The MMCHS hardware is pretty much a standard SDHCI v2.0 controller with a
couple quirks, which are now supported by sdhci(4) as of r254507.
This should work for all TI SoCs that use the MMCHS hardware, but it has
only been tested on AM335x right now, so this enables it on those platforms
but leaves the existing ti_mmchs driver in place for other OMAP variants
until they can be tested.
This initial incarnation lacks DMA support (coming soon). Even without it
this improves performance pretty noticibly over the ti_mmchs driver,
primarily because it now does multiblock IO.
Add support for A20 timer.
Correct interrupt offset depending from chip.
Add basic code for CPU configuration module.
For now, add kernel config and dts file
(only FDT blob related problem needs to be solved later in
order to have one kernel for both cubieboard1 and 2).
Approved by: ray@
the beaglebone-specific .dts file.
Add a new .dts for the BeagleBone Black with more memory,
slightly different pinmux initialization, and with mmchs1
configured (though the latter doesn't quite work yet).
to driver specific files.
- window initialization is done during device attach
- CESA TDMA decoding windows values are set based on DTS,
not copied from CPU registers
- remove unnecessary virtual mapping
- update dts file
Obtained from: Semihalf
they can easily be used by later post-processing. When searching for
a compiled-in fdt blob, use the section headers to get the size and
location of the .dynsym section to do a symbol search.
This fixes a problem where the search could overshoot the symbol
table and wander into the string table. Sometimes that was harmless
and sometimes it lead to spurious panic messages about an offset
bigger than the module size.
After digging through more carefully, it looks like there's
no real need to have the DTB in the module directory.
So we can simplify a lot: Just copy DTB into local heap
for "fdt addr" and U-Boot integration, drop all the extra
COPYIN() calls.
I've left one final COPYIN() to update the in-kernel DTB
for consistency with how this code used to work, but I'm
no longer convinced it's appropriate here.
I've also remove the mem_load_raw() utility that I added
to boot/common/module.c with r247045 since it's no longer
necessary.
initialized after FPIO controller since they might rely on GPIO
functionality
- Update interrupts property of dma node to contain all allocated
interrupts
This was broken by r247045 which tried to copy the FDT into the
module directory immediately.
Instead, store the address and arrange for the FDT to get
copied into the module directory later when the usual
FDT initialization runs.
When initializing the fdt, query U-Boot as well.
With this change, it is now feasible to have U-Boot load
the FDT, ubldr will pull it from U-Boot and hand it to the
kernel.
This adds support for version 10, revision 01, but it should also work
without changes for the 0901 model, at least until we get drivers for the
two different wifi chips involved.
Many users contributed to and tested the various patchsets floating around
for the past year that have eventually evolved into this checkin, most notably
Richard Neese who provided the bulk of the kernel config file.
Approved by: cognet (mentor)
- Add "fdt addr" subcommand that lets you specify preloaded blob address
- Do not pre-initialize blob for "fdt addr"
- Do not try to load dtb every time fdt subcommand is issued,
do it only once
- Change the way DTB is passed to kernel. With introduction of "fdt addr"
actual blob address can be not virtual but physical or reside in
area higher then 64Mb. ubldr should create copy of it in kernel area
and pass pointer to this newly allocated buffer which is guaranteed to work
in kernel after switching on MMU.
- Convert memreserv FDT info to "memreserv" property of root node
FDT uses /memreserve/ data to notify OS about reserved memory areas.
Technically it's not real property, it's just data blob, sequence
of <start, size> pairs where both start and size are 64-bit integers.
It doesn't fit nicely with OF API we use in kernel, so in order to unify
thing ubldr converts this data to "memreserve" property using the same
format for addresses and sizes as /memory node.
Rasperry Pi firmware has a set of hardcoded pathes it uses to fill
FDT with system-specific information like display resolution, memory
size, UART and SDHCI clocks, ethernet MAC address. Handle two of them:
- Add placeholder for ethernet MAC address
- Move display node out of "axi" node
MSI are implemented via software interrupt. PCIe cards will write
into software interrupt register which will cause inbound shared
interrupt which will be interpreted as a MSI.
Obtained from: Marvell, Semihalf
- Add functions to calculate clocks instead using hardcoded values
- Update reset and timers functions
- Update number of interrupts
- Change name of platform from db88f78100 to db78460
- Correct DRAM size and PCI IRQ routing in dts file.
Obtained from: Semihalf
r239274 added support for ranges. Update XLP DTS to provide the correct
range parameter for the XLP SoC bus. Also fix bus_space_map method
for XLP bus space.
Submitted by: Sreekanth M. <sreekanth.molagavalli@broadcom.com>
