zpool the output causes the script to bail out with syntax errors.
Since a scrub of a faulted zpool is pointless, just skip over any pools
marked as such.
PR: conf/150228
Submitted by: jpaetzel
Approved by: kib (mentor)
MFC after: 3 days
MFC note: only for RELENG_8
While I'm here, don't run the sysctl frob unconditionally, and
s/sysctl/$SYSCTL/
PR: conf/153460 [1]
Submitted by: Grigory Rechistov <ggg_mail@inbox.ru>
and configure minimal target addresses & notifications needed for bsnmpd(1)
to send SNMPv3 notifications.
Sponsored by: The FreeBSD Foundation
Reviewed by: philip
Approved by: philip
snmp_vacm modules and minimal user/view configurations needed to for
the modules to work properly.
Sponsored by: The FreeBSD Foundation
Reviewed by: philip@ (mostly)
Approved by: philip@
case user wants to implement his own actions and doesn't want the attributes to
vanish.
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 3 days
and add protocol entries for protocols which have SCTP port allocations.
These entries are according to
http://www.iana.org/assignments/port-numbers
as of today. Also add SCTP port allocation entires for the
echo, daytime, and chargen service.
Discussed with rwatson@
MFC after: 3 days.
group on a object has less permissions that everyone). These
permissions will not work reliably over NFS if you have more than
14 supplemental groups and are usually not what you mean.
MFC after: 1 week
Hardware donated by: Rusty Nejdl rnejdl at ringofsaturn dot com
Tested by: Rusty Nejdl rnejdl at ringofsaturn dot com
Tested by: Andrzej Tobola ato at iem dot pw dot edu dot pl
MFC after: 3 weeks
set to use DHCP have no carrier. This can cause grief as it may take
some time for link to be established, and defaultroute may terminate
before this happens.
Introduce a defaultroute_carrier_delay variable and then wait that long
in defaultroute before bailing if no interfaces have carrier. With the
default settings defaultroute will wait for five seconds for this, and
the original 30 second wait for a default route to appear is unchanged.
Note that there is in discussion an alternative approach to the broader
problem of waiting for DHCP-configured routes. However, this change
addresses a real problem in the current defaultroute script.
Discussed on: freebsd-rc@
- looking for partition with 'bootonce' attribute alone (without 'bootme'
attribute), removing it and logging that we successfully booted from this
partition.
- looking for partitions with 'bootfailed' attribute, removing it and
logging that we failed to boot from this partition.
Reviewed by: arch (Message-ID: <20100917234542.GE1902@garage.freebsd.pl>)
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 2 weeks
The $ip6addrctl_policy is a variable to choose a pre-defined address
selection policy set by ip6addrctl(8).
The keyword "ipv4_prefer" sets IPv4-preferred one described in Section 10.3,
the keyword "ipv6_prefer" sets IPv6-preferred one in Section 2.1 in RFC 3484,
respectively. When "AUTO" is specified, it attempts to read
/etc/ip6addrctl.conf first. If it is found, it reads and installs it as
a policy table. If not, either of the two pre-defined policy tables is
chosen automatically according to $ipv6_activate_all_interfaces.
When $ipv6_activate_all_interfaces=NO, interfaces which have no corresponding
$ifconfig_IF_ipv6 is marked as IFDISABLED for security reason.
The default values are ip6addrctl_policy=AUTO and
ipv6_activate_all_interfaces=NO.
Discussed with: ume and bz
unless it is the current timer. When we have resumed successfully, restore
the previous timecounter hardware if it was changed earlier. Only the ACPI
timer is guaranteed to increase monotonically between S-state changes.
changes to the package database, i.e. any packages that
have been added, updated or deleted in the past 24 hours.
The format is intentionally simple and concise.
That information is particularly useful on servers that
are maintained by multiple administrators. When someone
adds, updates or deletes a package, the others will see
it in the daily periodic output.
This script is disabled by default.
PR: conf/113913
Submitted by: olli
Approved by: des (mentor)
MFC after: 3 weeks
(in /etc/rc.conf).
This fixes an apparent confusion between test(1) and sh(1) syntax for
AND/OR.
PR: conf/149036
Submitted by: pluknet
MFC after: 1 week
This commit merges the latest LLVM sources from the vendor space. It
also updates the build glue to match the new sources. Clang's version
number is changed to match LLVM's, which means /usr/include/clang/2.0
has been renamed to /usr/include/clang/2.8.
Obtained from: projects/clangbsd
