o Oxford Semiconductor PCI Dual Port Serial
o Netmos Nm9845 PCI Bridge with Dual UART
Add PCI IDs for single-port cards:
o Various SIIG Cyber Serial
o Oxford Semiconductor OXCB950 UART
Update description as per puc(4).
immediately, back off to the next higher Cx sleep state. Some machines
with a Via chipset report a valid C3 but a register read doesn't actually
halt the CPU. This would cause the machine to appear unresponsive as it
repeatedly called cpu_idle() which immediately returned. Causing interrupts
(i.e. by pressing the power button) would cause the system to make forward
progress, showing that it wasn't actually hung.
Also, enable interrupts a little earlier. We don't need them disabled
to calculate the delta time for the read.
Reported by: silby
MFC after: 2 weeks
and increase flexibility to allow various different approaches to be tried
in the future.
- Split struct ithd up into two pieces. struct intr_event holds the list
of interrupt handlers associated with interrupt sources.
struct intr_thread contains the data relative to an interrupt thread.
Currently we still provide a 1:1 relationship of events to threads
with the exception that events only have an associated thread if there
is at least one threaded interrupt handler attached to the event. This
means that on x86 we no longer have 4 bazillion interrupt threads with
no handlers. It also means that interrupt events with only INTR_FAST
handlers no longer have an associated thread either.
- Renamed struct intrhand to struct intr_handler to follow the struct
intr_foo naming convention. This did require renaming the powerpc
MD struct intr_handler to struct ppc_intr_handler.
- INTR_FAST no longer implies INTR_EXCL on all architectures except for
powerpc. This means that multiple INTR_FAST handlers can attach to the
same interrupt and that INTR_FAST and non-INTR_FAST handlers can attach
to the same interrupt. Sharing INTR_FAST handlers may not always be
desirable, but having sio(4) and uhci(4) fight over an IRQ isn't fun
either. Drivers can always still use INTR_EXCL to ask for an interrupt
exclusively. The way this sharing works is that when an interrupt
comes in, all the INTR_FAST handlers are executed first, and if any
threaded handlers exist, the interrupt thread is scheduled afterwards.
This type of layout also makes it possible to investigate using interrupt
filters ala OS X where the filter determines whether or not its companion
threaded handler should run.
- Aside from the INTR_FAST changes above, the impact on MD interrupt code
is mostly just 's/ithread/intr_event/'.
- A new MI ddb command 'show intrs' walks the list of interrupt events
dumping their state. It also has a '/v' verbose switch which dumps
info about all of the handlers attached to each event.
- We currently don't destroy an interrupt thread when the last threaded
handler is removed because it would suck for things like ppbus(8)'s
braindead behavior. The code is present, though, it is just under
#if 0 for now.
- Move the code to actually execute the threaded handlers for an interrrupt
event into a separate function so that ithread_loop() becomes more
readable. Previously this code was all in the middle of ithread_loop()
and indented halfway across the screen.
- Made struct intr_thread private to kern_intr.c and replaced td_ithd
with a thread private flag TDP_ITHREAD.
- In statclock, check curthread against idlethread directly rather than
curthread's proc against idlethread's proc. (Not really related to intr
changes)
Tested on: alpha, amd64, i386, sparc64
Tested on: arm, ia64 (older version of patch by cognet and marcel)
to the actual dates when code actually changed. Also add special case
link state change handling for RELENG_5, which doesn't have
if_link_state_change(). No actual operational changes are done.
of the PCIR_HDRTYPE register. It's the value returned from this
read access that determines whether or not we decide a device is
present at the current slot index. For some reason that I can't
adequately explain, this read fails on my machine when probing the
USB controller on my machine (which happens a multifunction device
at slot index 3 hung off the PCI-PCI bridge on the AMD8111 (bus
index 1)). The read will return 0xFF even though it should return
0x80 to indicate the presence of a multifunction device.
As near as I can tell, there's some timing issue involved with reading
the 'dead' slot indexes 0 through 2 that causes the read of the actual
device at slot 3 to fail. I tried a couple of different tricks to
correct the problem (the patch to amd64/pci/pci_cfgreg.c fixes it
for the amd64 arch), but adding this delay is the only thing that
always allows the USB controllers to be correctly probed 100% of the
time. Whatever the problem is, it's likely confined to the AMD8111
chipset. However, a simple 1us delay is fairly harmless and should
have no side effects for other hardware. I consider this to be
voodoo, but it's fairly benign voodoo and it makes my USB keyboard
and mouse work again.
Note that this is the second time that I've had to resort to a
1us delay to fix a PCI-related problem with this AMD8111/Opteron
system (the first being a fix I made a while back to the NDISulator).
It's possible the delay really belongs in the cfgreg code itself,
or that pci_cfgreg needs some custom hackery for an errata in the
8111. (I checked but couldn't find any documented errata on AMD's
site that could account for these problems.)
- Move hardware counter reading/zeroing to hme_tick(). This saves
8 register access per interrupt. [1]
- Use imax macro for getting max. argument between two integers.
- Invoke bus_dmamap_sync(9) first before freeing mbuf.
- Check driver queue first to reduce locking operation in hme_start_locked()
and interrupt handler.
- Simplyfy watchdog timer setup in interrupt handler.
- Don't log normal errors such as RX overrun. If we have DMA stuck
condition, reinitialize the driver and log it.
Reviewed by: marius
Obtained from: OpenBSD [1]
confused with the Credit Card Adapter II and its spawn (which the xe
driver supports). These changes get my card probing and attaching. I
recently won one of these (and a NEC rebadged version) in an lot
auction. The NEC didn't work, so I took it apart and found the
MB86960A chip and then modified if_fe_pccard.c to attach. I can't
test this card further since I have no dongle for this card.
is on AC power (i.e. not a laptop). This allows power_profile to run once
for desktop systems as well, for instance, to set C3 or CPU frequency.
MFC after: 2 weeks
support the CM-battery interface. Smart batteries can eventually be
supported without ACPI via a separate SMBus interface. The ACPI interface
uses the embedded controller for reading/writing to the SMBus, and normal
ASL definitions for locating the battery controller (since SMBus can't be
enumerated.) Also import definitions for the smart battery interface.
This was written by Hans Petter Selasky with minor cleanups from myself.
Submitted by: Hans Petter Selasky <hselasky / c2i.net>
* Use ACPI_BATT_UNKNOWN instead of constants
* Use maxunit instead of a count of devices since we may have sparse
battery devices in the future. Only userland should be using unit
numbers anyway, so provide a translation function. (Kernel use of
batteries should be restricted to looking up a device_t and calling
methods directly.
* Don't check acpi_BatteryIsPresent() in acpi_battery. Leave it up to
the hardware-specific driver (i.e. cmbat) since smart batteries seem
to not report the "battery present" flag.
* Convert mA to mW if the battery uses those units. CM-batteries only
used mW so this deficiency went unnoticed.
* Clean strings reported in the battery info from any control chars.
* Only dereference the unit from ioctl_arg if the full struct is present.
Unit wouldn't have been used later if it wasn't present but this is
cleaner. Translate the unit if it's not ACPI_BATTERY_ALL_UNITS.
* bzero structs before returning them to usermode for future compat.
Most of this work was submitted by Hans Petter Selasky and then majorly
reworked by myself.
Submitted by: Hans Petter Selasky <hselasky / c2i.net>
attach routine. Go ahead and ask for it in the probe routine and be
just as wrong as all the other cards that ask for it there...
# this gets the RTL8019 on a SBC at work fully functional. 6.0 still treats
# the 8019 as a generic NE-2000, so these changes aren't relevant there.
ed_probe_rtl80x9. In the pci case we call ed_probe_rtl80x9 first. In
the PCI case we were using the correct nic_offset by accident because
softc is initialized to zero. In the isa case we were using the wrong
value by accident, since ed_probe_WD80x3 sets the offset value to
0x10. This lead to the identification routines failing. Fix this
problem by always initalizing the nic_offset and asic_offset before
making ed_{asic,nic}_{in,out}* calls.
- Destroy mutex in case of attach failure. [1]
- Lock properly em_watchdog(). [1]
- Lock properly em_sysctl_int_delay(). [1]
- Remove unused global adapter linked list.
- Remove unused dma_size field from struct em_dma_alloc.
- Do not touch interface statistics, that must be edited
only by upper layers. [1]
Submitted by: yongari [1]
o Do not mask the RX overrun interrupt.
o Rewrite em_intr():
- Axe EM_MAX_INTR.
- Cycle acknowledging interrupts and processing
packets until zero interrupt cause register is
read.
- If RX overrun comes in log this fact. [ NetBSD also
resets adapter in this case, but my tests showed that
this is not needed and only pessimizes behavior under
heavy load. ]
- Since almost all functions is rewritten, style the
remaining lines.
This fixes em(4) interfaces wedging under high load.
In collaboration with: wpaul, cognet
Obtained from: NetBSD
flag. This fixes panic, when 'ifconfig em0 down' was called and it calls
em_stop() while the em_process_receive_interrupts() has temporarily
dropped the lock.
sampling rate:
- Improve vchan chn_setspeed() strategy. Try to avoid FEEDER_RATE
on parent channel if the requested value is not supported
by the hardware.
- Fix vchan default speed calculation. In any case, vchan should
rely on parent bufsoft speed instead of bufhard since it is
possible that the entire feeder chain might involve FEEDER_RATE.
This is possible under extreme, rare condition if the above
chn_setspeed() strategy failed.
Approved by: netchild (mentor)
- Change ndis_return() from a DPC to a workitem so that it doesn't
run at DISPATCH_LEVEL (with the dispatcher lock held).
- In if_ndis.c, submit packets to the stack via (*ifp->if_input)() in
a workitem instead of doing it directly in ndis_rxeof(), because
ndis_rxeof() runs in a DPC, and hence at DISPATCH_LEVEL. This
implies that the 'dispatch level' mutex for the current CPU is
being held, and we don't want to call if_input while holding
any locks.
- Reimplement IoConnectInterrupt()/IoDisconnectInterrupt(). The original
approach I used to track down the interrupt resource (by scanning
the device tree starting at the nexus) is prone to problems when
two devices share an interrupt. (E.g removing ndis1 might disable
interrupts for ndis0.) The new approach is to multiplex all the
NDIS interrupts through a common internal dispatcher (ntoskrnl_intr())
and allow IoConnectInterrupt()/IoDisconnectInterrupt() to add or
remove interrupts from the dispatch list.
- Implement KeAcquireInterruptSpinLock() and KeReleaseInterruptSpinLock().
- Change the DPC and workitem threads to use the KeXXXSpinLock
API instead of mtx_lock_spin()/mtx_unlock_spin().
- Simplify the NdisXXXPacket routines by creating an actual
packet pool structure and using the InterlockedSList routines
to manage the packet queue.
- Only honor the value returned by OID_GEN_MAXIMUM_SEND_PACKETS
for serialized drivers. For deserialized drivers, we now create
a packet array of 64 entries. (The Microsoft DDK documentation
says that for deserialized miniports, OID_GEN_MAXIMUM_SEND_PACKETS
is ignored, and the driver for the Marvell 8335 chip, which is
a deserialized miniport, returns 1 when queried.)
- Clean up timer handling in subr_ntoskrnl.
- Add the following conditional debugging code:
NTOSKRNL_DEBUG_TIMERS - add debugging and stats for timers
NDIS_DEBUG_PACKETS - add extra sanity checking for NdisXXXPacket API
NTOSKRNL_DEBUG_SPINLOCKS - add test for spinning too long
- In kern_ndis.c, always start the HAL first and shut it down last,
since Windows spinlocks depend on it. Ntoskrnl should similarly be
started second and shut down next to last.
the descriptors set.
- In em_process_receive_interrupts(), call bus_dmamap_sync() for the
descriptors set each time we modify one descriptor, instead of doing it only
at the function exit, to make sure the adapters know he can re-use the
descriptor.
This helps on arm with write-back data cache (and possibly on other arches
with bounce pages, I don't know) under heavy network load. Without this,
if we attempt to process more than num_rx_desc descriptors, the adapter
would just stop processing rx interrupts.
the former is the ISA part, not the latter.
MFC After 6.0 is unfrozen (this bug doesn't exist in 6.0 because I didn't
MFC the rtl80x9 changes for ISA due to an error on my part)
to the 100/1000 BCM5400 phy. This fixes the problem with
the GEM port not syncing up on Sawtooth G4's.
Obtained from: NetBSD
Reported by: Ben Rosengart <ben + freebsd org at narcissus net>
cards and teach the re(4) driver to attach to revision 3 cards.
Submitted by: Fredrik Lindberg fli+freebsd-current at shapeshifter dot se
MFC after: 2 weeks
Reviewed by: imp, mdodd
originally wrote it for 4.x and hasn't really had the time to fully update
it to 5.x and later. Also, the author doesn't use the hardware anymore as
well. If someone does need this driver they can always resurrect it from
the Attic.
Requested by: Frank Mayhar frank at exit dot com
do not support the GETINFO immediate command, unlike just about every other
variant of the hardware. Also document some magic values and fix some minor
nearby whitespace.
MFC After: 3 days
The receive function em_process_receive_interrupts() unlocks the
adapter while ether_input() processes the packet, and then locks
it back. In the meantime, em_init() may be called, either from
em_watchdog() from softclock interrupt or from the ifconfig(8)
program. The em_init() resets the card, in particular it sets
adapter->next_rx_desc_to_check to 0 and resets hardware RX Head
and Tail descriptor pointers. The loop in
em_process_receive_interrupts() does not expect these things to
change, and a mess may result.
This fixes long wedges of em(4) interfaces receive part under high
load and IP fastforwarding enabled.
PR: kern/87418
Submitted by: Dmitrij Tejblum <tejblum yandex-team.ru>
