Allow i2c bus speed to be configured via hints, FDT data, and sysctl.
Implement bus speed setting for OMAP4, AM335x, and imx5/6.
Fix the i2c bus speed divisors for TI OMAP4 and AM335x to give the
advertised 100, 400, and 1000 KHz speeds.
PR: 195009
Ignore IIC_ENOADDR from iicbus_reset() as it only means we have a
master-only controller.
This fixes the iic bus scan with i2c(8) (on supported controllers).
Tested with gpioiic(4).
MFC r267009:
Remove the unnecessary i2c slave address assignment.
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
r261844, r261845, r261846, r262194, r262522, r262559
r258046:
Fix a typo on a comment in ofw_bus_if.m, the default method will return -1
when a node doesn't exist.
r258047:
Move the KASSERT() check to the point before the increase of number of pins.
r258050:
Fix gpiobus to return BUS_PROBE_GENERIC insted of BUS_PROBE_SPECIFIC (0) so
it can be overriden by its OFW/FDT version.
Give a chance for GPIO devices that implement the device_identify method to
attach.
r259035:
Remove unnecessary includes and an unused softc variable. While here apply
two minor style(9) fixes.
r259036:
Move the GPIOBUS_SET_PINFLAGS(..., ..., pin, GPIO_PIN_OUTPUT) to led(4)
control callback function. This makes gpioled(4) works even if the pin
is accidentally set to an input.
r259037:
Fix the pin value reading on AM335x. Because of the inverted logic it was
always returning '0' for all the reads, even for the outputs. It is now
known to work with gpioiic(4) and gpioled(4).
r261842:
Add an OFW GPIO compatible bus. This allows the use of the DTS files to
describe GPIO bindings in the system.
Move the GPIOBUS lock macros to gpiobusvar.h as they are now shared between
the OFW and the non OFW versions of GPIO bus.
Export gpiobus_print_pins() so it can also be used on the OFW GPIO bus.
r261843:
Add OFW support to the in tree gpio compatible devices: gpioiic(4) and
gpioled(4).
Tested on RPi and BBB (using the hardware I2C controller and gpioiic(4) for
the I2C tests). It was also verified for regressions on RSPRO (MIPS/ar71xx)
used as reference for a non OFW-based system.
Update the gpioled(4) and gpioiic(4) man pages with some details and
examples about the FDT/OFW support.
Some compatibility details pointed out by imp@ will follow in subsequent
commits.
r261844:
Allow the use of OFW I2C bus together with iicbb(4) on OFW-based systems.
This change makes ofw_iicbus attach to iicbb(4) controllers in addition to
the already supported i2c host bridges (iichb).
On iicbb(4) allow the direct access of the OFW parent node by its children,
so they can be directly attached to iicbb(4) node on the DTS without the
need of describing the i2c bus.
r261845:
Allow the use of the OFW GPIO bus for ti_gpio and bcm2835_gpio. With this
change the gpio children can be described as directly connected to the GPIO
controller without the need of describing the OFW GPIO bus itself on the
DTS file.
With this commit the OFW GPIO bus is fully functional on BBB and RPi.
GPIO controllers which want to use the OFW GPIO bus will need similar
changes.
r261846:
Make the gpioled(4) work out of the box on BBB.
Add gpioled(4) to BEAGLEBONE kernel and add the description of the four
on-board leds of beaglebone-black to its DTS file.
r262194:
Remove an unnecessary header.
r262522:
Fix make depend for iicbus.
r262559:
Inspired by r262522, fix make depend. This fixes the build of gpio modules.
extremely outdated, and I doubt that it was ever used for ifnet drivers.
It was used for AF_INET sockets in pre-FreeBSD time.
Approved by: re (hrs)
Sponsored by: Nginx, Inc.
doesn't automatically clear when VDD rises above Vlow again and needs to be
cleared manually. However, apparently this needs all of the time registers
to be set, i.e. pcf8563_settime(), and not just PCF8563_R_SECOND in order
for PCF8563_R_SECOND_VL to stick. Thus, we just issue a warning during
pcf8563_attach() rather than failing with ENXIO in case it is set.
MFC after: 3 days
Add a Simple polled driver iicoc for the OpenCores I2C controller. This
is used in Netlogic XLP processors.
Submitted by: Sreekanth M. S. (kanthms at netlogicmicro com)
The earlier version of the driver is sys/mips/rmi/dev/iic/ds1374u.c
Convert all references to ds1374u to ds1374, and use DEVMETHOD_END.
Also update the license header as Netlogic is now Broadcom.
clients.
These are helful when making certain drivers work on both Linux
and FreeBSD without changing the code flow too much.
Reviewed by: kib, wlosh
MFC after: 1 month
* Right now the delay is hard coded at 10uS. This is a bit long when doing lots
of periodic i2c transactions. So create a 'udelay' parameter and initialise it
to 10. This can be tuned later.
* Add a newline after a transaction finishes, so the debugging output isn't so
horrible.
These realtek switch PHYs speak a variant of i2c with some slightly
modified handling.
From the submitter, slightly modified now that some further digging
has been done:
The I2C framework makes a assumption that the read/not-write bit of the first
byte (the address) indicates whether reads or writes are to follow.
The RTL8366 family uses the bus: after sending the address+read/not-write byte,
two register address bytes are sent, then the 16-bit register value is sent
or received. While the register write access can be performed as a 4-byte
write, the read access requires the read bit to be set, but the first two bytes
for the register address then need to be transmitted.
This patch maintains the i2c protocol behaviour but allows it to be relaxed
(for these kinds of switch PHYs, and whatever else Realtek may do with this
almost-but-not-quite i2c bus) - by setting the "strict" hint to 0.
The "strict" hint defaults to 1.
Submitted by: Stefan Bethke <stb@lassitu.de>
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
- Add retry loops in the i2c read/write functions.
- Combied the ADC channel selection and readout of the value into
one iicbus_transfer to avoid possible races.
Reviewed by: nwhitehorn
- Add a retry loop for the i2c sensor reading.
- Check on busy status of the chip and on invalid values.
- Fix a typo in a comment.
- Replace the constant 2732 with the ZERO_C_TO_K macro.
Approved by: nwhitehorn (mentor)
- Add a retry loop for the i2c sensor reading.
- Update the sensor handling for sensors which do not have a location
entry. [1]
Submitted by: [1] Justin Hibbits.
Approved by: nwhitehorn (mentor)
for this sensor. Instead of leaving this location empty we use here
the default name 'sensor'.
Submitted by: Justin Hibbits <chmeeedalf at gmail dot com>
Approved by: nwhitehorn (mentor)
functionality is the same, a difference is that the DS1775 has a better
precision than the LM75. But we do not use it in our setup. Make the
LM75 work the same as the DS1775.
Fix a typo in device_set_desc.
Tested by: Paul Mather <paul at gromit dlib vt edu>
Approved by: nwhitehorn (mentor)
PowerMac7,2.
- The fcu driver lets us read and write the fan RPMs for all fans in the
PowerMac7,2. This driver is PowerMac specific.
- The ds1775 is a driver to read the temperature for the drive bay sensor.
- The max6690 is another driver to read temperatures. Here it is used to
read the inlet, the backside and the U3 heatsink temperature.
An additional driver, the ad7417, will follow later.
Thanks to nwhitehorn for guiding me through this driver development.
Approved by: nwhitehorn (mentor)
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
