by zero of the second argument 'from'.
- Prefer u_int32_t over unsigned int to make its intention more clearer.
- Move the function to a header file and make it a static inline function.
Pointed out by: Andrew Reilly (areilly at bigpond dot net dot au)[1]
MFC after: 3 days
On top of that, LLVM+Clang mis-compiles this code because of its register
allocator bug.
Analyzed by: Andrew Reilly (areilly at bigpond dot net dot au)
Reviewed by: ariff, rdivacky
MFC after: 3 days
volumes were incorrectly calculated.
I've tested this with one of my es1370 cards and I can confirm that it
works.
PR: 98167
Submitted by: Joseph Terner <jtsn@gmx.de>
Approved by: kib
loopback.
- Change the meaning of "mix" OSS control. Now it controls loopback level,
according to comments in soundcard.h.
- Allow AD1981HD codecs to use playback mixer. Now driver should be able to
really use it.
- Fix bug in shared muters operation.
as different nearby ones, and was grabbed by MIXER_xxx() handler.
While there, replace '(cmd & MIXER_xxx(0)) == MIXER_xxx(0)' expressions
with more correct '(cmd & ~0xff) == MIXER_READ(0)'. Use of bit operations
to compare numeric fields doesn't looks sane.
MFC after: 1 month
now due to unidentified synchonization problem. For 7.1 soundcards 5.1
support handled correctly via software upmix done by sound(4).
Stereo stream is no more duplicated to all ports. If you loose sound, check
you are using right connectors. Front speakers connector is usually green,
center/LFE - orange, rear - black, side - gray.
This replaces d_mmap() with the d_mmap2() implementation and also
changes the type of offset to vm_ooffset_t.
Purge d_mmap2().
All driver modules will need to be rebuilt since D_VERSION is also
bumped.
Reviewed by: jhb@
MFC after: Not in this lifetime...
Fix some wrong usages.
Note: this does not affect generated binaries as this argument is not used.
PR: 137213
Submitted by: Eygene Ryabinkin (initial version)
MFC after: 1 month
- fix issues regarding the mixer, where the interface number was not set in
time.
- fix wrong use of resolution parameter.
Submitted by: Hans Petter Selasky
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
MFC after: 3 days
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
This dramatically pushing 99.9% interpolations and quantizations
error _below_ -180dB on 32bit dynamic range, resulting extremely
high quality conversion.
- Use BSPLINE interpolator for filter oversampling factor greater or
equal than 64 (log2 6).
Approved by: re (kib)
This cause dramatic effect in overall precision and conversion quality
by pushing down most aliasing artifacts around -180 dB.
Spectrogram analysis/comparison:
http://people.freebsd.org/~ariff/z_comparison/z_28vs30/
- Guard against possible 64bit overflow during accumulation process by
slightly normalize and saturate sample and coefficient multiplication,
possible during extreme 32bit downsampling (eg. 380KHz -> 8KHz) with
custom preset that require more than ~7000 taps filter (which is
overkill).
- Add knobs through FEEDER_RATE_PRESETS to set dynamic range of filter
coefficients/accumulator and prefered polynomial interpolator:
COEFFICIENT_BIT:X
(where 1 <= X <= 30, default: 30)
ACCUMULATOR_BIT:X
(where 32 <= X <=64, default: 58)
INTERPOLATOR:I
(where I = ZOH, LINEAR, QUADRATIC, HERMITE, BSPLINE,
OPT32X, OPT16X, OPT8X, OPT4X, OPT2X)
Approved by: re (kib)
Note that this does not actually enable full-range i/o requests for
64 architectures, and is done now to update KBI only.
Tested by: pho
Reviewed by: jhb, bde (as part of the review of the bigger patch)
- honor parent DMA tag limitations, as man page requires,
- allow data buffer to be allocated within full 64bit address range, when
support is announced by hardware,
- add quirk, disabling 64bit addresses for broken chips, use it for MCP78.
FEEDER_RATE_PRESET "OVERSAMPLING_FACTOR:X .. .." where
X = log2(oversampling factor).
- Lower down default filter oversampling factor from 128
(log2 = 7) to 32 (log2 = 5), saving worth of 80 Kb.
The use of better polynomial interpolator will raise
its conversion quality/accuracy to match (or slightly
better) with previous settings.
- Bump driver version.
coefficients quality:
- Linear interpolator for oversampling factor larger and equal
than 4096 (log2 = 12).
- Quadratic interpolator for oversampling factor larger and equal
than 256 (log2 = 8).
Default oversampling factor (128 ~ log2 = 7) will use OPT32X, which
provides better accuracy.
For a slightly thorough explaination, please refer to
[1] http://people.freebsd.org/~ariff/SOUND_4.TXT.html .
Summary of changes includes:
1 Volume Per-Channel (vpc). Provides private / standalone volume control
unique per-stream pcm channel without touching master volume / pcm.
Applications can directly use SNDCTL_DSP_[GET|SET][PLAY|REC]VOL, or for
backwards compatibility, SOUND_MIXER_PCM through the opened dsp device
instead of /dev/mixer. Special "bypass" mode is enabled through
/dev/mixer which will automatically detect if the adjustment is made
through /dev/mixer and forward its request to this private volume
controller. Changes to this volume object will not interfere with
other channels.
Requirements:
- SNDCTL_DSP_[GET|SET][PLAY|REC]_VOL are newer ioctls (OSSv4) which
require specific application modifications (preferred).
- No modifications required for using bypass mode, so applications
like mplayer or xmms should work out of the box.
Kernel hints:
- hint.pcm.%d.vpc (0 = disable vpc).
Kernel sysctls:
- hw.snd.vpc_mixer_bypass (default: 1). Enable or disable /dev/mixer
bypass mode.
- hw.snd.vpc_autoreset (default: 1). By default, closing/opening
/dev/dsp will reset the volume back to 0 db gain/attenuation.
Setting this to 0 will preserve its settings across device
closing/opening.
- hw.snd.vpc_reset (default: 0). Panic/reset button to reset all
volume settings back to 0 db.
- hw.snd.vpc_0db (default: 45). 0 db relative to linear mixer value.
2 High quality fixed-point Bandlimited SINC sampling rate converter,
based on Julius O'Smith's Digital Audio Resampling -
http://ccrma.stanford.edu/~jos/resample/. It includes a filter design
script written in awk (the clumsiest joke I've ever written)
- 100% 32bit fixed-point, 64bit accumulator.
- Possibly among the fastest (if not fastest) of its kind.
- Resampling quality is tunable, either runtime or during kernel
compilation (FEEDER_RATE_PRESETS).
- Quality can be further customized during kernel compilation by
defining FEEDER_RATE_PRESETS in /etc/make.conf.
Kernel sysctls:
- hw.snd.feeder_rate_quality.
0 - Zero-order Hold (ZOH). Fastest, bad quality.
1 - Linear Interpolation (LINEAR). Slightly slower than ZOH,
better quality but still does not eliminate aliasing.
2 - (and above) - Sinc Interpolation(SINC). Best quality. SINC
quality always start from 2 and above.
Rough quality comparisons:
- http://people.freebsd.org/~ariff/z_comparison/
3 Bit-perfect mode. Bypasses all feeder/dsp effects. Pure sound will be
directly fed into the hardware.
4 Parametric (compile time) Software Equalizer (Bass/Treble mixer). Can
be customized by defining FEEDER_EQ_PRESETS in /etc/make.conf.
5 Transparent/Adaptive Virtual Channel. Now you don't have to disable
vchans in order to make digital format pass through. It also makes
vchans more dynamic by choosing a better format/rate among all the
concurrent streams, which means that dev.pcm.X.play.vchanformat/rate
becomes sort of optional.
6 Exclusive Stream, with special open() mode O_EXCL. This will "mute"
other concurrent vchan streams and only allow a single channel with
O_EXCL set to keep producing sound.
Other Changes:
* most feeder_* stuffs are compilable in userland. Let's not
speculate whether we should go all out for it (save that for
FreeBSD 16.0-RELEASE).
* kobj signature fixups, thanks to Andriy Gapon <avg@freebsd.org>
* pull out channel mixing logic out of vchan.c and create its own
feeder_mixer for world justice.
* various refactoring here and there, for good or bad.
* activation of few more OSSv4 ioctls() (see [1] above).
* opt_snd.h for possible compile time configuration:
(mostly for debugging purposes, don't try these at home)
SND_DEBUG
SND_DIAGNOSTIC
SND_FEEDER_MULTIFORMAT
SND_FEEDER_FULL_MULTIFORMAT
SND_FEEDER_RATE_HP
SND_PCM_64
SND_OLDSTEREO
Manual page updates are on the way.
Tested by: joel, Olivier SMEDTS <olivier at gid0 d org>, too many
unsung / unnamed heroes.
mic inputs. I have no idea what for it was made that time, but now I have
several reports that it should be removed to make microphones work. If
this quirk is still required for some systems then they should be identified
and specified explicitly.
- make usb2_power_mask_t 16-bit
- remove "usb2_config_sub" structure from "usb2_config". To compensate for this
"usb2_config" has a new field called "usb_mode" which select for which mode
the current xfer entry is active. Options are: a) Device mode only b) Host
mode only (default-by-zero) c) Both modes. This change was scripted using
the following sed script: "s/\.mh\././g".
- the standard packet size table in "usb_transfer.c" is now a function, hence
the code for the function uses less memory than the table itself.
Submitted by: Hans Petter Selasky
only for mic-type inputs. This gives better chances to use it.
Change default configuration for some AD1986A codec based ASUS boards,
use it also for ASUS P5PL2 board. This makes front mic preamplifier working.
Tested by: Vadim Frolov <frolov@frolov.ck.ua>
implement CD input in hardware, while unconditional showing it confuse users.
Also it was made in the way that sometimes improper with present driver.
Add patch for ALC268 based Acer TM5320 to make headphones jack sensing work.
Default configuration defines two separate playback associations, which
current driver unable to trace properly due to order they are defined and
limited codec uniformity.
Submitted by: G. Mirov <g.mirov AT gmail.com>
the devfs clone handler to open the (invisible) devices on the fly.
The /dev entries are layed out as follows,
/dev/usbctl = master device
/dev/usb/0.1.0.5 = usb device, (<bus>.<dev>.<iface>.<endpoint>)
/dev/ugen0.1 -> usb/0.1.0.0 = ugen link to ctrl endpoint
This also removes the custom permissions model from USB. Bump
__FreeBSD_version to 800066.
Submitted by: rink (earlier version)
Disable MSI for nVidia MCP51 controller. Enabling MSI there leads to
unexpected errors and timeouts, that should not happen even if interrupts
are not working completely.
use patches so far:
+ Envy24:
- fix: broken init data for M Audio Delta DiO 2496
- add: support for M Audio Delta 44
- add: support for M Audio Delta 1010LT
Tested by: Dominique Goncalves, dominique.goncalves at gmail.com
- add: support for Terratec EWX 2496
Tested by: Stefan Sperling, stsp at stsp.name
- add: support for M Audio Delta 66
Tested by: Richard Bown, richard.bown at blueyonder.co.uk
- add: support for M Audio Delta 1010
Tested by: Andrew Reilly, areilly at bigpond.net.au
+ Envy24HT:
- add: support for Terrasoniq TS22PCI
- fix: M-Audio Revolution 5.1 sound volume is very low
Reported by: Oliver Hartmann, ohartman at zedat.fu-berlin.de
Andrey Slusar, anrays at gmail.com
Tested by: Andrey Slusar, anrays at gmail.com
Rusu Silviu, arol.the at gmail.com
- fix: M-Audio Revolution 7.1 sound is distorted and very quiet
Reported by: Olev Hannula, hannula at gmail.com
Tested by: Olev Hannula, hannula at gmail.com
Stanislav Belansky, stanislav at icmail.ru
- fix: Terratec PHASE 22 codec is power-off due to wrong init data
Reported by: Philipp Ost, pj at smo.de
Tested by: Philipp Ost, pj at smo.de
+ SpicDS:
- fix: AK4381 produce hiss sound on 192kHz sample rate
- fix: stupid bug with volume control for AK4396
Submitted by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
solving a possible panic when snd_ai2s is loaded at boot time. Also change
the device setup to indicate to the pcm layer that the device is MPSAFE.
Submitted by: Marco Trillo
Suggestions by: Ariff Abdullah
module. These files cause manual interaction when building
ports/audio/aureal-kmod which provides a usable i386-only driver (it requires
linking against some linux object files distributed by vendor which bankrupted
back in 2000).
MFC after: 1 week
Disable some unneeded pathes in overcomplicated input mixer to help parser
to handle the rest better. This gives mic input boost control in some
configurations and just more predictable operation in others.
nodes capabilities. Add "Analog"/"Digital" marks to the pcm device names.
I hope it will help new users easier accept concept of several PCM devices
and understand exact purposes of that devices.
that includes significant features and SMP safety.
This commit includes a more or less complete rewrite of the *BSD USB
stack, including Host Controller and Device Controller drivers and
updating all existing USB drivers to use the new USB API:
1) A brief feature list:
- A new and mutex enabled USB API.
- Many USB drivers are now running Giant free.
- Linux USB kernel compatibility layer.
- New UGEN backend and libusb library, finally solves the "driver
unloading" problem. The new BSD licensed libusb20 library is fully
compatible with libusb-0.1.12 from sourceforge.
- New "usbconfig" utility, for easy configuration of USB.
- Full support for Split transactions, which means you can use your
full speed USB audio device on a high speed USB HUB.
- Full support for HS ISOC transactions, which makes writing drivers
for various HS webcams possible, for example.
- Full support for USB on embedded platforms, mostly cache flushing
and buffer invalidating stuff.
- Safer parsing of USB descriptors.
- Autodetect of annoying USB install disks.
- Support for USB device side mode, also called USB gadget mode,
using the same API like the USB host side. In other words the new
USB stack is symmetric with regard to host and device side.
- Support for USB transfers like I/O vectors, means more throughput
and less interrupts.
- ... see the FreeBSD quarterly status reports under "USB project"
2) To enable the driver in the default kernel build:
2.a) Remove all existing USB device options from your kernel config
file.
2.b) Add the following USB device options to your kernel configuration
file:
# USB core support
device usb2_core
# USB controller support
device usb2_controller
device usb2_controller_ehci
device usb2_controller_ohci
device usb2_controller_uhci
# USB mass storage support
device usb2_storage
device usb2_storage_mass
# USB ethernet support, requires miibus
device usb2_ethernet
device usb2_ethernet_aue
device usb2_ethernet_axe
device usb2_ethernet_cdce
device usb2_ethernet_cue
device usb2_ethernet_kue
device usb2_ethernet_rue
device usb2_ethernet_dav
# USB wireless LAN support
device usb2_wlan
device usb2_wlan_rum
device usb2_wlan_ral
device usb2_wlan_zyd
# USB serial device support
device usb2_serial
device usb2_serial_ark
device usb2_serial_bsa
device usb2_serial_bser
device usb2_serial_chcom
device usb2_serial_cycom
device usb2_serial_foma
device usb2_serial_ftdi
device usb2_serial_gensa
device usb2_serial_ipaq
device usb2_serial_lpt
device usb2_serial_mct
device usb2_serial_modem
device usb2_serial_moscom
device usb2_serial_plcom
device usb2_serial_visor
device usb2_serial_vscom
# USB bluetooth support
device usb2_bluetooth
device usb2_bluetooth_ng
# USB input device support
device usb2_input
device usb2_input_hid
device usb2_input_kbd
device usb2_input_ms
# USB sound and MIDI device support
device usb2_sound
2) To enable the driver at runtime:
2.a) Unload all existing USB modules. If USB is compiled into the
kernel then you might have to build a new kernel.
2.b) Load the "usb2_xxx.ko" modules under /boot/kernel having the same
base name like the kernel device option.
Submitted by: Hans Petter Selasky hselasky at c2i dot net
Reviewed by: imp, alfred
with several points unappropriate for the present parser. This patch
disables input-to-output analog monitoring but instead fixes recording.
Tested by Tobias Grosser on ThinkPad T61p.
After I removed all the unit2minor()/minor2unit() calls from the kernel
yesterday, I realised calling minor() everywhere is quite confusing.
Character devices now only have the ability to store a unit number, not
a minor number. Remove the confusion by using dev2unit() everywhere.
This commit could also be considered as a bug fix. A lot of drivers call
minor(), while they should actually be calling dev2unit(). In -CURRENT
this isn't a problem, but it turns out we never had any problem reports
related to that issue in the past. I suspect not many people connect
more than 256 pieces of the same hardware.
Reviewed by: kib
When I changed kern_conf.c three months ago I made device unit numbers
equal to (unneeded) device minor numbers. We used to require
bitshifting, because there were eight bits in the middle that were
reserved for a device major number. Not very long after I turned
dev2unit(), minor(), unit2minor() and minor2unit() into macro's.
The unit2minor() and minor2unit() macro's were no-ops.
We'd better not remove these four macro's from the kernel, because there
is a lot of (external) code that may still depend on them. For now it's
harmless to remove all invocations of unit2minor() and minor2unit().
Reviewed by: kib
Left only parts surely required for basic troubleshooting and configuration
purposes. There is still very long output, but further shrinking makes it
less informative.
Original debugging can be enabled with hw.snd.verbose=4.
Because of using more clear and same time more functional codec parser
new driver is able to handle more codecs, use them better then before and
without most of previous quirks. All of tested codecs itself manage playback,
record, input mixing and monitoring quite fine. In all of investigated
trouble cases problem was found or in nonstandard codec usage or incorrect
codec configuration made by BIOS. Most of that cases could be fixed using
device hints, some of which are already included to the driver.
New driver supports multiple codecs per HDA bus, multiple audio function
groups per codec and multiple logical sound devices per audio function group.
So don't worry when you get several PCM devices instead of one, it is normal.
It is usual situation with powerful codecs to provide, for example, 3 PCM
devices: one for 7.1 playback and main recording, one for headset and one
for digital SPDIF I/O.
New driver implements Universal Audio Architecture (UAA) much better then
previous one. Most information about recommended codec usage now taken from
the codec configuration registers initialized by BIOS. User may alter that
configuration using device hints to reconfigure logical audio devices to
his needs in a very broad range up to the limits of the codec functionality.
New driver supports digital PCM playback and AC3 pass-through. I am not sure
about completeness of this implementation, but I have several success stories
including my own. Vchans subsystem does not support AC3 pass-through so it
had to be disabled for that devices at this moment.
New driver is ready for multichannel playback, but until our OSS is unable
to use this it will just duplicate same stereo stream into all channel
pairs.
New driver supports suspend/resume. I am unable to really test this part
myself, but I have got several success stories.
Driver has very informative verbose boot messages. So if you have any
questions or problems - enable and read them first.
Discussed on: freebsd-multimedia@
Tested by: many
The PCM's sound.h file only seems to include <sys/tty.h>, because
channel_if seems to require selinfo. Just replace it with
<sys/selinfo.h>.
There's no real problem with including <sys/tty.h> here, even with
MPSAFE TTY, but <sys/tty.h> is something that should be used by the TTY
layer, its driver and code that integrated it with the process tree.
calling destroy_dev() with sleepable malloc(9). The entire opetation
is being serialized through pcm cv from top down, so dropping mutex is
rather safe.
Reported by: delphij
deserves its own internet memes). The trick is to force all available,
unused pins (that being advertised as "speaker") to behave as microphone
pins instead.
Reported / Tested by: Dmitry Kutsenko <kutsenko.truebsd.org>
MFC after: 3 days
- Fix speaker issues with Dell Vostro 1500 (GPIO0)
Tested by: John Wright <jwright.gmail.com>
- Apply ridiculous quirk on Asus A8X series (A8JC, A8M, A8xx, etc). These
different laptop series share simmilar pci id, hardware codecs, etc.
but works differently. A slight difference in connection type for
widget #26 is used to differentiate it.
Tested by: eric baumbach <embaumbach.gmail.com>
- Apply GPIO0 quirk for ASUS G2K laptop
- Sort ASUS ids accordingly.
Submitted by: jkim
MFC after: 3 days
be handled by chn_abort() and chn_start() alone. This should fix
few issues with single duplex hardware (mostly) or pre virtual record
(RELENG 6) under WINE emulation and possibly others that using
SNDCTL_DSP_SETTRIGGER.
MFC after: 3 days
it's multi DAC / playback channels is not that good. Enabling vchans
make the bug more visible since playback allocation will look for
possible free hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has been proven faulty.
Tested by: Dominic Fandrey <LoN_Kamikaze at gmx dot de>
URL: http://lists.freebsd.org/pipermail/freebsd-stable/2007-December/039022.html
that favours true hardware channel, the first instance of recording
request will grab this channel (the first channel is being used as
vchan master). In many cases, it is not really work as intended and give
false impression of broken recording.
PR: kern/118546
MFC after: 3 days
- Enable pcbeep control for Acer + ALC268 (nid 29). Give enough (fake)
hints so the parser will grab it and allocate "speaker" control.
- Fix regression while preparing DAC and ADC for multichannel
format. Since playback policy is to output to every possible path,
ensure that each DAC is started.
Reported / Tested by: Guy Brand
o Acer Aspire 4520 laptop
- jack sensing / automute
o Toshiba Satellite A135-S4527 laptop
- jack sensing / automute
Tested by: lioux
o Apple Macbook 3 (is it?)
- require gpio0 (for speakers) and ovref50 (for headphone)
to make it works
- jack sensing / automute
Tested by: Ed Schouten
* Add Nvidia MCP67 controller ids.
* Be sensible about simmilar controller with multiple pci ids.
* Connect unused DAC/ADC to stream#0 rather than forcing each of them
managing their own stream.
MFC after: 3 days
The reliability of it's multi DAC / playback channels is
not that good. Enabling vchans make the bug more visible
since playback allocation will look for possible free
hardware channels first (i.e: the next DAC, the very first
has been consumed by vchan mixer) which in this case has
been proven faulty.
Reported / Tested by: Sascha Klauder
MFC after: 3 days
to kproc_xxx as they actually make whole processes.
Thos makes way for us to add REAL kthread_create() and friends
that actually make theads. it turns out that most of these
calls actually end up being moved back to the thread version
when it's added. but we need to make this cosmetic change first.
I'd LOVE to do this rename in 7.0 so that we can eventually MFC the
new kthread_xxx() calls.
codecs. Codec at address 0 seems purely digital, or perhaps an HDMI
interface. Let the driver skip it and continue scanning the codecs
starting with address 2 (Realtek ALC885).
* Due to possibilities of future similar cases, put enough logic
in hdac_scan_codecs() to force codec scanning starting from
XX address via tunable "hint.pcm.%d.codec_index".
Reported / Tested by: Toomas Pelberg <toomasp@gmx.net>
- Trivial headphone / speaker automute fixup for Fujitsu-Siemens
AMILO Si 1848 laptop.
Reported / Tested by: Ed <ed@bsd.it>
- Trivial headphone / speaker automute fixup for Fujitsu-Siemens
Lifebook S7020D laptop.
Reported / Tested by: Jaromir Dvoracek <jarek@ataxo.com>
- Some smart vendor trying to create interplanetary wormhole by
screwing pci config space during their BIOS update. The side effects
of their failure attempt includes mutilated hardware id, broken
speaker automuting and loosing the entire analog CD connectivity,
thus causing enough collateral damages to collapse the entire
universe. Move along with it.
Please exercise extra cautious when applying BIOS updates.
Reported / Tested by: Pietro Cerutti <gahr@gahr.ch>
- assembled laptop, based on the MSI-1034
(662) which is now becoming MSI-034A.
- Fix no sound issues (on headphones) for Lenovo ThinkCentre A55 due
to global automute table entry which is not applicable for
non-laptops.
Reported / Tested by: Piotr Smyrak <piotr.smyrak@heron.pl>
- Speaker mute control for HP DC7700 since the front headphone jack
does not generate any interesting unsolicited signal/response.
Reported / Tested by: tyop @ irc.freenode.net
Approved by: re (kensmith)
MFC after: 3 days
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- Add controller id for Intel 82801I (ICH9).
PR: kern/114399
Submitted by: Michael Fuckner <michael@fuckner.net>
- MSI support. Disable by default due to various issues with too many
broken hardwares. MSI can be enabled through device.hints(5) or
kenv(8) by setting "hint.pcm.%d.msi=1".
Partially submitted by: kevlo
YAMAMOTO Taku <taku@tackymt.homeip.net>
Tested by: joel, kevlo, YAMAMOTO Taku
Approved by: re (hrs)
MFC after: 3 days
that should be a no-op (for example, requesting SYNC on record path).
The standards does not indicate that such requests are illegal, so
just return it as success instead of EINVAL.
Approved by: re (mux)
Submitted by: Simon Schubert <corecode@fs.ei.tum.de>
- Defer flushing unsolicited response into taskqueue thread rather
than handle it directly in interrupt handler, since few of its
operations (like measuring/calibrating jack impedance) are quite
expensive.
- Misc. debugging cleanups.
Tested by: joel
Approved by: re (hrs)
MFC after: 3 days
Note: The offending quirk should have been made model/codec specific,
but since there were no records / log which model requires it, the quirk
logic had to be inverted (blacklist instead of whitelist).
Tested by: Arkadiy Dudevitch <dudevitch@englerllc.com>
Approved by: re (hrs)
MFC after: 3 days
eradication in/from userland path, countless locking fixes, etc.
- General sleep call through msleep(9) has been converted to condvar(9)
with better consistencies.
- Heavily guard every possible "slow path" entries (open(), close(),
few ioctl()s, sysctls), but once it entering "fast path" (io, interrupt
started), they are free to fly on their own.
- Rearrange locking sequences, resulting better concurrency and
serialization. Large part doesn't even need locking at all, and will be
removed in future. Less clutter, except in few places due to lock
ordering.
- Anonymous mixer object creation/deletion to simplify mixer handling
beyond typical mixer ioctls.
Submitted by: chibis (with modifications)
- Add few mix_[get|set|..] functions to avoid calling mixer_ioctl()
directly using cryptic arguments.
- Locking fixes to avoid possible deadlock with (still under Giant) USB.
- Better simplex/duplex device handling.
- Recover mmap() functionality for recording, which has been lost
since 2.2.x - 3.x (the introduction of newpcm). Full-duplex mmap still
doesn't work (due to VM/page design), but people still can mmap
both by opening each direction separately. mmaped playback is guarantee
to work either way.
- New sysctl: "hw.snd.compat_linux_mmap" to allow PROT_EXEC page
mapping, due to recent changes in linux compatibility layer which
require it. All linux applications that using sound + mmap() (mostly games)
require this to be enabled. Disabled by default.
- Other goodies.. too many, that will increase releng7 shareholder value
and make users of releng6 (and below) cry ;)
* This commit should be atomic. If anything goes wrong (not counting problem
originated from elsewhere), I will not hesitate to revert everything back
within 12 hours. This substantial changes itself not a rocket science
and the process has begun for almost 2 years, and lots of incremental
changes are already in place during that period of time.
* Some issues does occur in snd_emu10kx (note the 'x') due to various
internal locking issues and it is currently being worked on by chibis.
Tested by: chibis (Yuriy Tsibizov), joel, Alexandre Vieira,
many innocent souls...
- Add codec id for AD1988B, along with fixing its line-in and other
issues (with proper quirks). [2]
Submitted by: [1] barbara.xxx1975@libero.it
[2] Oliver Brandmueller ob@e-Gitt.NET
MFC after: 3 days
seems not enough to verify its consistencies.
- Define AC97_MIXER_SIZE as SOUND_MIXER_NRDEVICES (25), since we
don't need more than that. Stop doing wild and random guess about
its size since we're stricly bound to it.
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
Things can get ugly without it due to uninitialized class. RELENG_6 need
a simmilar, but different treatment as well.
err.. perhaps we should teach devclass_get_maxunit() to return -1 ?
MFC after: 1 day
- Rework the entire pcm_channel structure:
* Remove rarely used link placeholder, instead, make each pcm_channel
as head/link of each own/each other. Unlock - Lock sequence due to
sleep malloc has been reduced.
* Implement "busy" queue which will contain list of busy/active
channels. This greatly reduce locking contention for example while
servicing interrupt for hardware with many channels or when virtual
channels reach its 256 peak channels.
- So I heard you like v chan ... O RLY?
Welcome to Virtual **Record** Channels (vrec, rec vchans, vchans for
recording, Rec-Chan, you decide), the ultimate solutions for your
nagging O_RDWR full-duplex wannabe (note: flash plugins) monopolizing
single record channel causing EBUSY. Vrec works exactly like Vchans
(or, should I rename it to "Vplay" :) , except that it operates on the
opposite direction (recording). Up to 256 vrecs (like vchans) are
possible.
Notes:
* Relocate dev.pcm.%d.{vchans,vchanformat,vchanrate} to each of its
respective node/direction:
dev.pcm.%d.play.* for "play" (cdev = dsp%d.vp%d)
dev.pcm.%d.rec.* for "record" (cdev = dsp%d.vr%d)
* Don't expect that it will magically give you ability to split
"recording source" (eg: 1 channel for cdrom, 1 channel for mic,
etc). Just admit that you only have a *single* recording source /
channel. Please bug your hardware vendor instead :)
- Bump maxautovchans from 4 to 16. For a full-fledged multimedia
desktop/workstation with too many soundservers installed (esound,
artsd, jackd, pulse/polypaudio, ding-dong pling plong mudkip fuh fuh,
etc), 4 seems inadequate. There will be no memory penalty here, since
virtual channels are allocate only by demand.
- Nuke/Rework the entire statically created cdev entries. Everything is
clonable through snd own clone manager which designed to withstand many
kind of abusive devfs droids such as:
* while : ; do /bin/test -e /dev/dsp ; done
* jot 16777216 0 | while read x ; do ls /dev/dsp0.$x ; done
* hundreds (could be thousands) concurrent threads/process opening
"/dev/dsp" (previously, this might result EBUSY even with just
3 contesting threads/procs).
o Reusable clone objects (instead of creating new one like there's no
tomorrow) after certain expiration deadline. The clone allocator will
decide whether to reuse, share, or creating new clone.
o Automatic garbage collector.
- Dynamic unit magic allocator. Maximum attached soundcards can be tuned
using tunable "hw.snd.maxunit" (Default to 512). Minimum is 16, and
maximum is 2048.
- ..other fixes, mostly related to concurrency issues.
joel@ will do the manpage updates on sound(4).
Have fun.
by the subsequent mix_setdevs() and friends.
- Minor style(9) declaration arrangement nit.
Requested by: joeld
Submitted by: pluknet <pluknet@gmail.com>
Neither me nor Ariff have access to any of this hardware, so all tests
have been made by Konstantin and Artem. Commit message mostly written
by Konstantin.
envy24:
- Add test code to support rear line-in input on 'Terratec DMX 6fire'
audio card. This code is also intended to be used in the future for
support of cards, that have I2C-to-GPIO expanders wired between the
control line of the audio codec and the Envy24, however such cards
are too complex and i can't add that support without hardware sample
of such board, i've already tried and failed.
envy24ht:
- Add support for 'AudioTrak Prodigy HD2'.
- Add support for 'AudioTrak Prodigy 7.1 XT'.
- Add support for 'ESI Juli@' (Works ok, DAC volume is hard-coded for
the time being, so 'mixer vol ...' doesn't work, only 'mixer pcm
...' works). [1]
- Fix bug in the init data for M-Audio Revolution 5.1, that
results in distorted sound.
- Add software volume control (now 'mixer pcm' works, thanks to Ariff).
- Add support for more samples rates - 176.4kHz and 192kHz.
- Fix problem with the 192kHz samples rate playback when 24.576MHz
crystal is used on the board instead of 49.152MHz crystal.
spicds:
- Add support for Asahi Kasei flagship DAC - AK4396 (used in AudioTrak
Prodigy HD2).
Submitted by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Tested by: Artem Antonov [1]
Reviewed by: ariff
- http://www.intel.com/design/chipsets/specupdt/245051.htm
AC97 Soft Audio and Soft Modem Master Abort Errata
Issue:
Use of either soft audio or soft modem on an Intel® 82443MX PCISet
based platform running a 100 MHz Processor System Bus and an AC97 codec
may result in failures. The system continues to function normally while
the AC97 hardware may not resume and may require a cold-boot to
recover. As a result of the failure, the Master Abort Status bit will
be set in the audio or modem function PCI header space.
Workaround:
Force uncacheable DMA on both BDL and pcm buffers.
Tested by: Emil Holmstr|m <emil@linux.se>
- Remove explicit call to pmap_change_attr(), since we now have proper
and functional definition of BUS_DMA_NOCACHE.
- Enable PCI(e) bus snooping for non i386/amd64 as an alternative for
uncacheable DMA.
- Codecs changes:
* Analag Device -> Analog Devices, AD1988.
* New codec: VIA VT1708 and VT1709, Realtek ALC262, ALC861-VD and
ALC885.
* Various fixups for Conexant Waikiki, fix recording (read: microphone)
on various Analog Devices codecs due to vendor BIOS mess, various
quirks for several ASUS laptops/boards.
- Fix connection list handling, closely following the specification to
handle range of nids.
- Basic Jack sense polling infrastructure for possible hardwares with
broken unsolicited response interrupt.
Ideas/Submitted/Tested by: Andriy Gapon <avg@icyb.net.ua>,
#freebsd-azalia, many.
and should only be applied on certain specific card / vendor, hence the
addition of ac97_getsubvendor().
- Fix low volume issue on several MSI laptops through ALC655 quirk.
Reported/Tested by: Christian Mueller
<raptor-freebsd-multimedia@xpls.de>
MFC after: 1 week
execution should help us avoiding potential deadlock and illegal locking
while sleeping in various mixer -> usb calls. To enable it, use
hint.uaudio.%d.async="1" or sysctl dev.uaudio.%d.async=1. Default is
disable, to remain compatible with old behaviour (with slight risk of
potential deadlock).
on amd64 and i386) until we gain proper BUS_DMA_NOCACHE support.
(in progress).
Tested by: rafan, infofarmer, Nguyen Tam Chinh <unixvn@gmail.com>
Tested on: amd64, i386
- SWAPLR quirk for (unknown, luckily it is mine) broken uaudio stick.
Fixing by rewiring is impossible without damaging it. Luckily,
we can fix it using "other" methods :) .
- Add uaudio_get_vendor(), _product() and _release() in uaudio.c
(currently used by uaudio_pcm quirk).
- Implement CHANNEL_SETFRAGMENTS().
- Drop channel locking in few places where it is about to sleep
somewhere. This should help eliminating illegal locking acquisition
where the current thread is about to sleep, and also few deadlock
cases. Dropping it right here is quite safe since it is already
protected by CHN_F_BUSY flag and other threads won't bother to touch it.
Solving other illegal locking issues are quite tricky without converting
most usbd_do_request() calls to its equivalent _async() calls,
which I intend to do it later after getting full test report from
other people with different uaudio hardwares.
- Fix memory leak issues during detach. This seems common to any drivers
(notably emu10kx, csapcm?) with bridge functions.
Implement CHANNEL_SETFRAGMENTS() for snd_atiixp, snd_es137x, snd_hda
and snd_via8233. CHANNEL_SETBLOCKSIZE() will basically call
CHANNEL_SETFRAGMENTS() internally using conservative blocksize /
blockcount hints. Other drivers will be converted later.
- Disable stray buffer management, since sample size aligned buffering
are pretty much guaranteed through out the entire feeder_* chain
processes.
- Few style(9) cleanups.
channel.c/channel_if.m:
- Macros cleanups, prefer inlined min() over MIN().
- Rework chn_read()/chn_write() for better dead interrupt detection
policy. Reduce scheduling overhead by doing pure 5 seconds sleep
before giving up, instead of several cycle of brute micro sleeping.
- Avoid calling wakeup_one() for non-sleeping channel (for example,
vchan parent channel).
- EWOULDBLOCK -> EAGAIN.
- Fix possible divide-by-zero panic on chn_sync().
- Re-enforce ^2 blocksize policy, since there are too many broken
userland apps that blindly assume it without even trying to do
serious calculations.
- New channel method - CHANNEL_SETFRAGMENTS(), a refined version of
CHANNEL_SETBLOCKSIZE(). It accept _both_ blocksize and blockcount
arguments, so the driver internals will have better hints for
buffering and timing calculations.
- Hook FEEDER_SWAPLR into feederchain building process.
feeder_fmt.c:
- Unified version of various filters, avoiding duplications.
- malloc()less feeder_fmt. Informations can be retrieved dynamically
by doing table lookup on static data. For cases such as converting
from stereo to mono or reducing bit depth where input data is larger
than output, cycle remaining available free space until it has been
exhausted and start kicking 8 bytes reservoir space from there to
complete the remaining requested count.
- Introduce FEEDER_SWAPLR. Few super broken hardwares (found on several
extremely cheap uaudio stick, possibly others) mistakenly wired left
and right channels wrongly, screwing output or input.
- Rearrange FEEDER_* constants starting from 0 to 31, so the future
additions will be much easier and consistent.
- Introduce FEEDER_SWAPLR. Few super broken hardwares (found on several
extremely cheap uaudio stick, possibly others) mistakenly wired left
and right channels wrongly, screwing output or input.
malloc()less feeder_vchan. Informations can be retrieved dynamically
by doing table lookup on static data. Reduce mixing overhead by
doing direct copy on first channel. Mixing process will begin starting
from second channel onwards.