algorithm is used on aic7770 Rev E or higher chips to improve perfomance.
This required a hardware change but we don't know exactly what (most
likely some special register to do fast SCB indexing into host memory),
and we are not at all sure that there are more than 4 SCBs on these
chips. This probe will still classify the revision of the aic7xxx, but
we now default to 4 SCBs (at least until we know more of what was done).
This also fixes a bug in the timeout routine where we cleared a flag
too soon making it imposible to enter one section of the routine.
Submitted by: Timeout bug - Dan Eischen <deischen@iworks.InterWorks.org>
interrupts to zero to start with. This is the value we return in
most cases. The sense code then outbs the apropriate value to cause
sense retrieval. The return value was uninitialized before this
change (something that was an okay thing with the old sequencer code,
but not with the semantics of the new).
This problem caused us to always retrieve sense upon recieving a non
zero status byte. This is exactly what was happening for the "target
busy" status returned by exabyte tape drives when they rewind or
power on with a tape installed. The request sense proved fatal.
This should fix the tape problems.
It is the kernel driver's responsibility to do the list manipulation whenever
a selection timeout or a request sense occurs.
Print out the interrupt type that the device has been set to. It seems that
one of the Asus motherboards botches this and David thought a diagnostic would
be nice.
Fix a bug in my diagnostic code that David found.
Reviewed by: Wcarchive and David Greenman
higher level scsi code.
Spls should never be conditionalized, so don't do so here.
Restructure the get_scb routine so that we can't get into an infinite
loop if the ccbs are exhausted and we are are called with SCSI_NOSLEEP set.
Other driver maintainer's that based their scb allocation routines on Julian's
code should look at these changes and implement them for their driver.
The aic7xxx driver inspired these changes because early revs of the
aic7770 chips have so few SCBs that you can actually run out. If you
have a rev C or aic7770 (as is reported by the driver probe) and had more
than 2 drives, you could get into an infinite loop when using up all of
the SCBs. Since the driver will only allow two SCBs per device and I
only had two devices, I never saw this problem on my Rev C card.
Bzero only 19 bytes of the scb instead of 2k (ack!). This was a hold
over from when a struct SCB only contained the information downloaded
to the board, but we now store kernel driver data in there as well. This
greatly lowers the overhead for small transactions (I get ~1MB/sec for
dds with a 512 byte block size).
Submitted by: John Dyson with the aic7xxx specific optimization by me
When attempting to abort a command, don't assume that just because the
sequecer happens to have SCBPTR pointing at the scb we want that it is
an active command.
- catch the interrupt type (EDGE/LEVEL) before chip reset instead
of guessing the right type.
- Add pause variable to the ahc struct to better handle the different
interrupt types and pausing the sequencer.
- CLRINTSTAT -> CLRSCSIINT: This is a documented bit in the CLRINT
register in newer Adaptec documentation, so use their name for it.
- Report valid residual byte counts.
- Don't mess with the target scratch areas > id 8 on single, narrow,
channel devices. The BIOS does a checksum of this area and can
flip out if we zero it out.
- Initialize the sequencer FLAGS scratch ram variable in the single
channel devices to 0. This was the cause of the annoying warning
where we would get a cmdcmplt the first time we did any type of
transfer negotiation with no valid scb. It also fixes the problem
that looked like the INTSTAT register wasn't clearing fast enough.
This only showed up on 294x cards, not motherboard aic7870s.
- Add the AHC_AIC7870 type and use it as the superset of aic7870
based controllers.
- clear the sync offset section of the targ scratch area so that
we default to asyncronous transfers. This was only a problem
for wide controllers because there was a scenario where the
offset wouldn't get updated before a data(out/in) phase would
occur. This required some change in the sequencer code since we
were depending on this field to hold the rate to negotiate.
- allow sync and wide negotiated commands to be tagged (the sequencer
now handles this properly).
probe of the device and shouldn't affect normal operation. It seems that
some version of the aic7870 are extreamly slow in clearing their interrupt
register so the added delay is required to ensure we don't poll a stale
interrupt value.
Clean up debugging printfs and stuff superflous output into #ifdef AHC_DEBUG.
Ensure that sdtrpending and wdtrpending are cleared in all cases after
we recieve an SDTR or WDTR message.
With this commit, the 294x should work or at least be much closer to
working properly.
commands per target. I could have followed the route of the ncr driver
and gone to great lengths to get the SCSI subsystem to support more, but
I think I'll use the time saved to help Julian and Peter make tagged
queuing a better handled generic feature. This also includes some comment
and enum clean up and a possible fix for the hanging PCI controllers.
message instead of relying on the fact that we are scheduled to send them.
The old method worked 99.9% of the time, but someone reported some periferals
that did MSG_REJECT at odd times (sometimes before we could send an SDTR
or WDTR) that we would construe as the response to an SDTR or WDTR message.
This also removes a possible race condition where after a bus reset (the
result of a command time out not during intial probe time), we might queue
two commands both requesting SDTR, WDTR or both.
WDTR, and message reject handlers so they don't need to exist in the
sequencer. All three of these cases are not on the critical path, so it
makes little sense to use up precious sequencer ram for them.
values for syncronous negotiation. The 284x series adaptors can now be
supported without the Bios being enabled. If you disable the Bios on the
274x series adaptors, all configuration parameters revert to the default
since there is no way to retrieve them.
