This particular implementation is designed to be fully backwards compatible
and to be MFC-able to 7.x (and 6.x)
Currently the only protocol that can make use of the multiple tables is IPv4
Similar functionality exists in OpenBSD and Linux.
From my notes:
-----
One thing where FreeBSD has been falling behind, and which by chance I
have some time to work on is "policy based routing", which allows
different
packet streams to be routed by more than just the destination address.
Constraints:
------------
I want to make some form of this available in the 6.x tree
(and by extension 7.x) , but FreeBSD in general needs it so I might as
well do it in -current and back port the portions I need.
One of the ways that this can be done is to have the ability to
instantiate multiple kernel routing tables (which I will now
refer to as "Forwarding Information Bases" or "FIBs" for political
correctness reasons). Which FIB a particular packet uses to make
the next hop decision can be decided by a number of mechanisms.
The policies these mechanisms implement are the "Policies" referred
to in "Policy based routing".
One of the constraints I have if I try to back port this work to
6.x is that it must be implemented as a EXTENSION to the existing
ABIs in 6.x so that third party applications do not need to be
recompiled in timespan of the branch.
This first version will not have some of the bells and whistles that
will come with later versions. It will, for example, be limited to 16
tables in the first commit.
Implementation method, Compatible version. (part 1)
-------------------------------
For this reason I have implemented a "sufficient subset" of a
multiple routing table solution in Perforce, and back-ported it
to 6.x. (also in Perforce though not always caught up with what I
have done in -current/P4). The subset allows a number of FIBs
to be defined at compile time (8 is sufficient for my purposes in 6.x)
and implements the changes needed to allow IPV4 to use them. I have not
done the changes for ipv6 simply because I do not need it, and I do not
have enough knowledge of ipv6 (e.g. neighbor discovery) needed to do it.
Other protocol families are left untouched and should there be
users with proprietary protocol families, they should continue to work
and be oblivious to the existence of the extra FIBs.
To understand how this is done, one must know that the current FIB
code starts everything off with a single dimensional array of
pointers to FIB head structures (One per protocol family), each of
which in turn points to the trie of routes available to that family.
The basic change in the ABI compatible version of the change is to
extent that array to be a 2 dimensional array, so that
instead of protocol family X looking at rt_tables[X] for the
table it needs, it looks at rt_tables[Y][X] when for all
protocol families except ipv4 Y is always 0.
Code that is unaware of the change always just sees the first row
of the table, which of course looks just like the one dimensional
array that existed before.
The entry points rtrequest(), rtalloc(), rtalloc1(), rtalloc_ign()
are all maintained, but refer only to the first row of the array,
so that existing callers in proprietary protocols can continue to
do the "right thing".
Some new entry points are added, for the exclusive use of ipv4 code
called in_rtrequest(), in_rtalloc(), in_rtalloc1() and in_rtalloc_ign(),
which have an extra argument which refers the code to the correct row.
In addition, there are some new entry points (currently called
rtalloc_fib() and friends) that check the Address family being
looked up and call either rtalloc() (and friends) if the protocol
is not IPv4 forcing the action to row 0 or to the appropriate row
if it IS IPv4 (and that info is available). These are for calling
from code that is not specific to any particular protocol. The way
these are implemented would change in the non ABI preserving code
to be added later.
One feature of the first version of the code is that for ipv4,
the interface routes show up automatically on all the FIBs, so
that no matter what FIB you select you always have the basic
direct attached hosts available to you. (rtinit() does this
automatically).
You CAN delete an interface route from one FIB should you want
to but by default it's there. ARP information is also available
in each FIB. It's assumed that the same machine would have the
same MAC address, regardless of which FIB you are using to get
to it.
This brings us as to how the correct FIB is selected for an outgoing
IPV4 packet.
Firstly, all packets have a FIB associated with them. if nothing
has been done to change it, it will be FIB 0. The FIB is changed
in the following ways.
Packets fall into one of a number of classes.
1/ locally generated packets, coming from a socket/PCB.
Such packets select a FIB from a number associated with the
socket/PCB. This in turn is inherited from the process,
but can be changed by a socket option. The process in turn
inherits it on fork. I have written a utility call setfib
that acts a bit like nice..
setfib -3 ping target.example.com # will use fib 3 for ping.
It is an obvious extension to make it a property of a jail
but I have not done so. It can be achieved by combining the setfib and
jail commands.
2/ packets received on an interface for forwarding.
By default these packets would use table 0,
(or possibly a number settable in a sysctl(not yet)).
but prior to routing the firewall can inspect them (see below).
(possibly in the future you may be able to associate a FIB
with packets received on an interface.. An ifconfig arg, but not yet.)
3/ packets inspected by a packet classifier, which can arbitrarily
associate a fib with it on a packet by packet basis.
A fib assigned to a packet by a packet classifier
(such as ipfw) would over-ride a fib associated by
a more default source. (such as cases 1 or 2).
4/ a tcp listen socket associated with a fib will generate
accept sockets that are associated with that same fib.
5/ Packets generated in response to some other packet (e.g. reset
or icmp packets). These should use the FIB associated with the
packet being reponded to.
6/ Packets generated during encapsulation.
gif, tun and other tunnel interfaces will encapsulate using the FIB
that was in effect withthe proces that set up the tunnel.
thus setfib 1 ifconfig gif0 [tunnel instructions]
will set the fib for the tunnel to use to be fib 1.
Routing messages would be associated with their
process, and thus select one FIB or another.
messages from the kernel would be associated with the fib they
refer to and would only be received by a routing socket associated
with that fib. (not yet implemented)
In addition Netstat has been edited to be able to cope with the
fact that the array is now 2 dimensional. (It looks in system
memory using libkvm (!)). Old versions of netstat see only the first FIB.
In addition two sysctls are added to give:
a) the number of FIBs compiled in (active)
b) the default FIB of the calling process.
Early testing experience:
-------------------------
Basically our (IronPort's) appliance does this functionality already
using ipfw fwd but that method has some drawbacks.
For example,
It can't fully simulate a routing table because it can't influence the
socket's choice of local address when a connect() is done.
Testing during the generating of these changes has been
remarkably smooth so far. Multiple tables have co-existed
with no notable side effects, and packets have been routes
accordingly.
ipfw has grown 2 new keywords:
setfib N ip from anay to any
count ip from any to any fib N
In pf there seems to be a requirement to be able to give symbolic names to the
fibs but I do not have that capacity. I am not sure if it is required.
SCTP has interestingly enough built in support for this, called VRFs
in Cisco parlance. it will be interesting to see how that handles it
when it suddenly actually does something.
Where to next:
--------------------
After committing the ABI compatible version and MFCing it, I'd
like to proceed in a forward direction in -current. this will
result in some roto-tilling in the routing code.
Firstly: the current code's idea of having a separate tree per
protocol family, all of the same format, and pointed to by the
1 dimensional array is a bit silly. Especially when one considers that
there is code that makes assumptions about every protocol having the
same internal structures there. Some protocols don't WANT that
sort of structure. (for example the whole idea of a netmask is foreign
to appletalk). This needs to be made opaque to the external code.
My suggested first change is to add routing method pointers to the
'domain' structure, along with information pointing the data.
instead of having an array of pointers to uniform structures,
there would be an array pointing to the 'domain' structures
for each protocol address domain (protocol family),
and the methods this reached would be called. The methods would have
an argument that gives FIB number, but the protocol would be free
to ignore it.
When the ABI can be changed it raises the possibilty of the
addition of a fib entry into the "struct route". Currently,
the structure contains the sockaddr of the desination, and the resulting
fib entry. To make this work fully, one could add a fib number
so that given an address and a fib, one can find the third element, the
fib entry.
Interaction with the ARP layer/ LL layer would need to be
revisited as well. Qing Li has been working on this already.
This work was sponsored by Ironport Systems/Cisco
Reviewed by: several including rwatson, bz and mlair (parts each)
Obtained from: Ironport systems/Cisco
to profile outoing packets for a number of mbuf chain
related parameters
e.g. number of mbufs, wasted space.
probably will do with further work later.
Reviewed by: various
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
user-mode lock manager, build a kernel with the NFSLOCKD option and
add '-k' to 'rpc_lockd_flags' in rc.conf.
Highlights include:
* Thread-safe kernel RPC client - many threads can use the same RPC
client handle safely with replies being de-multiplexed at the socket
upcall (typically driven directly by the NIC interrupt) and handed
off to whichever thread matches the reply. For UDP sockets, many RPC
clients can share the same socket. This allows the use of a single
privileged UDP port number to talk to an arbitrary number of remote
hosts.
* Single-threaded kernel RPC server. Adding support for multi-threaded
server would be relatively straightforward and would follow
approximately the Solaris KPI. A single thread should be sufficient
for the NLM since it should rarely block in normal operation.
* Kernel mode NLM server supporting cancel requests and granted
callbacks. I've tested the NLM server reasonably extensively - it
passes both my own tests and the NFS Connectathon locking tests
running on Solaris, Mac OS X and Ubuntu Linux.
* Userland NLM client supported. While the NLM server doesn't have
support for the local NFS client's locking needs, it does have to
field async replies and granted callbacks from remote NLMs that the
local client has contacted. We relay these replies to the userland
rpc.lockd over a local domain RPC socket.
* Robust deadlock detection for the local lock manager. In particular
it will detect deadlocks caused by a lock request that covers more
than one blocking request. As required by the NLM protocol, all
deadlock detection happens synchronously - a user is guaranteed that
if a lock request isn't rejected immediately, the lock will
eventually be granted. The old system allowed for a 'deferred
deadlock' condition where a blocked lock request could wake up and
find that some other deadlock-causing lock owner had beaten them to
the lock.
* Since both local and remote locks are managed by the same kernel
locking code, local and remote processes can safely use file locks
for mutual exclusion. Local processes have no fairness advantage
compared to remote processes when contending to lock a region that
has just been unlocked - the local lock manager enforces a strict
first-come first-served model for both local and remote lockers.
Sponsored by: Isilon Systems
PR: 95247 107555 115524 116679
MFC after: 2 weeks
and t3_push_frames).
- Import latest changes to cxgb_main.c and cxgb_sge.c from toestack p4 branch
- make driver local copy of tcp_subr.c and tcp_usrreq.c and override tcp_usrreqs so
TOE can also functions on versions with unmodified TCP
- add cxgb back to the build
o Disklabels can have between 8 and 20 partitions (inclusive).
o No device special file is created for the raw partition.
o Switch ia64 to use this backend.
o No support for boot code yet.
INCLUDE_CONFIG_FILE. Make a user to look at what config(8) actually does,
and how can one fetch actual configuration file.
Reported by: many
Reviewed by: cognet (mentor)
Approved by: cognet (mentor)
- Introduce per-architecture stack_machdep.c to hold stack_save(9).
- Introduce per-architecture machine/stack.h to capture any common
definitions required between db_trace.c and stack_machdep.c.
- Add new kernel option "options STACK"; we will build in stack(9) if it is
defined, or also if "options DDB" is defined to provide compatibility
with existing users of stack(9).
Add new stack_save_td(9) function, which allows the capture of a stacktrace
of another thread rather than the current thread, which the existing
stack_save(9) was limited to. It requires that the thread be neither
swapped out nor running, which is the responsibility of the consumer to
enforce.
Update stack(9) man page.
Build tested: amd64, arm, i386, ia64, powerpc, sparc64, sun4v
Runtime tested: amd64 (rwatson), arm (cognet), i386 (rwatson)
Currently, Giant is not too much contented so that it is ok to treact it
like any other mutexes.
Please don't forget to update your own custom config kernel files.
Approved by: cognet, marcel (maintainers of arches where option is
not enabled at the moment)
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
commented out until I can re-test them on all our architectures. I
had re@ approval to commit this a long time ago, but that's before we
were this close to the branch.
Approved by: re@
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
Also rename the related functions in a similar way.
There are no functional changes.
For a packet coming in with IPsec tunnel mode, the default is
to only call into the firewall with the "outer" IP header and
payload.
With this option turned on, in addition to the "outer" parts,
the "inner" IP header and payload are passed to the
firewall too when going through ip_input() the second time.
The option was never only related to a gif(4) tunnel within
an IPsec tunnel and thus the name was very misleading.
Discussed at: BSDCan 2007
Best new name suggested by: rwatson
Reviewed by: rwatson
Approved by: re (bmah)
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
NET_NEEDS_GIANT, which will shortly be removed. This is done in a
away that it may be easily reattached to the build before 7.1 if
appropriate locking is added. Specifics:
- Don't install netatm include files
- Disconnect netatm command line management tools
- Don't build libatm
- Don't include ATM parts in rescue or sysinstall
- Don't install sample configuration files and documents
- Don't build kernel support as a module or in NOTES
- Don't build netgraph wrapper nodes for netatm
This removes the last remaining consumer of NET_NEEDS_GIANT.
Reviewed by: harti
Discussed with: bz, bms
Approved by: re (kensmith)
This commit includes only the kernel files, the rest of the files
will follow in a second commit.
Reviewed by: bz
Approved by: re
Supported by: Secure Computing
both 6.x and 7.x. This is based on feedbacks on this thread
http://docs.freebsd.org/cgi/getmsg.cgi?fetch=81818+0+current/freebsd-stable
and my use it on 6.x.
MFC after: 3 days
- Update the warning about UNION filesystem. It is now actively maintained,
although there are still some issues being resolved.
Reviewed by: freebsd-stable@, kris, bmah
Approved by: re (bmah)
This allocator uses a binary buddy system with a twist. First and
foremost, this allocator is required to support the implementation of
superpages. As a side effect, it enables a more robust implementation
of contigmalloc(9). Moreover, this reimplementation of
contigmalloc(9) eliminates the acquisition of Giant by
contigmalloc(..., M_NOWAIT, ...).
The twist is that this allocator tries to reduce the number of TLB
misses incurred by accesses through a direct map to small, UMA-managed
objects and page table pages. Roughly speaking, the physical pages
that are allocated for such purposes are clustered together in the
physical address space. The performance benefits vary. In the most
extreme case, a uniprocessor kernel running on an Opteron, I measured
an 18% reduction in system time during a buildworld.
This allocator does not implement page coloring. The reason is that
superpages have much the same effect. The contiguous physical memory
allocation necessary for a superpage is inherently colored.
Finally, the one caveat is that this allocator does not effectively
support prezeroed pages. I hope this is temporary. On i386, this is
a slight pessimization. However, on amd64, the beneficial effects of
the direct-map optimization outweigh the ill effects. I speculate
that this is true in general of machines with a direct map.
Approved by: re
tunnels, and was not MPSAFE. The code can be easily restored in the
event that someone with an IPX over IP tunnel configuration can work
with me to test patches.
This removes one of five remaining consumers of NET_NEEDS_GIANT.
Approved by: re (kensmith)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
The name trunk is misused as the networking term trunk means carrying multiple
VLANs over a single connection. The IEEE standard for link aggregation (802.3
section 3) does not talk about 'trunk' at all while it is used throughout IEEE
802.1Q in describing vlans.
The lagg(4) driver provides link aggregation, failover and fault tolerance.
Discussed on: current@
Linux SCSI SG passthrough device API. The intention is to allow for both
running of Linux apps that want to talk to /dev/sg* nodes, and to facilitate
porting of apps from Linux to FreeBSD. As such, both native and linuxolator
entry points and definitions are provided.
Caveats:
- This does not support the procfs and sysfs nodes that the Linux SG
driver provides. Some Linux apps may rely on these for operation,
others may only use them for informational purposes.
- More ioctls need to be implemented.
- Linux uses a naming scheme of "sg[a-z]" for devices, while FreeBSD uses a
scheme of "sg[0-9]". Devfs aliasis (symlinks) are automatically created
to link the two together. However, tools like camcontrol only see the
native names.
- Some operations were originally designed to return byte counts or other
data directly as the syscall return value. The linuxolator doesn't appear
to support this well, so this driver just punts for these cases.
Now that the driver is in place, others are welcome to add missing
functionality. Thanks to Roman Divacky for pushing this work along.
When the linux port changes were imported which split the
target command list to be separate from the initiator command
list and the handle format changed to encode a type in the handle
the implications to the function isp_handle_index (which only
the NetBSD/OpenBSD/FreeBSD ports use) were overlooked.
The fault is twofold: first, the index into the DMA maps
in isp_pci is wrong because a target command handle with
the type bit left in place caused a bad index (and panic)
into dma map. Secondly, the assumption of the array
of DMA maps in either PCS or SBUS attachment structures is
that there is a linear mapping between handle index and
DMA map index. This can no longer be true if there are
overlapping index spaces for initiator mode and target
mode commands.
These changes bandaid around the problem by forcing us
to not have simultaneous dual roles and doing the appropriate
masking to make sure things are indexed correctly. A longer
term fix is being devloped.
obtaining and releasing shared and exclusive locks. The algorithms for
manipulating the lock cookie are very similar to that rwlocks. This patch
also adds support for exclusive locks using the same algorithm as mutexes.
A new sx_init_flags() function has been added so that optional flags can be
specified to alter a given locks behavior. The flags include SX_DUPOK,
SX_NOWITNESS, SX_NOPROFILE, and SX_QUITE which are all identical in nature
to the similar flags for mutexes.
Adaptive spinning on select locks may be enabled by enabling the
ADAPTIVE_SX kernel option. Only locks initialized with the SX_ADAPTIVESPIN
flag via sx_init_flags() will adaptively spin.
The common cases for sx_slock(), sx_sunlock(), sx_xlock(), and sx_xunlock()
are now performed inline in non-debug kernels. As a result, <sys/sx.h> now
requires <sys/lock.h> to be included prior to <sys/sx.h>.
The new kernel option SX_NOINLINE can be used to disable the aforementioned
inlining in non-debug kernels.
The size of struct sx has changed, so the kernel ABI is probably greatly
disturbed.
MFC after: 1 month
Submitted by: attilio
Tested by: kris, pjd
imitating an Ethernet device, so vlan(4) and if_bridge(4) can be
attached to it for testing and benchmarking purposes. Its source
can be an introduction to the anatomy of a network interface driver
due to its simplicity as well as to a bunch of comments in it.
arrangement that has no intrinsic internal knowledge of whether devices
it is given are truly multipath devices. As such, this is a simplistic
approach, but still a useful one.
The basic approach is to (at present- this will change soon) use camcontrol
to find likely identical devices and and label the trailing sector of the
first one. This label contains both a full UUID and a name. The name is
what is presented in /dev/multipath, but the UUID is used as a true
distinguishor at g_taste time, thus making sure we don't have chaos
on a shared SAN where everyone names their data multipath as "Fred".
The first of N identical devices (and N *may* be 1!) becomes the active
path until a BIO request is failed with EIO or ENXIO. When this occurs,
the active disk is ripped away and the next in a list is picked to
(retry and) continue with.
During g_taste events new disks that meet the match criteria for existing
multipath geoms get added to the tail end of the list.
Thus, this active/passive setup actually does work for devices which
go away and come back, as do (now) mpt(4) and isp(4) SAN based disks.
There is still a lot to do to improve this- like about 5 of the 12
recommendations I've received about it, but it's been functional enough
for a while that it deserves a broader test base.
Reviewed by: pjd
Sponsored by: IronPort Systems
MFC: 2 months
Make PIM dynamically loadable by using encap_attach_func().
PIM may now be loaded into a GENERIC kernel.
Tested with: ports/net/pimdd && tcpreplay && wireshark
Reviewed by: Pavlin Radoslavov
partitioning class that supports multiple schemes. Current
schemes supported are APM (Apple Partition Map) and GPT.
Change all GEOM_APPLE anf GEOM_GPT options into GEOM_PART_APM
and GEOM_PART_GPT (resp).
The ctlreq interface supports verbs to create and destroy
partitioning schemes on a disk; to add, delete and modify
partitions; and to commit or undo changes made.
NOTES though, as ofw_syscons(4) doesn't properly interface with
syscons(4) regarding loading the font specified with SC_DFLT_FONT,
causing a kernel with both options SC_OFWFB and SC_NO_MODE_CHANGE
to not link.
lookup early. This has some performance implications and should not be
enabled by default, but might help greatly in certain setups. After some
more testing this could be turned into a sysctl.
Tested by: avatar
LOR ids: 17, 24, 32, 46, 191 (conceptual)
MFC after: 6 weeks
work is not just mine, but it is also the works of Peter Lei
and Michael Tuexen. They both are my two key other developers
working on the project.. and they need ata-boy's too:
****
peterlei@cisco.comtuexen@fh-muenster.de
****
I did do a make sysent which updated the
syscall's and sysproto.. I hope that is correct... without
it you don't build since we have new syscalls for SCTP :-0
So go out and look at the NOTES, add
option SCTP (make sure inet and inet6 are present too)
and play with SCTP.
I will see about comitting some test tools I have after I
figure out where I should place them. I also have a
lib (libsctp.a) that adds some of the missing socketapi
functions that I need to put into lib's.. I will talk
to George about this :-)
There may still be some 64 bit issues in here, none of
us have a 64 bit processor to test with yet.. Michael
may have a MAC but thats another beast too..
If you have a mac and want to use SCTP contact Michael
he maintains a web site with a loadable module with
this code :-)
Reviewed by: gnn
Approved by: gnn
unsuspecting users.
- Add a comment in NOTES about experimental status of SCHED_ULE.
- Make warning about experimental status in sched_ule(4) a bit
stronger.
Suggested and reviewed by: dougb
Discussed on: developers
MFC after: 3 days
other problems while labels were first being added to various kernel
objects. They have outlived their usefulness.
MFC after: 1 month
Suggested by: Christopher dot Vance at SPARTA dot com
Obtained from: TrustedBSD Project
in older versions of FreeBSD. This option is pointless as it is needed in just
about every interesting usage of forward that I have ever seen. It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x It doesn't make
the system any safer and just wastes huge amounts of develper time
when the system doesn't behave as expected when code is moved from
4.x to 6.x or 7.x
Reviewed by: glebius
MFC after: 1 week
and pc98 MD files. Remove nodevice and nooption lines specific
to sio(4) from ia64, powerpc and sparc64 NOTES. There were no
such lines for arm yet.
sio(4) is usable on less than half the platforms, not counting
a future mips platform. Its presence in MI files is therefore
increasingly becoming a burden.
in 1999, and there are changes to the sysctl names compared to PR,
according to that discussion. The description is in sys/conf/NOTES.
Lines in the GENERIC files are added in commented-out form.
I'll attach the test script I've used to PR.
PR: kern/14584
Submitted by: babkin
I picked it up again. The scheduler is forked from ULE, but the
algorithm to detect an interactive process is almost completely
different with ULE, it comes from Linux paper "Understanding the
Linux 2.6.8.1 CPU Scheduler", although I still use same word
"score" as a priority boost in ULE scheduler.
Briefly, the scheduler has following characteristic:
1. Timesharing process's nice value is seriously respected,
timeslice and interaction detecting algorithm are based
on nice value.
2. per-cpu scheduling queue and load balancing.
3. O(1) scheduling.
4. Some cpu affinity code in wakeup path.
5. Support POSIX SCHED_FIFO and SCHED_RR.
Unlike scheduler 4BSD and ULE which using fuzzy RQ_PPQ, the scheduler
uses 256 priority queues. Unlike ULE which using pull and push, the
scheduelr uses pull method, the main reason is to let relative idle
cpu do the work, but current the whole scheduler is protected by the
big sched_lock, so the benefit is not visible, it really can be worse
than nothing because all other cpu are locked out when we are doing
balancing work, which the 4BSD scheduelr does not have this problem.
The scheduler does not support hyperthreading very well, in fact,
the scheduler does not make the difference between physical CPU and
logical CPU, this should be improved in feature. The scheduler has
priority inversion problem on MP machine, it is not good for
realtime scheduling, it can cause realtime process starving.
As a result, it seems the MySQL super-smack runs better on my
Pentium-D machine when using libthr, despite on UP or SMP kernel.
the linux module, since it is not cross-platform
- move linprocfs from "files" and "options" to architecture specific files,
since it only makes sense to build this for those architectures, where we
also have a linuxolator
- disable the build of the linuxolator on our tier-2 architecture "Alpha":
* we don't have a linux_base port which supports Alpha and at the
same time is not outdated/obsoleted upstream/in a good condition/
currently working
* the upcomming new default linux base port is based upon Fedora
Core 3 (security support via http://www.fedoralegacy.org), which
isn't available for Alpha (like the current default linux base
port which is based upon Red Hat 8)
* nobody answered my request for testing it ~1 month ago on
current@ and alpha@ (it doesn't surprises me, see above)
* a SoC student wouldn't have to waste time on something which
nobody is willing to test
This does not remove the alpha specific MD files of the linuxolator yet.
Discussed on: arch (mostly silence)
Spiritual support by: scottl
o Properly use rman(9) to manage resources. This eliminates the
need to puc-specific hacks to rman. It also allows devinfo(8)
to be used to find out the specific assignment of resources to
serial/parallel ports.
o Compress the PCI device "database" by optimizing for the common
case and to use a procedural interface to handle the exceptions.
The procedural interface also generalizes the need to setup the
hardware (program chipsets, program clock frequencies).
o Eliminate the need for PUC_FASTINTR. Serdev devices are fast by
default and non-serdev devices are handled by the bus.
o Use the serdev I/F to collect interrupt status and to handle
interrupts across ports in priority order.
o Sync the PCI device configuration to include devices found in
NetBSD and not yet merged to FreeBSD.
o Add support for Quatech 2, 4 and 8 port UARTs.
o Add support for a couple dozen Timedia serial cards as found
in Linux.
o Add the scc(4) manpage to the build.
o Update the uart(4) manpage to account for scc(4).
o Update the uart(4) module build to include support for scc(4).
enabled by default in NETSMB and smbfs.ko.
With the most of modern SMB providers requiring encryption by
default, there is little sense left in keeping the crypto part
of NETSMB optional at the build time.
This will also return smbfs.ko to its former properties users
are rather accustomed to.
Discussed with: freebsd-stable, re (scottl)
Not objected by: bp, tjr (silence)
MFC after: 5 days
in order to support the on-board LANCE in Ultra 1 and to the MI NOTES as
it should work just fine with the AMD PCnet family of chips on all archs
but is not yet meant to replace lnc(4). If a kernel includes all of le(4),
lnc(4) and pcn(4) precedence is given to lnc(4)/pcn(4) for now.
It detects both: buffer underflows and buffer overflows bugs at runtime
(on free(9) and realloc(9)) and prints backtraces from where memory was
allocated and from where it was freed.
Tested by: kris
specially crafted module. There are several handrolled sollutions to this
problem in the tree already which will be replaced with this. They include
iwi(4), ipw(4), ispfw(4) and digi(4).
No objection from: arch
MFC after: 2 weeks
X-MFC after: some drivers have been converted
I couldn't find the ID for the EG1064 anywhere in our sources
so I removed the reference for now.
Pointed out by: Robert Huff <roberthuffi at rcn dot com> [1]
Reviewed by: simon
to COMPAT_43TTY.
Add COMPAT_43TTY to NOTES and */conf/GENERIC
Compile tty_compat.c only under the new option.
Spit out
#warning "Old BSD tty API used, please upgrade."
if ioctl_compat.h gets #included from userland.
- provide an interface (macros) to the page coloring part of the VM system,
this allows to try different coloring algorithms without the need to
touch every file [1]
- make the page queue tuning values readable: sysctl vm.stats.pagequeue
- autotuning of the page coloring values based upon the cache size instead
of options in the kernel config (disabling of the page coloring as a
kernel option is still possible)
MD changes:
- detection of the cache size: only IA32 and AMD64 (untested) contains
cache size detection code, every other arch just comes with a dummy
function (this results in the use of default values like it was the
case without the autotuning of the page coloring)
- print some more info on Intel CPU's (like we do on AMD and Transmeta
CPU's)
Note to AMD owners (IA32 and AMD64): please run "sysctl vm.stats.pagequeue"
and report if the cache* values are zero (= bug in the cache detection code)
or not.
Based upon work by: Chad David <davidc@acns.ab.ca> [1]
Reviewed by: alc, arch (in 2004)
Discussed with: alc, Chad David, arch (in 2004)
interface polling, compiles on 64-bit platforms, and compiles on NetBSD,
OpenBSD, BSD/OS, and Linux. Woo! Thanks to David Boggs for providing this
driver.
Altq, sppp, netgraph, and bpf are required for this driver to operate.
Userland tools and man pages will be committed next.
Submitted by: David Boggs
replacement and has additional features which make it superior.
Discussed on: -arch
Reviewed by: thompsa
X-MFC-after: never (RELENG_6 as transition period)
exist on other architectures yet.
- While I'm here, fix the formatting of the options line. The keyword
"options" should be followed by a space and then a tab, not 2 tabs.
FreeBSD based on aue(4) it was picked by OpenBSD, then from OpenBSD ported
to NetBSD and finally NetBSD version merged with original one goes into
FreeBSD.
Obtained from: http://www.gank.org/freebsd/cdce/
NetBSD
OpenBSD
This is mentioned in the Handbook but it is not as obvious to new
users why bpf is needed compared to the other largely self-explanatory
items in GENERIC.
PR: conf/40855
MFC after: 1 week
- "options" is followed by the characters \040\011, not \011\011.
Correct both my own sins and those of others.
- Comment blocks start and end with an empty line ^#$.
- Remove non-standard comments added in my last commit.
Requested by: njl
Correctness confirmed by: bde
with the kernel compile time option:
options IPFIREWALL_FORWARD_EXTENDED
This option has to be specified in addition to IPFIRWALL_FORWARD.
With this option even packets targeted for an IP address local
to the host can be redirected. All restrictions to ensure proper
behaviour for locally generated packets are turned off. Firewall
rules have to be carefully crafted to make sure that things like
PMTU discovery do not break.
Document the two kernel options.
PR: kern/71910
PR: kern/73129
MFC after: 1 week
This driver implements "unaddressed listen only mode", which is what
printers and plotters commonly do on GP-IB busses.
This means that you can capture print/plot like output from your
instruments by configuring them as necessary (good luck!) and
cat -u /dev/gpib0l > /tmp/somefile
Since there is no way to know when no more output is comming you
will have to ctrl-C the cat process when it is done (that is why
the -u is important).
designed to help detect tamper-after-free scenarios, a problem more
and more common and likely with multithreaded kernels where race
conditions are more prevalent.
Currently MemGuard can only take over malloc()/realloc()/free() for
particular (a) malloc type(s) and the code brought in with this
change manually instruments it to take over M_SUBPROC allocations
as an example. If you are planning to use it, for now you must:
1) Put "options DEBUG_MEMGUARD" in your kernel config.
2) Edit src/sys/kern/kern_malloc.c manually, look for
"XXX CHANGEME" and replace the M_SUBPROC comparison with
the appropriate malloc type (this might require additional
but small/simple code modification if, say, the malloc type
is declared out of scope).
3) Build and install your kernel. Tune vm.memguard_divisor
boot-time tunable which is used to scale how much of kmem_map
you want to allott for MemGuard's use. The default is 10,
so kmem_size/10.
ToDo:
1) Bring in a memguard(9) man page.
2) Better instrumentation (e.g., boot-time) of MemGuard taking
over malloc types.
3) Teach UMA about MemGuard to allow MemGuard to override zone
allocations too.
4) Improve MemGuard if necessary.
This work is partly based on some old patches from Ian Dowse.
an inordinate amount of synchronous console output that is fairly
undesirable on slower serial console. It's easily hit by accident
when frobbing other sysctls late at night.
on UltraSPARC workstations. The driver is based on OpenBSD's SBus
cs4231 driver and heavily modified to incorporate into sound(4)
infrastructure. Due to the lack of APCDMA documentation, the DMA
code of SBus cs4231 came from OpenBSD's driver.
The driver runs without Giant lock and supports both SBus and EBus
based CS4231 audio controller. Special thanks to marius for providing
feedbacks during the driver writing. His feedback made it possible
to write hiccup free playback code under high system loads.
Approved by: jake (mentor)
Reviewed by: marius (initial version)
Tested by: marius, kwm, Julian C. Dunn(jdunn AT opentrend DOT net)
Users should move to the new geom_vinum implementation instead.
The refcount logic which is being added to devices to enable safe module
unloading and the buf/vm work also in progress would require a major rework
of the (old)-vinum code to comply with the new semantics.
The actual source files will not be removed until I have coordinated with
the geomvinum people if they need any bits repo-copied etc.
FULL_PREEMPTION is defined. Add a runtime warning to ULE if PREEMPTION is
enabled (code inspired by the PREEMPTION warning in kern_switch.c). This
is a possible MT5 candidate.
remaining consumers to have the count passed as an option. This is
i4b, pc98/wdc, and coda.
Bump configvers.h from 500013 to 600000.
Remove heuristics that tried to parse "device ed5" as 5 units of the ed
device. This broke things like the snd_emu10k1 device, which required
quotes to make it parse right. The no-longer-needed quotes have been
removed from NOTES, GENERIC etc. eg, I've removed the quotes from:
device snd_maestro
device "snd_maestro3"
device snd_mss
I believe everything will still compile and work after this.
compile option. All FreeBSD packet filters now use the PFIL_HOOKS API and
thus it becomes a standard part of the network stack.
If no hooks are connected the entire packet filter hooks section and related
activities are jumped over. This removes any performance impact if no hooks
are active.
Both OpenBSD and DragonFlyBSD have integrated PFIL_HOOKS permanently as well.
have already done this, so I have styled the patch on their work:
1) introduce a ip_newid() static inline function that checks
the sysctl and then decides if it should return a sequential
or random IP ID.
2) named the sysctl net.inet.ip.random_id
3) IPv6 flow IDs and fragment IDs are now always random.
Flow IDs and frag IDs are significantly less common in the
IPv6 world (ie. rarely generated per-packet), so there should
be smaller performance concerns.
The sysctl defaults to 0 (sequential IP IDs).
Reviewed by: andre, silby, mlaier, ume
Based on: NetBSD
MFC after: 2 months
their own directory and module, leaving the MD parts in the MD
area (the MD parts _are_ part of the modules). /dev/mem and /dev/io
are now loadable modules, thus taking us one step further towards
a kernel created entirely out of modules. Of course, there is nothing
preventing the kernel from having these statically compiled.
an adaptive fashion when adaptive mutexes are enabled. The theory
behind non-adaptive Giant is that Giant will be held for long periods
of time, and therefore spinning waiting on it is wasteful. However,
in MySQL benchmarks which are relatively Giant-free, running Giant
adaptive makes an observable difference on SMP (5% transaction rate
improvement). As such, make adaptive behavior on Giant an option so
it can be more widely benchmarked.
NO_ADAPTIVE_MUTEXES. This option has been enabled by default on amd64 for
quite some time, and has been extensively tested on i386 and sparc64. It
shows measurable performance gains in many circumstances, and few negative
effects. It would be nice in t he future if adaptive mutexes actually went
to sleep after a certain amount of spinning, but that will require quite a
bit more testing.
- `sound'
The generic sound driver, always required.
- `snd_*'
Device-dependent drivers, named after the sound module names.
Configure accordingly to your hardware.
In addition, rename the `snd_pcm' module to `sound' in order to sync
with the driver names.
Suggested by: cg
o Rename WITNESS_DDB to WITNESS_KDB. In the new world order KDB is the
acronym to use for debugging related code. The DDB option is used
to enable the DDB debugger backend only.
o Likewise, rename DDB_TRACE to KDB_TRACE, rename DDB_UNATTENDED to
KDB_UNATTENDED and rename SC_HISTORY_DDBKEY to SC_HISTORY_KDBKEY.
o Remove DDB_NOKLDSYM. The new DDB backend supports pre-linker symbol
lookups as well as KLD symbol lookups at the same time.
o Remove GDB_REMOTE_CHAT. The GDB protocol hacks to allow this are
FreeBSD specific. At the same time, the GDB protocol has packets
for console output.
bootp -> BOOTP
bootp.nfsroot -> BOOTP_NFSROOT
bootp.nfsv3 -> BOOTP_NFSV3
bootp.compat -> BOOTP_COMPAT
bootp.wired_to -> BOOTP_WIRED_TO
- i.e. back out the previous commit. It's already possible to
pxeboot(8) with a GENERIC kernel.
Pointed out by: dwmalone
BOOTP -> bootp
BOOTP_NFSROOT -> bootp.nfsroot
BOOTP_NFSV3 -> bootp.nfsv3
BOOTP_COMPAT -> bootp.compat
BOOTP_WIRED_TO -> bootp.wired_to
This lets you PXE boot with a GENERIC kernel by putting this sort of thing
in loader.conf:
bootp="YES"
bootp.nfsroot="YES"
bootp.nfsv3="YES"
bootp.wired_to="bge1"
or even setting the variables manually from the OK prompt.
FAT32 filesystems to be mounted, subject to some fairly serious limitations.
This works by extending the internal pseudo-inode-numbers generated from
the file's starting cluster number to 64-bits, then creating a table
mapping these into arbitrary 32-bit inode numbers, which can fit in
struct dirent's d_fileno and struct vattr's va_fileid fields. The mappings
do not persist across unmounts or reboots, so it's not possible to export
these filesystems through NFS. The mapping table may grow to be rather
large, and may grow large enough to exhaust kernel memory on filesystems
with millions of files.
Don't enable this option unless you understand the consequences.
than as one-off hacks in various other parts of the kernel:
- Add a function maybe_preempt() that is called from sched_add() to
determine if a thread about to be added to a run queue should be
preempted to directly. If it is not safe to preempt or if the new
thread does not have a high enough priority, then the function returns
false and sched_add() adds the thread to the run queue. If the thread
should be preempted to but the current thread is in a nested critical
section, then the flag TDF_OWEPREEMPT is set and the thread is added
to the run queue. Otherwise, mi_switch() is called immediately and the
thread is never added to the run queue since it is switch to directly.
When exiting an outermost critical section, if TDF_OWEPREEMPT is set,
then clear it and call mi_switch() to perform the deferred preemption.
- Remove explicit preemption from ithread_schedule() as calling
setrunqueue() now does all the correct work. This also removes the
do_switch argument from ithread_schedule().
- Do not use the manual preemption code in mtx_unlock if the architecture
supports native preemption.
- Don't call mi_switch() in a loop during shutdown to give ithreads a
chance to run if the architecture supports native preemption since
the ithreads will just preempt DELAY().
- Don't call mi_switch() from the page zeroing idle thread for
architectures that support native preemption as it is unnecessary.
- Native preemption is enabled on the same archs that supported ithread
preemption, namely alpha, i386, and amd64.
This change should largely be a NOP for the default case as committed
except that we will do fewer context switches in a few cases and will
avoid the run queues completely when preempting.
Approved by: scottl (with his re@ hat)
