mask of CPUs, pc_other_cpus and pc_cpumask become highly inefficient.
Remove them and replace their usage with custom pc_cpuid magic (as,
atm, pc_cpumask can be easilly represented by (1 << pc_cpuid) and
pc_other_cpus by (all_cpus & ~(1 << pc_cpuid))).
This change is not targeted for MFC because of struct pcpu members
removal and dependency by cpumask_t retirement.
MD review by: marcel, marius, alc
Tested by: pluknet
MD testing by: marcel, marius, gonzo, andreast
setting (either default or if supported as set by SIOCSIFFIB, e.g.
from ifconfig).
Submitted by: Alexander V. Chernikov (melifaro ipfw.ru)
Reviewed by: julian
MFC after: 2 weeks
em drivers.
- Make the per-instance 'enable_aim' sysctl truly per-instance by having it
change a per-instance variable (which is used to control AIM) rather
than having all of the per-instance sysctls operate on a single global
variable.
Reviewed by: jfv (earlier version)
MFC after: 1 week
the AP doesn't transmit beacons.
If the AP requests a CSA (ie, a channel switch) and then enters CAC
(channel availability check) for 60 seconds, it doesn't send beacons
and it just listens for radar events (and other things which we don't
do yet.)
Now, ath_newstate() was not resetting the beacon timer config on
a transition to the RUN state when in STA mode - it was setting
sc_syncbeacon, which simply updates the beacon config from the
contents of the next received beacon.
This means the STA never generates beacon miss events.
If the AP goes into CAC for 60 seconds and recovers, the STA will
happily receive the first beacon and reconfigure timers.
But if it gets a radar event after that, it'll change channel
again, not notify the station that it's changed channel..
and since the station is happily waiting for the first beacon
to configure the beacon timer details from, it won't ever
generate a beacon miss interrupt and it'll sit there forever
(or until the AP appears on that channel once again.)
This change forces the last known beacon timer config to be
written to hardware on a transition from CSA->RUN in STA mode.
This forces bmiss events to occur and the STA will eventually
(after a handful of beacon miss events) begin scanning for
another access point.
get it out of a stuck condition that can be caused by GEM_MAC_RX_OVERFLOW.
- In gem_reset_rxdma() call gem_setladrf() in order to reprogram the RX
filter and restore the previous content of GEM_MAC_RX_CONFIG. While at it
consistently use the newly introduced sc_mac_rxcfg throughout the driver
instead of reading the its old content.
- Increment if_iqdrops instead of if_ierrors in case of RX buffer allocation
failure.
- According to the GEM datasheet the RX MAC should also be disabled in
gem_setladrf() before changing its configuration.
- Add error messages to gem_disable_{r,t}x() and take advantage of these
throughout the driver instead of duplicating their functionality all over
the place.
In joint forces with: yongari
the microcode caused SCB timeouts. Linux driver does not allow
microcode loading for these controllers and jfv also confirmed that
there is no need to do and it shouldn't.
PR: kern/103332
Additional confirmation from: jfv
MFC after: 1 week
The DFS code was tickling the channel set directly whilst going
through the state RUN -> CSA -> RUN. This only changed the channel;
it didn't go via ath_reset(). However in this driver, a channel
change always causes a chip reset, which resets the beacon timer
configuration and interrupt setup. This meant that data would go
out but as the beacon timers never fired, beacons would never
be queued.
The confusing part is that sometimes the state transition was
RUN -> SCAN -> CAC -> RUN (with CSA being in there sometimes);
going via SCAN would clear sc_beacons and thus the transition
to RUN would reprogram beacon transmission.
In case someone tries debugging why suspending a device currently
beaconing (versus just RX'ing beacons which is what occurs in STA
mode), add a silly comment which should hopefully land them at
this commit message. The call to ath_hal_reset() will be clearing
the beacon config and it may not be always reset.
can be tested.
This doesn't at all actually do radar detection! It's just
so developers who wish to test the net80211 DFS code can easily
do so. Without this flag, the DFS channels are never marked
DFS and thus the DFS stuff doesn't run.
latter.
It appears that the addition to uath(4) came in through PR kern/135009,
which had tested another device, the SMCWUSBTG2, successfully with uath(4)
and included the SMCWUSBG as it "has the same chipset". I can find no
other evidence that these two do actually share the same chipset. Moreover,
Linux treats the SMCWUSBG as a zyd(4) device also.
This reverts r223537.
Discussed with: hselasky, kevlo
MFC after: 1 week
LED controller used to run the load graph on the server's front panel.
Reported by: Paul Mather <paul at gromit dot dlib dot vt dot edu>
MFC after: 3 days
dynamically loaded device drivers get a chance to run their event hooks.
- Decouple the USB suspend and resume lock from witness. It produces some
false warnings due to reusing the lock name among multiple devices.
MFC after: 3 days
is now required by bus_autoconf.
- Allow interface class matching even if device class is vendor specific.
- Update bus_autoconf tool to not generate system and subsystem match lines
for the nomatch event.
PR: misc/157903
MFC after: 14 days
sorted according to the mode which they support:
host, device or dual mode
- Add generic tool to extract these data:
tools/bus_autoconf
Discussed with: imp
Suggested by: Robert Millan <rmh@debian.org>
PR: misc/157903
MFC after: 14 days
to do about the few cases where the HAL state isn't available (regdomain)
or isn't yet setup (probe/attach.)
The global ath_hal_debug now affects all instances of the HAL.
This also restores the ability for probe/attach debugging to work; as
the sysctl tree may not be attached at that point. Users can just set
the global "hw.ath.hal.debug" to a suitable value to enable probe/attach
related debugging.
rather than global variables.
This specifically allows for debugging to be enabled per-NIC, rather
than globally.
Since the ath driver doesn't know about AH_DEBUG, and to keep the ABI
consistent regardless of whether AH_DEBUG is enabled or not, enable the
debug parameter always but only conditionally compile in the debug
methods if needed.
The ALQ support is currently still global pending some brainstorming.
Submitted by: ssgriffonuser@gmail.com
Reviewed by: adrian, bschmidt
processors unless the invariant TSC bit of CPUID is set. Intel processors
may stop incrementing TSC when DPSLP# pin is asserted, according to Intel
processor manuals, i. e., TSC timecounter is useless if the processor can
enter deep sleep state (C3/C4). This problem was accidentally uncovered by
r222869, which increased timecounter quality of P-state invariant TSC, e.g.,
for Core2 Duo T5870 (Family 6, Model f) and Atom N270 (Family 6, Model 1c).
Reported by: Fabian Keil (freebsd-listen at fabiankeil dot de)
Ian FREISLICH (ianf at clue dot co dot za)
Tested by: Fabian Keil (freebsd-listen at fabiankeil dot de)
- Core2 Duo T5870 (C3 state available/enabled)
jkim - Xeon X5150 (C3 state unavailable)
resource allocation from an x86 Host-PCI bridge driver so that it can be
reused by the ACPI Host-PCI bridge driver (and eventually the MPTable
Host-PCI bridge driver) instead of duplicating the same logic. Note that
this means that hw.acpi.host_mem_start is now replaced with the
hw.pci.host_mem_start tunable that was already used in the non-ACPI case.
This also removes hw.acpi.host_mem_start on ia64 where it was not
applicable (the implementation was very x86-specific).
While here, adjust the logic to apply the new start address on any
"wildcard" allocation even if that allocation comes from a subset of
the allowable address range.
Reviewed by: imp (1)
