
Default to issuing a bus reset if initiator mode is enabled. It seems
that the reset scsi bus bit is not defined in the same location for
all aic78xx BIOSes, so attempting to honor this setting will have to
wait until I get more information on how to detect it.
Nuke some unused variables.
Not tested on the if_sr, if_cx and if_ar drivers, but
expected to work just the same as it used to.
Any users of these drivers (or even better: donors
of hardware for them) please contact phk@freebsd.org
so we can test the next batch of changes to if_sppp.
as well as several functional additions.
(1) dot3 MIB support.
(2) if_media selection method support.
(3) bridge support.
(4) new boards support. Supported boards are as follows.
[PC/AT]
* Fujitsu FMV-180 series
* Allied-Telesis RE2000 series
* Allied-Telesyn AT1700 series
* Gateway Communications G/Ether series
* UB networks Access/PC ISA series
* TDK/LANX LAC-AX series
* ICL EtherTeam16i series
* RATOC REX-5586/5587
[PC-98]
* Allied-Telesis RE1000 series
* Allied-Telesis RE1000Plus/ME1500 series
* Contec C-NET(9N)E series
* Contec C-NET(98)P2 series
* UB networks Access/PC N98C+ series
* TDK/LANX LAC-98 series(not tested)
Submitted by: seki@sysrap.cs.fujitsu.co.jp (Masahiro Sekiguchi) and
chi@bd.mbn.or.jp (Chiharu Shibata)
in target mode, but we are not completing the command.
Use a template of allowed bus arbitration phases to selectively and
dynamically enable/disable initiator or target (re)selection.
Properly handle timeouts for target role transactions - just go to the
bus free state and report the error to the peripheral driver.
Checkpoint support for the XPT_ABORT_CCB function code. This currently
handles the accept tio and immediate notify ccb types, but does not
handle the continue target I/O or SCSI I/O ccb types. This is enough
to handle dynamic target enable/disable events.
Clean up the SCSI reset code so that we perform at most 1 SCSI bus
reset at initialization, the reset requested by the XPT layer.
pointed this out, but I've not seen a manifestation of this.
o Check against 0x00 as well as 0xff for geometry register, as some clone
cards don't return 0xff. Vadim Mikhailov pointed this out in PR
8743 for his Dell SCSI Array controller working in AHA-1540
emulation mode. Note that this test is likely to go away in the
future in favor of a better one Justin has recommended.
memory address space rather than IO space.. reflect this when looking for the
interface revision register.
If this is not true for them all then we probably need some smarter code.
const char *. Originally I was going to add casts from const char * to
char * in some of the pci device drivers, but the reality is that the
pci device probes return constant quoted strings.
