Instead of reading Ethernet RFC 2819 pXtoYoctets counters from
hardware which counts RX octets, count tx_stat_pXtoYoctets from
Ethernet extended counters which counts TX octets.
TX jumbo counters should be accumulated only after the PPCNT
counters were fetched from hardware with their latest value.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Avoid an infinite software firmware reset loop that may be caused by a
hardware bug by limiting the maximum number of resets.
The counter between resets is reset by request for reset, and not by a
successful reset.
The interval between two resets can be configured via sysctl:
hw.mlx5.sw_reset_timeout
which is global to all mlx5 devices in the system.
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
Make sure the interrupt handlers don't race with the fast unload one
code in the shutdown handler.
MFC after: 3 days
Sponsored by: Mellanox Technologies
Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Linux commit:
1865ea9adbfaf341c5cd5d8f7d384f19948b2fe9
Submitted by: slavash@
MFC after: 3 days
Sponsored by: Mellanox Technologies
While at it remove unused interface state bits. This also fixes and issue
during shutdown:
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Linux commit:
10a8d00707082955b177164d4b4e758ffcbd4017
b3cb5388499c5e219324bfe7da2e46cbad82bfcf
MFC after: 3 days
Sponsored by: Mellanox Technologies
Add support for DIM based on Linux,
with some minor adaptions specific to FreeBSD.
Linux commit
f97c3dc3c0e8d23a5c4357d182afeef4c67f5c33
MFC after: 3 days
Sponsored by: Mellanox Technologies
This is a prerequisite of unifying kernel zlib instances.
Submitted by: Yoshihiro Ota <ota at j.email.ne.jp>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20191
tun(4) and tap(4) share the same general management interface and have a lot
in common. Bugs exist in tap(4) that have been fixed in tun(4), and
vice-versa. Let's reduce the maintenance requirements by merging them
together and using flags to differentiate between the three interface types
(tun, tap, vmnet).
This fixes a couple of tap(4)/vmnet(4) issues right out of the gate:
- tap devices may no longer be destroyed while they're open [0]
- VIMAGE issues already addressed in tun by kp
[0] emaste had removed an easy-panic-button in r240938 due to devdrn
blocking. A naive glance over this leads me to believe that this isn't quite
complete -- destroy_devl will only block while executing d_* functions, but
doesn't block the device from being destroyed while a process has it open.
The latter is the intent of the condvar in tun, so this is "fixed" (for
certain definitions of the word -- it wasn't really broken in tap, it just
wasn't quite ideal).
ifconfig(8) also grew the ability to map an interface name to a kld, so
that `ifconfig {tun,tap}0` can continue to autoload the correct module, and
`ifconfig vmnet0 create` will now autoload the correct module. This is a
low overhead addition.
(MFC commentary)
This may get MFC'd if many bugs in tun(4)/tap(4) are discovered after this,
and how critical they are. Changes after this are likely easily MFC'd
without taking this merge, but the merge will be easier.
I have no plans to do this MFC as of now.
Reviewed by: bcr (manpages), tuexen (testing, syzkaller/packetdrill)
Input also from: melifaro
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D20044
Checksum offloading for SCTP is not currently specified for virtio.
If the hypervisor announces checksum offloading support, it means TCP
and UDP checksum offload. If an SCTP packet is sent and the host announced
checksum offload support, the hypervisor inserts the IP checksum (16-bit)
at the correct offset, but this is not the right checksum, which is a CRC32c.
This results in all outgoing packets having the wrong checksum and therefore
breaking SCTP based communications.
This patch removes SCTP checksum offloading support from the virtio
network interface.
Thanks to Felix Weinrank for making me aware of the issue.
Reviewed by: bryanv@
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D20147
While Linux strace(1) doesn't strictly require it - it has a fallback
to PTRACE_GETREGS - it's a newer interface, so we better support it
before the old one is deprecated.
Reviewed by: dchagin
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20152
device_printf does multiple calls to printf allowing other console messages to
be inserted between the device name, and the rest of the message. This change
uses sbuf to compose to two into a single buffer, and prints it all at once.
It exposes an sbuf drain function (drain-to-printf) for common use.
Update documentation to match; some unit tests included.
Submitted by: jmg
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D16690
Multiple tools use @generated to identify generated files (for example,
in a review Phabricator will by default hide diffs in generated files).
Use the @generated tag in makesyscalls.sh as we've done for other
generated files.
Reviewed by: cem
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D20183
RISC-V ISA specifies no cache management instructions so leave cache
operations in cpufunc.h as no-op for now.
Note some new hardware comes with their own memory-mapped cache
management controller.
Tested on HiFive Unleashed board with cgem(4).
Reviewed by: markj
Obtained from: arm64
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D20126
Multiple tools use @generated to identify generated files (for example,
in a review Phabricator will by default hide diffs in generated files).
Use the @generated tag in makeobjops.awk and vnode_if.awk as we've done
for other generated files.
Sponsored by: The FreeBSD Foundation
times - on every interrupt by using an own set of device methods for the
IGB class. This translates to introducing igb_if_intr_{disable,enable}()
and igb_if_{rx,tx}_queue_intr_enable() with that IGB-specific code moved
out of their EM counterparts and otherwise continuing to use the EM IFDI
methods also for IGB.
Note that igb_if_intr_{disable,enable}() also issue E1000_WRITE_FLUSH as
lost with the conversion of igb(4) to iflib(4).
Also note, that the em_if_{disable,enable}_intr() methods are renamed to
em_if_intr_{disable,enable}() for consistency with the names used in the
interface declaration.
o In em_intr():
- Don't bother to bail out if the interrupt type is "legacy", i. e. INTx
or MSI, as iflib(4) doesn't use ift_legacy_intr methods for MSI-X. All
other iflib(4)-based drivers avoid this check, too.
- Given that only the MSI-X interrupts have one-shot behavior (by taking
advantage of the EIAC register), explicitly disable interrupts. Hence,
em_intr() now matches what {em,igb}_irq_fast() previously did (in case
of igb(4) supposedly also to work around MSI message reordering errata
on certain systems).
o In em_if_intr_disable():
- Clear the EIAC register unconditionally for 82574 and not just in case
of MSI-X, matching em_if_intr_enable() and bringing back the last hunk
of r206437 lost with the iflib(4) conversion.
- Write to EM_EIAC for clearing said register instead of to the IGB-only
E1000_EIAC used ever since the iflib(4) conversion.
Reviewed by: shurd
Differential Revision: https://reviews.freebsd.org/D20176
MSI. Unlike as with iflib_fast_intr_ctx(), the former will also enqueue
_task_fn_tx() in addition to _task_fn_rx() if appropriate, bringing TCP
TX throughput of EM-class devices on par with the MSI-X case and, thus,
close to wirespeed/pre-iflib(4) times again. [1]
Note that independently of the interrupt type, the UDP performance with
these MACs still is abysmal and nowhere near to where it was before the
conversion of em(4) to iflib(4).
o In iflib_init_locked(), announce which free list failed to set up.
o In _task_fn_tx() when running netmap(4), issue ifdi_intr_enable instead
of the ifdi_tx_queue_intr_enable method in case of a "legacy" interrupt
as the latter is valid with MSI-X only.
o Instead of adding the missing - and apparently convoluted enough that a
DBG_COUNTER_INC was put into a wrong spot in _task_fn_rx() - checks for
ifdi_{r,t}x_queue_intr_enable being available in the MSI-X case also to
iflib_fast_intr_rxtx(), factor these out to iflib_device_register() and
make the checks fail gracefully rather than panic. This avoids invoking
the checks at runtime over and over again in iflib_fast_intr_rxtx() and
_task_fn_{r,t}x() - even if it's just in case of INVARIANTS - and makes
these functions more readable.
o In iflib_rx_structures_setup(), only initialize LRO resources if device
and driver have LRO capability in order to not waste memory. Also, free
the LRO resources again if setting them up fails for one of the queues.
However, don't bother invoking iflib_rx_sds_free() in that case because
iflib_rx_structures_setup() doesn't call iflib_rxsd_alloc() either (and
iflib_{device,pseudo}_register() will issue iflib_rx_sds_free() in case
of failure via iflib_rx_structures_free(), but there definitely is some
asymmetry left to be fixed, though).
o Similarly, free LRO resources again in iflib_rx_structures_free().
o In iflib_irq_set_affinity(), handle get_core_offset() errors gracefully
instead of panicing (but only in case of INVARIANTS). This is a follow-
up to r344132, as such driver bugs shouldn't be fatal.
o Likewise, handle unknown iflib_intr_type_t in iflib_irq_alloc_generic()
gracefully, too.
o Bring yet more sanity to iflib_msix_init():
- If the device doesn't provide enough MSI-X vectors or not all vectors
can be allocate so the expected number of queues in addition to admin
interrupts can't be supported, try MSI next (and then INTx) as proper
MSI-X vector distribution can't be assured in such cases. In essence,
this change brings r254008 forward to iflib(4). Also, this is the fix
alluded to in the commit message of r343934.
- If the MSI-X allocation has failed, don't prematurely announce MSI is
going to be used as the latter in fact may not be available either.
- When falling back to MSI, only release the MSI-X table resource again
if it was allocated in iflib_msix_init(), i. e. isn't supplied by the
driver, in the first place.
o In mp_ndesc_handler(), handle unknown type arguments gracefully, too.
PR: 235031 (likely) [1]
Reviewed by: shurd
Differential Revision: https://reviews.freebsd.org/D20175
resume where the last search left off. Suppose that there are no free
blocks of size 32, but plenty of size 16. If we repeatedly request
size 32 blocks, fail, and retry with size 16 blocks, then the failures
all reset the cursor to the beginning of memory, making the 16 block
allocation use a first fit, rather than next fit, strategy.
This change has blist_alloc make a copy of the cursor for its own
decision making, and only updates the real blist cursor after a
successful allocation, making those 16 block searches behave like
next-fit searches.
Approved by: markj (mentor)
Differential Revision: https://reviews.freebsd.org/D20177
- Remove the only ever written to ift_db_mtx_name member of struct iflib_txq.
- Remove the unused or only ever written to ifr_size, ifr_cq_pidx, ifr_cq_gen
and ifr_lro_enabled members of struct iflib_rxq.
- Consistently spell DMA, RX and TX uppercase in comments, messages etc.
instead of mixing with some lowercase variants.
- Consistently use if_t instead of a mix of if_t and struct ifnet pointers.
- Bring the function comments of _iflib_fl_refill(), iflib_rx_sds_free() and
iflib_fl_setup() in line with reality.
- Judging problem reports, people are wondering what on earth messages like:
"TX(0) desc avail = 1024, pidx = 0"
are trying to indicate. Thus, extend this string to be more like that of
non-iflib(4) Ethernet MAC drivers, notifying about a watchdog timeout due
to which the interface will be reset.
- Take advantage of the M_HAS_VLANTAG macro.
- Use false/true rather than FALSE/TRUE for variables of type bool.
- Use FALLTHROUGH as advocated by style(9).
Only two interfaces are created eth0 and lo and they expose
the following properties:
address, addr_len, flags, ifindex, mty, tx_queue_len and type.
Initial patch developed by Carlos Neira in 2017 and finished by me.
PR: 223722
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13656
a final revision.
Fix style issues and change bool-like variables from int to bool.
Reviewed by: emaste
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D20141
Allow users to specify multiple dump configurations in a prioritized list.
This enables fallback to secondary device(s) if primary dump fails. E.g.,
one might configure a preference for netdump, but fallback to disk dump as a
second choice if netdump is unavailable.
This change does not list-ify netdump configuration, which is tracked
separately from ordinary disk dumps internally; only one netdump
configuration can be made at a time, for now. It also does not implement
IPv6 netdump.
savecore(8) is already capable of scanning and iterating multiple devices
from /etc/fstab or passed on the command line.
This change doesn't update the rc or loader variables 'dumpdev' in any way;
it can still be set to configure a single dump device, and rc.d/savecore
still uses it as a single device. Only dumpon(8) is updated to be able to
configure the more complicated configurations for now.
As part of revving the ABI, unify netdump and disk dump configuration ioctl
/ structure, and leave room for ipv6 netdump as a future possibility.
Backwards-compatibility ioctls are added to smooth ABI transition,
especially for developers who may not keep kernel and userspace perfectly
synced.
Reviewed by: markj, scottl (earlier version)
Relnotes: maybe
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D19996
As Linux comment for this function point:
Signal to the system that the PCI device is not in use by the system
anymore. This only involves disabling PCI bus-mastering, if active.
Build tested drm-current-kmod prior to commit.
MFC after: 1 week
Submitted by: slavash@
Sponsored by: Mellanox Technologies
Equivalent to r339958 for sys/kern/syscalls.master.
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14858
Turning on pr_debug at compile time make it non-optional at runtime.
This often means that the amount of the debugging is unbearable.
Allow developer to turn on pr_debug output only when needed.
Build tested drm-current-kmod prior to commit.
MFC after: 1 week
Submitted by: kib@
Sponsored by: Mellanox Technologies
There's a race between the initialization of devsoftc.mtx (by devinit)
and the creation of the geom worker thread g_run_events, which calls
devctl_queue_data_f. Both of those are initialized at SI_SUB_DRIVERS
and SI_ORDER_FIRST, which means the geom worked thread can be created
before the mutex has been initialized, leading to the panic below:
wpanic: mtx_lock() of spin mutex (null) @ /usr/home/osstest/build.135317.build-amd64-freebsd/freebsd/sys/kern/subr_bus.c:620
cpuid = 3
time = 1
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xfffffe003b968710
vpanic() at vpanic+0x19d/frame 0xfffffe003b968760
panic() at panic+0x43/frame 0xfffffe003b9687c0
__mtx_lock_flags() at __mtx_lock_flags+0x145/frame 0xfffffe003b968810
devctl_queue_data_f() at devctl_queue_data_f+0x6a/frame 0xfffffe003b968840
g_dev_taste() at g_dev_taste+0x463/frame 0xfffffe003b968a00
g_load_class() at g_load_class+0x1bc/frame 0xfffffe003b968a30
g_run_events() at g_run_events+0x197/frame 0xfffffe003b968a70
fork_exit() at fork_exit+0x84/frame 0xfffffe003b968ab0
fork_trampoline() at fork_trampoline+0xe/frame 0xfffffe003b968ab0
--- trap 0, rip = 0, rsp = 0, rbp = 0 ---
KDB: enter: panic
[ thread pid 13 tid 100029 ]
Stopped at kdb_enter+0x3b: movq $0,kdb_why
Fix this by initializing geom at SI_ORDER_SECOND instead of
SI_ORDER_FIRST.
Sponsored by: Citrix Systems R&D
Reviewed by: kevans, markj
Differential revision: https://reviews.freebsd.org/D20148
The more appropriate place to do the flushing is VOP_OPEN(). This was
uncovered because VOP_SET_TEXT() is now called with the vnode'
vm_object rlocked, which is incompatible with the flush operations.
After the move, there is no need for NFS-specific VOP_SET_TEXT
overload.
Sponsored by: The FreeBSD Foundation
MFC after: 30 days
Since the DMAP is only available on powerpc64, and is *always* available on
Book-E powerpc64, don't penalize either side (32-bit or 64-bit) by always
checking hw_direct_map to perform operations. This saves 5-10% time on
various ports builds, and on buildworld+buildkernel on Book-E hardware.
MFC after: 3 weeks
Use the nitems() macro instead of the expansion, a'la r298352. Also, fix the
location of this check to after initializing availmem_regions_sz, so that the
check isn't always against 0, thus always failing (nitems(phys_avail) is always
more than 0).
