If a jail has an explicitly assigned IPv6 loopback address then allow it
to be used instead of remapping requests for the loopback adddress to the
first IPv6 address assigned to the jail.
This fixes issues where applications attempt to detect their bound port
where they requested a loopback address, which was available, but instead
the kernel remapped it to the jails first address.
This is the same fix applied to IPv4 fix by: r316313
Also:
* Correct the description of prison_check_ip6_locked to match the code.
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Multiplay
If a jail has an explicitly assigned loopback address then allow it to be
used instead of remapping requests for the loopback adddress to the first
IPv4 address assigned to the jail.
This fixes issues where applications attempt to detect their bound port
where they requested a loopback address, which was available, but instead
the kernel remapped it to the jails first address.
A example of this is binding nginx to 127.0.0.1 and then running "service
nginx upgrade" which before this change would cause nginx to fail.
Also:
* Correct the description of prison_check_ip4_locked to match the code.
MFC after: 2 weeks
Relnotes: Yes
Sponsored by: Multiplay
the default partition, eMMC v4.41 and later devices can additionally
provide up to:
1 enhanced user data area partition
2 boot partitions
1 RPMB (Replay Protected Memory Block) partition
4 general purpose partitions (optionally with a enhanced or extended
attribute)
Of these "partitions", only the enhanced user data area one actually
slices the user data area partition and, thus, gets handled with the
help of geom_flashmap(4). The other types of partitions have address
space independent from the default partition and need to be switched
to via CMD6 (SWITCH), i. e. constitute a set of additional "disks".
The second kind of these "partitions" doesn't fit that well into the
design of mmc(4) and mmcsd(4). I've decided to let mmcsd(4) hook all
of these "partitions" up as disk(9)'s (except for the RPMB partition
as it didn't seem to make much sense to be able to put a file-system
there and may require authentication; therefore, RPMB partitions are
solely accessible via the newly added IOCTL interface currently; see
also below). This approach for one resulted in cleaner code. Second,
it retains the notion of mmcsd(4) children corresponding to a single
physical device each. With the addition of some layering violations,
it also would have been possible for mmc(4) to add separate mmcsd(4)
instances with one disk each for all of these "partitions", however.
Still, both mmc(4) and mmcsd(4) share some common code now e. g. for
issuing CMD6, which has been factored out into mmc_subr.c.
Besides simply subdividing eMMC devices, some Intel NUCs having UEFI
code in the boot partitions etc., another use case for the partition
support is the activation of pseudo-SLC mode, which manufacturers of
eMMC chips typically associate with the enhanced user data area and/
or the enhanced attribute of general purpose partitions.
CAVEAT EMPTOR: Partitioning eMMC devices is a one-time operation.
- Now that properly issuing CMD6 is crucial (so data isn't written to
the wrong partition for example), make a step into the direction of
correctly handling the timeout for these commands in the MMC layer.
Also, do a SEND_STATUS when CMD6 is invoked with an R1B response as
recommended by relevant specifications. However, quite some work is
left to be done in this regard; all other R1B-type commands done by
the MMC layer also should be followed by a SEND_STATUS (CMD13), the
erase timeout calculations/handling as documented in specifications
are entirely ignored so far, the MMC layer doesn't provide timeouts
applicable up to the bridge drivers and at least sdhci(4) currently
is hardcoding 1 s as timeout for all command types unconditionally.
Let alone already available return codes often not being checked in
the MMC layer ...
- Add an IOCTL interface to mmcsd(4); this is sufficiently compatible
with Linux so that the GNU mmc-utils can be ported to and used with
FreeBSD (note that due to the remaining deficiencies outlined above
SANITIZE operations issued by/with `mmc` currently most likely will
fail). These latter will be added to ports as sysutils/mmc-utils in
a bit. Among others, the `mmc` tool of the GNU mmc-utils allows for
partitioning eMMC devices (tested working).
- For devices following the eMMC specification v4.41 or later, year 0
is 2013 rather than 1997; so correct this for assembling the device
ID string properly.
- Let mmcsd.ko depend on mmc.ko. Additionally, bump MMC_VERSION as at
least for some of the above a matching pair is required.
- In the ACPI front-end of sdhci(4) describe the Intel eMMC and SDXC
controllers as such in order to match the PCI one.
Additionally, in the entry for the 80860F14 SDXC controller remove
the eMMC-only SDHCI_QUIRK_INTEL_POWER_UP_RESET.
OKed by: imp
Submitted by: ian (mmc_switch_status() implementation)
Since the state name is an optional argument, it often can conflict
with other options. To avoid ambiguity now the state name must be
prefixed with a colon.
Obtained from: Yandex LLC
MFC after: 2 week
Sponsored by: Yandex LLC
Some of the modifications from the previous summer of code has been integrated
Modification for compatibility with GNU diff output has been added
Main difference with OpenBSD:
Implement multiple GNU diff options:
* --ignore-file-name-case
* --no-ignore-file-name-case
* --normal
* --tabsize
* --strip-trailing-cr
Make diff -p compatible with GNU diff
Implement diff -l
Make diff -r compatible with GNU diff
Capsicumize diffing 2 regular files
Add a simple test suite
Approved by: AsiaBSDcon devsummit
Obtained from: OpenBSD, GSoC
Relnotes: yes
Bring back the i486 option in GENERIC by default.
The code related to i386 CPU variants configuration has received many
changes in the last years: most of the features are detected automatically,
so there are no performance penalties from keeping the 486 support enabled.
Re-instate the 486 support: while the general configuration could still be
cleaned a bit, there is no advantage in removing it.
Differential Revision: https://reviews.freebsd.org/D9879
- em(4) igb(4) and lem(4)
- deprecate the igb device from kernel configurations
- create a symbolic link in /boot/kernel from if_em.ko to if_igb.ko
Devices tested:
- 82574L
- I218-LM
- 82546GB
- 82579LM
- I350
- I217
Please report problems to freebsd-net@freebsd.org
Partial review from jhb and suggestions on how to *not* brick folks who
originally would have lost their igbX device.
Submitted by: mmacy@nextbsd.org
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Limelight Networks and Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D8299
vmpage requires struct pmap to exist and contain a pm_stats field. As of
r308817, either AIM or BOOKE is required to be set in order to get their
respective pmap structs. Rather than expose them both, or try to unify them
unnecessarily, add a third option which contains only a pm_stats field, and
change the two existing pmap structures to place the common fields at the
beginning of the struct. This actually fixes the stats collection by libkvm on
AIM hardware, because before it was accessing a possibly different offset, which
would cause it to read garbage.
Bump __FreeBSD_version to denote this ABI change, so that ports which depend on
libkvm can be rebuilt.
Summary:
The hardware does not expose a classic SMBus interface.
Instead it has a lower level interface that can express a far richer
I2C protocol than what smbus offers. However, the interface does not
provide a way to explicitly generate the I2C stop and start conditions.
It's only possible to request that the stop condition is generated
after transferring the next byte in either direction. So, at least
one data byte must always be transferred.
Thus, some I2C sequences are impossible to generate, e.g., an equivalent
of smbus quick command (<start>-<slave addr>-<r/w bit>-<stop>).
At the same time isl(4) and cyapa(4) are moved to iicbus and now they use
iicbus_transfer for communication. Previously they used smbus_trans()
interface that is not defined by the SMBus protocol and was implemented
only by ig4(4). In fact, that interface was impossible to implement
for the typical SMBus controllers like intpm(4) or ichsmb(4) where
a type of the SMBus command must be programmed.
The plan is to remove smbus_trans() and all its uses.
As an aside, the smbus_trans() method deviates from the standard,
but perhaps backwards, FreeBSD convention of using 8-bit slave
addresses (shifted by 1 bit to the left). The method expects
7-bit addresses.
There is a user facing consequence of this change.
A user must now provide device hints for isl and cyapa that specify an iicbus to use
and a slave address on it.
On Chromebook hardware where isl and cyapa devices are commonly found
it is also possible to use a new chromebook_platform(4) driver that
automatically configures isl and cyapa devices. There is no need to
provide the device hints in that case,
Right now smbus(4) driver tries to discover all slaves on the bus.
That is very dangerous. Fortunately, the probing code uses smbus_trans()
to do its job, so it is really enabled for ig4 only.
The plan is to remove that auto-probing code and smbus_trans().
Tested by: grembo, Matthias Apitz <guru@unixarea.de> (w/o
chromebook_platform)
Discussed with: grembo, imp
Reviewed by: wblock (docs)
MFC after: 1 month
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D8172
prominently. Unlike in the past (dating back to the 4.x branch point),
you cannot upgrade from any point on the past couple of stable
branches to -current. Due to a bug in clang that existed before
r286035 in stable/9 or r286033 in stable/10, we cannot compile llvm
that's in 11.x or -current. Unfortunately, these revisions are after
9.3R and 10.3R on their respective branches. stable/11 and 11.0R are
not affected.
This also affects the upgrade path to 11 (including 11.0R) from
stable/9 and stable/10 (which would otherwise work, were it not for
this bug).
We also need to amend the 11.0R release notes.
MFC After: 3 days
GNU rcs is still available as a package:
- rcs: Latest GPLv3 GNU rcs version.
- rcs57: Copy of the latest version of GNU rcs (GPLv2) from base.
Relnotes: yes
to add actions that run when a TCP frame is sent or received on a TCP
session in the ESTABLISHED state. In the base tree, this functionality is
only used for the h_ertt module, which is used by the cc_cdg, cc_chd, cc_hd,
and cc_vegas congestion control modules.
Presently, we incur overhead to check for hooks each time a TCP frame is
sent or received on an ESTABLISHED TCP session.
This change adds a new compile-time option (TCP_HHOOK) to determine whether
to include the hhook(9) framework for TCP. To retain backwards
compatibility, I added the TCP_HHOOK option to every configuration file that
already defined "options INET". (Therefore, this patch introduces no
functional change. In order to see a functional difference, you need to
compile a custom kernel without the TCP_HHOOK option.) This change will
allow users to easily exclude this functionality from their kernel, should
they wish to do so.
Note that any users who use a custom kernel configuration and use one of the
congestion control modules listed above will need to add the TCP_HHOOK
option to their kernel configuration.
Reviewed by: rrs, lstewart, hiren (previous version), sjg (makefiles only)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D8185
In FreeBSD 11 ELF Tool Chain's elfcopy is installed as objcopy by
default, with the option to switch back to GNU objcopy by setting
WITHOUT_ELFCOPY_AS_OBJCOPY in make.conf.
We plan to remove the outdated in-tree binutils in FreeBSD 12, so
remove the temporary transition aid.
Reviewed by: brooks, imp
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7337
All remaining tools using rcs has been switched to directly use diff3(1):
- etcupdate(8)
- freebsd-update(8)
Note that the ident(1) tool is been already replaced long ago with a BSD
licensed version, as such it remains installed.
GNU rcs is still available from ports:
- rcs: newer GPLv3 version
- rcs57: the latest version from base (GPLv2)
In preparation for the removal of GNU rcs from base, remove the backup_uses_rcs
functionality from the rc.subr backup_file feature. This functionnality was off
by default
Reviewed by: wblock
Differential Revision: https://reviews.freebsd.org/D7883
Split the QUEUE_MACRO_DEBUG into QUEUE_MACRO_DEBUG_TRACE and
QUEUE_MACRO_DEBUG_TRASH.
Add the debug macrso QMD_IS_TRASHED() and QMD_SLIST_CHECK_PREVPTR().
Document these in queue.3.
Reviewed by: emaste
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D3984
in_broadcast() can be quite expensive, so skip calling it if the
incoming mbuf wasn't sent to a broadcast L2 address in the first
place.
Reviewed by: gnn
MFC after: 2 months
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D7309
