and don't depend on them being declared there. This will cause lots of
warnings for a few minutes until config is updated. Interrupt handlers
should never have been configured by config, and the machine generated
declarations get in the way of changing the arg type from int to void *.
(mutant) Crystal CSS4236 chip on the Intel PR440FX SMP motherboard.
XXX this uses some rather ugly PnP bootstrap code that is *NOT* compatable
with 'controller pnp0' or *ANY* other PnP devices. If you use some other
PnP devices, enabling css0 will burn your house down. :-] The
"simplified" PnP init sequence directly blats your config(8) settings onto
the chip. I'm pretty sure 'css0' will conflict with 'mss0', this whole
area desperately needs a cleanup.
I have been using the following with some success on the PR440FX:
controller snd0
device css0 at isa? port 0x534 irq 5 drq 1 flags 0x08 vector adintr
device opl0 at isa? port 0x388
device mpu0 at isa? port 0x330 irq 10 vector mpuintr
Here are the remanding changes required to support the Ensoniq
Soundscape using FreeBSD 3.0-current.
Notes:
1) ad1848_init already has code to detect if DMA_DUPLEX should
be set so it is not necessary (and is in fact a mistake) to
hard code setting it. Not all soundcards (i.e. the current
sscape driver) are capable of using DMA_DUPLEX.
2) The other changes are hopefully self explanatory. Feel free
to let me know if you need additional information.
Submitted by: john@feith.com (John Wehle)
sys/pc98/i386/machdep.c: sync with i386/i386/machdep.c
sys/pc98/conf/options.pc98: sync with i386/conf/options.i386
sys/i386/isa/sound: DMA auto initialize mode support for PC98.
contributed by: Akio Morita <amorita@bird.scphys.kyoto-u.ac.jp>
Definite 2.2 material, I believe.
Submitted by: The FreeBSD (98) Development Team
Save 112K for SB, 64K for PAS and 64K for MSS.
Since PAS use SB emulation, 176K normally saved for it.
Few minor optimizations added like in Linux driver.
it out fixes my problem but hoses the GUS MAX probe messages. Check what
device we have and print things appropriately for each.
Pointed out by: Jim Lowe <james@miller.cs.uwm.edu>
whether of not to automatically #define EXCLUDE_AUDIO; MSS is a real
audio device and we should not #define EXCLUDE_AUDIO if we have one.
(And I want it because it's the only mixer-capable audio driver that I
can use with my crummy Packard Bell (nee Aztech) audio board.)
This fixes the very confusing condition where having all of this:
mss0 at 0x530 irq 10 drq 1 on isa
gus0: <MS Sound System (CS4231)>
opl0 at 0x388 on isa
opl0: <Yamaha OPL-3 FM>
mpu0 at 0x300 irq 9 drq 0 on isa
mpu0: <MPU-401 MIDI Interface 0.0 >
will still give you this:
% cat /dev/sndstat
SoundCard Error: The soundcard system has not been configured
Also remove an unnecessary newline in the printf() message for the
'gus0' device shown above so that we don't wind up printing a blank
line between mss0 and gus0.
Amancio. There is some SoundSource support here that is primitive and
probably doesn't work, but I'll let the two submitters let me know
how my integration of that was since I don't have this card to test.
I've only tested this on my GUS MAX since it's all I have.
This all probably needs to be re-done anyway since we're widely variant
from the original VOXWARE source in the current layout.
Submitted by: Amancio Hasty and Jim Lowe
Obtained from: Hannu Savolainen
with individual devices for each type of sound card:
opl, sb, sbxvi, sbmidi, pas, mpu, gus, gusxvi, gusmax, mss, uart
EXCLUDE_* options are no longer required to be included in the config file.
They are automatically determined by local.h depending on the devices
included.
Move #includes in local.h to os.h so files are included in the proper
order to avoid warnings.
soundcard.c now has additional code to reflect the device driver
routines needed.
Define new EXCLUDE_SB16MIDI for use in sb16_midi.c and dev_table.h.
#ifndef EXCLUDE_SEQUENCER or EXCLUDE_AUDIO have been added to
soundcard.c and sound_switch.c where appropriate.
Probe outputs changed to reflect new device names.
Readme.freebsd not needed. Update sound.doc with new config instructions.
Reviewed by: wollman
$Id$ information, and other code to make sound driver compile and work
correctly with FreeBSD.
Integrate changes obtained from Sujal Patel. These changes are:
o local.h: reverse option logic from EXCLUDE_* to AUDIO_*
o pas2_mixer.c: small addition
o ad1848.c: minor change with macro names
o sequencer.c: minor change with note check
o many spelling corrections in comments in about every other file
Make the sound configuration a little neater
(see /sys/i386/isa/sound/Readme.freebsd)
Add support for the Microsoft Sound Source.
Document the sound options again.
Submitted by: Sujal Patel <smpatel@wam.umd.edu>
Obtained from: Voxware
