added/removed interfaces in a more consistent manner and reloading the
configuration file.
- Implement burst unsolicited RA sending into the internal RA timer framework
when AdvSendAdvertisements and/or configuration entries are changed as
described in RFC 4861 6.2.4. This fixes issues that make termination of the
rtadvd(8) daemon take very long time.
An interface now has three internal states, UNCONFIGURED, TRANSITIVE, or
CONFIGURED, and the burst unsolicited sending happens in TRANSITIVE.
See rtadvd.h for the details.
- rtadvd(8) now accepts non-existent interfaces as well in the command line.
- Add control socket support and rtadvctl(8) utility to show the RA information
in rtadvd(8). Dumping by SIGUSR1 has been removed in favor of it.
added/removed interfaces in a more consistent manner and reloading
the configuration file.
- Add initial support for control socket. RA information in the
daemon can be obtained by rtadvctl(8) instead of SIGUSR1 in a similar
manner to ifconfig(8). The information dump has been removed in favor of it.
(reload the configuration file)
# rtadvctl reload
(show RA messages being sent on each interfaces)
# rtadvctl show
em0: flags=<UP,CONFIGURED,PERSIST> status=<RA_SEND> mtu 1280
DefaultLifetime: 30m
MinAdvInterval/MaxAdvInterval: 3m20s/3m20s
AdvLinkMTU: <none>, Flags: O, Preference: medium
ReachableTime: 0s, RetransTimer: 0s, CurHopLimit: 64
AdvIfPrefixes: yes
(show RA messages being sent only on em0)
# rtadvctl show em0
(rtadvctl -v show provides additional information)
# rtadvctl -v show em0
em0: flags=<UP,CONFIGURED,PERSIST> status=<RA_SEND> mtu 1280
DefaultLifetime: 30m
MinAdvInterval/MaxAdvInterval: 3m20s/3m20s
AdvLinkMTU: <none>, Flags: O, Preference: medium
ReachableTime: 0s, RetransTimer: 0s, CurHopLimit: 64
AdvIfPrefixes: yes
Prefixes (1):
2001:db8:1::/64 (CONFIG, vltime=30d, pltime=7d, flags=LA)
RDNSS entries:
2001:db8:1::128 (ltime=2m40s)
(stop rtadvd)
# rtadvctl shutdown
A remaining issue when reloading the configuration file is that
during that period rtadvd cannot communicate with rtadvctl due to some
additional RA sending for graceful shutdown. This will be fixed later.
- Fix a missing back pointer assignment in struct prefix to struct rainfo
when addr="" is specified. This caused SIGSEGV.
- Insert a prefix element to a tail queue after setting parameters.
Options for DNS Configuration) into rtadvd(8) and rtsold(8). DNS
information received by rtsold(8) will go to resolv.conf(5) by
resolvconf(8) script. This is based on work by J.R. Oldroyd (kern/156259)
but revised extensively[1].
- rtadvd(8) now supports "noifprefix" to disable gathering on-link prefixes
from interfaces when no "addr" is specified[2]. An entry in rtadvd.conf
with "noifprefix" + no "addr" generates an RA message with no prefix
information option.
- rtadvd(8) now supports RTM_IFANNOUNCE message to fix crashes when an
interface is added or removed.
- Correct bogus ND_OPT_ROUTE_INFO value to one in RFC 4191.
Reviewed by: bz[1]
PR: kern/156259 [1]
PR: bin/152458 [2]
- deprecate routes#N, as it is hard to keep consistency with
rtprefixN. accept any number of "rtprefix", "rtrefix0",
..., "rtprefix99".
- deprecate "addrs#N", as it is difficult for users to keep
consistency with "addrN".
accept 100 prefix info in maximum - like "addr", "addr0"
... "addr99". WARNS=2 clean on netbsd.
old configuration file should work just fine.
behavior change:
previously, we rejected "addrN" if there's "addr", and we rejected
"addr" if there is "addrN". now we accept both without problem.
- when an advertised prefix configured from the kernel has been added
or invalidated, notice the change in a short delay.
- when invalidating a prefix, do not bark even if there is
inconsistency about prefix lifetimes.
- wrap more specific route info code into ROUTEINFO.
Obtained from: KAME
MFC after: 1 week
was removed from the kernel;
Advertise the prefix with zero lifetimes rather than to remove the prefix
from the prefix list to be advertised.
This will help renumber a receiving host by deprecating the address
derived from the old prefix.
Obtained from: KAME
MFC after: 2 weeks
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
KAME put INET6 related stuff into sys/netinet6 dir, but IPv6
standard API(RFC2553) require following files to be under sys/netinet.
netinet/ip6.h
netinet/icmp6.h
Now those header files just include each following files.
netinet6/ip6.h
netinet6/icmp6.h
Also KAME has netinet6/in6.h for easy INET6 common defs
sharing between different BSDs, but RFC2553 requires only
netinet/in.h should be included from userland.
So netinet/in.h also includes netinet6/in6.h inside.
To keep apps portability, apps should not directly include
above files from netinet6 dir.
Ideally, all contents of,
netinet6/ip6.h
netinet6/icmp6.h
netinet6/in6.h
should be moved into
netinet/ip6.h
netinet/icmp6.h
netinet/in.h
but to avoid big changes in this stage, add some hack, that
-Put some special macro define into those files under neitnet
-Let files under netinet6 cause error if it is included
from some apps, and, if the specifal macro define is not
defined.
(which should have been defined if files under netinet is
included)
-And let them print an error message which tells the
correct name of the include file to be included.
Also fix apps which includes invalid header files.
Approved by: jkh
Obtained from: KAME project
