works correctly in if/else etc. egcs had probably picked up most of the
problems here before with "ambiguous braces" etc, but this should
increase the robustness a bit. Based on an idea from Eivind Eklund.
out of the asm code, and as a bonus implements rtprio and idprio for the
Alpha. Previously if you ran an idprio process, you were assured of a
deadlock.
drop any segment arriving at a closed port.
tcp.blackhole=1 - only drop SYN without RST
tcp.blackhole=2 - drop everything without RST
tcp.blackhole=0 - always send RST - default behaviour
This confuses nmap -sF or -sX or -sN quite badly.
that goes to opt_dontuse.h is so an opt_*.h file doesn't get created even
though an option may be used for bringing stuff in via files[.*].
Pointed out by: bde
that are linked into the kernel. The KLD compilation options are
changed to call these functions, rather than in-lining the
atomic operations.
This approach makes atomic operations from KLDs significantly
faster on UP systems (though somewhat slower on SMP systems).
PR: i386/13111
Submitted by: peter.jeremy@alcatel.com.au
When you use pty(N) it creates pty(N+1) ready for your use in the DEVFS,
so DEVFS is not cluttered up with hundreds of ptys you are never going to
use.
about a dev_t.
printf("%x", dev) now becomes printf("%s", devtoname(dev)) because
printing actual information about the device is much more useful then
printing a pointer to an address that would never help the developer debug.
Submitted by: phk, bde
sysctl knobs.
With these knobs on, refused connection attempts are dropped
without sending a RST, or Port unreachable in the UDP case.
In the TCP case, sending of RST is inhibited iff the incoming
segment was a SYN.
Docs and rc.conf settings to follow.
didn't match the argument (p->p_pid).
While I'm at it, also fix the dupo in the format string and fix the annoying
inconsistency in all the debug-printfs wrt p_pid arguments. Change all of them
to use the %ld format specifier and cast the p_pid arguments to long.
Submitted by: billf
0x40 and then access data stored in real-mode segment 0x40, even when
called in protected mode. Microsoft unfortunately coddle these individuals,
and so must we if we want to run their code.
This change works around GPFs in some APM and PnP BIOS implementations.
Obtained from: Linux
messages, abort messages, and abort tag messages.
Fix a bug in how default transfer negotiations are handled if the
user had disabled initial bus resets.
Support multi-targetid on the aic7895C.
Handle errors reported through immediate notify ccbs. This includes
bus resets, BDR messages, and abort messages.
Properly setup CA conditions for errors such as uncorectable parity
in data phases, reselection failure, and IDE message received.
Add a mechanism for stalling the queue of transactions to a particular
initiator while a CA is in progress. Since we don't yet support
tagged I/O, this is largely just for show right now.
Properly bzero our softc at init time (oops).
Add more documentation on what all of the queues in our softc do.
Clear residuals for XPT_TARGET_IO/XPT_CONT_TARGET_IO calls just
as we do for XPT_SCSI_IO calls.
Make xpt_release_devq a proper reciprocal of xpt_freeze_devq by
allowing the caller to decrement the count more than once per call.
Change the semantics of xpt_path_cmp to return 1 for a match
with a wildcard from path1 and 2 for a match with wildcards
from path2. This change doesn't affect most callers as they
only check for >=0 (exact match or one containing a wildcard).
When cleaning up a device node, ensure that there are no timeouts
outstanding that reference it.
mechanism should be completely revamped, but this will serve for the time
being.
Take advantage of some new behavior in xpt_path_comp which allows the
caller to determine which path, if any, had wildcards in it that allowed
for a match to succeed. We can now use this to filter out wildcard
nodes in the EDT.
Make the amount of time we pause after writing a debug message
configurable.
on physical devices as oposed to just in the XPT. This is used to
mark XPT_SCSI_IO, XPT_RESET_DEV, XPT_ENG_EXEC, XPT_TARGET_IO, and
XPT_CONT_TARGET_IO function codes.
Change tag_id and init_id to be u_int from u_int8_t. Some topologies
supported by CAM support much larger ID and tag ID address spaces
than parallel SCSI.
Kill some unused fields in the IMMED_NOTIFY ccb type.
the attach/detach to
1) MOD_LOAD before attach
2) MOD_UNLOAD after detach
The driver specific event handler can now be used to function as
driver specific init/deinit function (compare to device specific
init/deinit functions: attach & detach).
Remove semicolons or add "do { } while (0)" as necessary
to enable the use of these macros in arbitrary statements.
(There are no functional changes.)
Submitted by: dillon
is quirked for allowing it. This will allow SCSI cards to specify their true
correct lun width (32 for Qlogic SCSI, 16 or 65536 for Qlogic Fibre Channel)
without crippling the system because of f/w breakage of a lot of drives.
Reviewed by: gibbs@freebsd.org
format_config: code preening.
vinum_scandisk: If we find a partition in the first pass over a drive,
note the fact so we don't grab the compatibility partition as well.
Submitted-by: peter
the aic7890/91/96/97 cards. This could cause the system to go into
a long retry/recovery loop during probe.
Fix the alignment argument to bus_dma_tag_create().
Don't set the CACHETHEN bit in dscommand0 for Ultra2 controllers
until we know more about its behavior. The description for this
bit makes it sound like it could cause problems with certain
PCI chipsets.
The first reason for this rewrite is KNF conformance.
The second reason is to avoid redundancy. Each function printed the same
string, with only the syscall name being different. The actual printing is now
performed by a single function, which gets the syscall name as an argument.
The third reason is that of convenience. It's now very easy to add a new
dummy implementation. Just add ``DUMMY(foo);'' to the file. It's also a lot
easier now to see if a syscall has a dummy implementation or not.
The dummies are ordered on syscall number. Please maintain this when adding
new dummies (there're 32 candidates at the time of writing :-)
Reviewed by: bde
prototypes of o{s|g}etrlimit (from sys/sysproto.h). Update linux_{s|g}etrlimit
so that the arguments to o{s|g}etrlimit are corresponding the prototypes.
Pointed out by: bde
- Sort xrefs
- FreeBSD.ORG -> FreeBSD.org
- Be consistent with section names as outlines in mdoc(7)
- Other misc mdoc cleanup.
PR: doc/13144
Submitted by: Alexy M. Zelkin <phantom@cris.net>
goes into initialized state, not 'up'. This makes it easier to ensure
consistency in multi-plex volumes.
update_plex_state: redo transitions from empty and initialized
subdisks to up or reviving, depending on the number of plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
apm_bioscall() to check requested BIOS is supported or not.
- Add workaround in apm_driver_version() for the buggy BIOSes which
don't return the connection version in %ax.
PR: i386/13028
Reviewed by: sanpei@sanpei.org and Warner Losh.
functions use the new sigset_t and sigaction_t which allows support for more
than 32 signals. Only the lower 32 signals are supported for now.
linux_rt_sigaction, linux_sigaction and linux_signal use linux_do_sigaction
to do the actual work. That way unnecessary redundancy is avoided. The same
has been done for linux_rt_sigprocmask and linux_sigprocmask. They call
linux_do_sigprocmask to do the actual work.
the SRM environment. This makes the traditional "boot [/kernel] -s"
and similar things work on the Alpha. Since the flags are appended,
they augment and/or override those from the SRM environment.
of kernel space. Remove the ioctl supporting functions, and move the actual
code to the switch-statement. Now everybody can clearly see that the
implementation is really poor.
Also fix a typo in LINUX_TIOCGETD. The underlying function was given command
TIOCSETD instead op TIOCGETD...
Introduce BUF_STRATEGY(struct buf *, int flag) macro, and use it throughout.
please see comment in sys/conf.h about the flag argument.
Remove strategy argument from all the diskslice/label/bad144
implementations, it should be found from the dev_t.
Remove bogus and unused strategy1 routines.
Remove open/close arguments from dssize(). Pick them up from dev_t.
Remove unused and unfinished setgeom support from diskslice/label/bad144 code.
changes. This is part 1 of the complete termios ioctl fixes.
o change type of c_{i|o|c|l}flag in struct termios from unsigned long to
unsigned int. The type now matches the Linux definitions.
o replaced constants by the corresponding defines in sptab[] for clarity.
Since there's no define for 135 baud, its mapping has been dropped.
function bsd_to_linux_termios:
o Fix typo IXON -> IXANY.
o Remove bogus assignment to c_cc[LINUX_VSWTC].
function linux_to_bsd_termios:
o Fix dupo LINUX_IXON -> LINUX_IXANY.
o Add LINUX_CREAD mapping.
o Fix typo IEXTEN -> LINUX_IEXTEN.
function linux_to_bsd_termio:
o Small optimization: Don't preset the complete c_cc array when we next
assign to the first LINUX_NCC entries.
Don't return "can't do it" when the user requests a state change to
the current state. This previously caused silly messages like "Can't
start <foo>: invalid argument", when in fact <foo> was already
started.
set_plex_state: don't set state for non-existent plexes.
update_plex_status: as long as we have initializing subdisks, we're
initializing.
Move the declaration of freerq() to request.h.
logrq: add support for lock events.
vinumstart: solve a problem where removing a plex from an active
volume could cause attempts to access non-existent plexes.
launch_requests: don't set a request group active until we're sure we
can launch it. This caused some hangs under unusual
circumstances.
bre: don't set XFR_BAD_SUBDISK if we're not going to use it.
build_read_request: correct recovery, which caused some hangs under
(other) unusual circumstances.
build_rq_buffer: don't set bp->b_dev if we don't have a dev.
sdio: clean up, remove obsolete code.
deallocrqg: unlock any locks the rqg may have.
bre5:
Shorten some lines.
Desired-by: bde
If we're reading from a short plex, return EOF indication.
Always lock the stripe before starting a transfer. Hopefully the
current version will solve some data integrity problems that have
been reported with degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
solve some data integrity problems that have been reported with
degraded RAID-5 plexes.
Reported-by: Bernd Walter <ticso@cicely.de>
Remy Nonnenmacher <remy@synx.com>
Tidy other comments.
open_drive: don't call set_drive_state if we decide to take it down.
This could help avoid some race conditions with the daemon.
init_drive: don't set the drive down, we'll let close_locked_drive do
that.
close_locked_drive: set drive state to down without calling
set_drive_state. This could help avoid some race conditions with the
daemon.
driveio: remove the function, it wasn't being used.
get_volume_label: remove volume dependencies so that we can return a
label for plexes and subdisks as well. What a kludge.
Remove declarations for freerq and free_rqg.
Remove DEBUG_RESID code.
freerq: check whether the request is holding a lock, free if so.
free_rqg: remove. It wasn't being used any more.
Change the Debugger calls to panics.
checkdiskconfig(): remove. It didn't make any sense to complain about
kernel keywords in user config files; it just made it more difficult
to convert. Now we ignore kernel keywords if we're not in kernel
mode.
get_empty_sd: initialize sectors.
free_drive: don't close if we don't have a vp. Maybe this will help
fix the problem that peter had, but I wouldn't count on it.
config_plex: If the plex is RAID-5, give it a rangelock structure.
start_config: Reset current drive, plex and volume so that a new
'create' command doesn't get long-dead defaults.
struct rqelement, enum rqinfo_type, struct rqinfo, union rqinfou: add
lock requests.
Add declarations for freerq and unlockrange. Since they include
request structures, they can't go in vinumext.h
stuff: unregister_methods() is horribly broken. The idea, if I'm not mistaken,
is that the refcount on a method is decremented, and only when it reaches
zero is the method freed. However desc->method is set to NULL unconditionally
regardless of the refcount, which means the method pointer is trashed the
first time the method is deallocated. The obvious detrimental effect is
that memory is leaked. The not so obvious effect is that when you call
unregister_method() the second time on the same method, you get a NULL
pointer dereference and a panic.
Now I can successfully unload network device drivers and the miibus module
without crashing the system.
*sigh*
A complete rewrite by dillon and myself to separate
the implementation of behaviors that effect the vm_map_entry
from those that effect the vm_object.
A result of this change is that madvise(..., MADV_FREE);
is much cheaper.
operations. This allows a device driver better insight into
what is going on that the current:
proc1: open /dev/foo R/O
devsw->open( R/O, proc1 )
proc2: open /dev/foo R/W
devsw->open( R/W, proc2 )
proc2: close
/* nothing, but device is
really only R/O open */
proc1: close
devsw->close( R/O, proc1 )
in deterministic behaviour. In this case known garbage out.
The fix is different than suggested in the PR.
PR: 12749
Originator: Boris Nikolaus <boris@cs.tu-berlin.de>
This setting is also acceptable for Celerons and Pentium Pros
with less than 1MB L2 caches.
Note: PQ_L2_SIZE is a misnomer. The correct number of colors is
a function of the cache's degree of associativity as well as its size.
Submitted by: bde and alc
with a match probability to achieve non-deterministic behaviour of
the firewall. This can be extremely useful for testing purposes
such as simulating random packet drop without having to use dummynet
(which already does the same thing), and simulating multipath effects
and the associated out-of-order delivery (this time in conjunction
with dummynet).
The overhead on normal rules is just one comparison with 0.
Since it would have been trivial to implement this by just adding
a field to the ip_fw structure, I decided to do it in a
backward-compatible way (i.e. struct ip_fw is unchanged, and as a
consequence you don't need to recompile ipfw if you don't want to
use this feature), since this was also useful for -STABLE.
When, at some point, someone decides to change struct ip_fw, please
add a length field and a version number at the beginning, so userland
apps can keep working even if they are out of sync with the kernel.
"the device doesn't support a dump routine"
Only print "dump succeeded" when 0 is returned, instead of when an unexpected
error number is returned, print that error number.
Reviewed by: Eivind
The linux syscalls translate the arguments first before invoking the
FreeBSD native syscalls.
PR: kern/9591
Originator: John Plevyak <jplevyak@inktomi.com>
a module. Also modified the code to work on FreeBSD/alpha and added
device vr0 to the alpha GENERIC config.
While I was in the neighborhood, I noticed that I was still using
#define NFPX 1 in all of the Makefiles that I'd copied from the fxp
module. I don't really use #define Nfoo X so it didn't matter, but
I decided to customize this correctly anyway.
respectively logging and dropping ICMP REDIRECT packets.
Note that there is no rate limiting on the log messages, so log_redirect
should be used with caution (preferrably only for debugging purposes).
as PCI->HOST bridges on my (440BX) box.
My change is to remove the test at the beginning entirely, letting the
switch on the device ID happen first. If the device ID is unknown, then
(in the default case) check for the generic PCIS_BRIDGE_HOST tag. This
should allow wierd cases (eg: wpaul's IMS VL bridge) to work by using the
id override. This strategy is more in line with the other PCI match
methods we use elsewhere,
I only have a limited testbed, but having my USB etc devices detected as
PCI->HOST bridges doesn't look good.
1) Safty change from casper dik was added to OpenBSD's sources since I
grabbed them. milltert@openbsd.org
2) Split up strlcpy to improve efficiency of the common case.
milltert@openbsd.org
3) Cleanup of cross references for man page. {alex,aaron}@openbsd.org
Pointed out by: deraadt@openbsd.org
Now that behaviors are stored in the vm_map_entry rather than
the vm_object, it's no longer necessary to instantiate a vm_object
just to hold the behavior.
Reviewed by: dillon
correctly. It has the following code:
if (class != PCIC_BRIDGE || subclass != PCIS_BRIDGE_HOST)
return NULL;
My 486 has an Integrated Micro Solutions PCI bridge which identifies
itself as subclass PCIS_BRIDGE_OTHER, not PCIS_BRIDGE_HOST. Consequently,
it gets ignored. In my opinion, the correct test should be:
if ((class != PCIC_BRIDGE) && (subclass != PCIS_BRIDGE_HOST))
return NULL;
That way the test still succeeds because the chip's class is PCIC_BRIDGE.
Clearly it's not reasonable to expect all host to PCI bridges to always
have a subclass of PCIS_BRIDGE_HOST since I've got one that doesn't.
This way the sanity test should remain relatively sane while still allowing
some oddball yet correct hardware to work. If somebody has a better way
to do it, go ahead and tweak the test, but be aware that
class == PCIC_BRIDGE and subclass == PCIS_BRIDGE_OTHER is a valid case.
While I was here, I also added an explicit ID string for the IMS chipset.
I also dealt with a minor style nit: it's bad karma not to have a default
case for your switch statements, but the one in this routine doesn't have
one. The default string of "Host to PCI bridge" is now assigned in a
default case of the switch statement instead of initializing "s" with the
string before the switch and then not having any default case.
Isn't really that useful.
chip0: <PCI to Other bridge (vendor=10e0 device=8849)> at device 0.0 on pci0
is more in keeping with the spirit of the rest of the code.
Previous behavior with regard to truely unknown bridges unchanged.
"<Anti-Bill> Tell you what: you have commit privs now. You do it."
Config(8) contains no documentation about this.
Fix the help for the PnP irq and drq commands. This one caused
me a bit of head scratching the other night while trying to get
a problematic PnP device configured properly.
