is really EtherExpress or EEPro or what, but it does appear in a
couple of ethernet cards that have appeared recently on ebay. Silicom
appears to make these cards, and they have the 82595TX chipset in
them, and sometimes uarts. The ex driver needs some work to support
these cards, but I thought I'd get the device into pccarddevs.
The hardware driver decides the name under /dev/led and provides
the function to turn the lamp on/off.
All leds are serviced by a single timeout which runs at a basic rate
of hz/10.
The LED is controlled by ascii strings as follows.
0 Turn off.
1 Turn on.
f Flash: _-
f2 Flash: __--
f3 Flash: ___---
f4...f9 etc.
d%d Digits. "d12": -__________-_-______________________________
s%s String, roll your own:
'a-j' gives on for (1...10)/10 sec.
'A-J' gives on for (1...10)/10 sec.
'sAaAbBa': _-_--__-
m%s Morse
'.' dot
'-' dash
' ' letter space
'\n' word space
My mdoc skills do not reach to express that.
Add a sysctl declaration for hw.ata.atapi_dma, which had gone MIA (though
setting it in loader.conf still worked, it was not visible at runtime)
Approved by: sos
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
message encoding and decoding stuff into the base module. All of this
is accessed by several of the NgATM modules and putting this into
atmbase reduceds the memory footprint.
cr.isr sanity check. We actually encounter insanities, which very
likely means that the insanity check itself is insane. Remove an empty
comment while I'm at it.
directly on the radix tree and does not hold any routing table refernces.
This fixes the reference counting problems that manifested itself as a
panic during unmount of filesystems that were mounted by NFS over an
interface that had been removed.
Supported by: FreeBSD Foundation
idle. They figure out that we're idle fast enough that the cache pollution
introduces by scanning their run queue is more expensive than waiting
a little longer.
- Add kseq_setidle() to mark us as being idle. Use this in place of
kseq_find().
- Remove kseq_load_highest(), kseq_find() was the only consumer of this
interface. kseq_balance() has it's own customized version that finds the
lowest and highest loads simultaneously.
Continuously told that this would be faster by: terry
GEOM was not designed to handle media that does not have
a size. Blank CD's are of that type, so cheat and set the
media size to -1. This allows burning to work, but makes
GEOM issue outofrange reads that makes the ATAPI subsystem
spew out a few warnings. GEOM should be tought about this.
GEOM was not designed to handle changing the sectorsize
between opens. Writing multitack CD's with both audio and
data tracks needs to change sector size on the fly. We
cheat here and stuff the current sectorsize into GEOM
private internals. GEOM should grow some clean way for this.
o Fix MFC cards. We were bogusly setting CCR_IOBASE[01] and CCR_IOLIMIT.
now when we activate the resource, we adjust these for MFC cards, per the
spec.
o Change type of pf_mfc_* to be bus_addr_t, which is more correct than
long.
This makes my 3C362D/3C363D and 3CXEM556 cards work! Woo Hoo!
o Remove redundant $FreeBSD$
o Better comments about ep_get_macaddr.
o remove one tab in a switch statement (style only)
o Recognize ID 0x0035 as the device ID for the 3CXEM556 that I have. This
makes the 3CXEM556 work for me. Not 100% sure this is the assigned ID,
as I don't have the datasheets for this part, but it does work and get
the correct ethrnet address.
o Comment about the whole fake IRQ 3 thing. some need it, some don't, all
work with it.
the total load, the timeshare load, and the number of threads that can
be migrated to another cpu. Account for these seperately.
- Introduce a KSE_CAN_MIGRATE() macro which determines whether or not a KSE
can be migrated to another CPU. Currently, this only checks to see if
we're an interrupt handler. Eventually this will also be used to support
CPU binding.
An example of useless is bios.h. An example of wrong is msdos.h (due
to the use of long for 32-bit fields).
display.h cannot be removed because it's used by syscons. That header
however has no platform dependency and shouldn't really be here.
Removal if these headers may cause build failures in the ports tree.
It's the ports that need fixing in that case.
Tested with: buildworld, LINT
previously only considered the send sequence space. Unfortunately,
some OSes (windows) still use a random positive increments scheme for
their syn-ack ISNs, so I must consider receive sequence space as well.
The value of 250000 bytes / second for Microsoft's ISN rate of increase
was determined by testing with an XP machine.
