will remain in the disabled state until another link event happens in the
future (if at all). Add a timer to periodically check the interface state and
recover.
Reported by: Nik Lam <freebsdnik j2d.lam.net.au>
MFC after: 3 days
re-organizing the monitor return logic. We perform interface monitoring
checks after we have determined if the CRC is still on the packet, if
it is, m_adj() is called which will adjust the packet length. This
ensures that we are not including CRC lengths in the byte counters for
each packet.
Discussed with: andre, glebius
that we might have address collisions, so make sure that this hardware address
isn't already in use on another bridge.
Submitted by: csjp
MFC after: 1 month
destination interface as a member of our bridge or this is a unicast packet,
push it through the bpf(4) machinery.
For broadcast or multicast packets, don't bother with the bpf(4) because it will
be re-injected into ether_input. We do this before we pass the packets through
the pfil(9) framework, as it is possible that pfil(9) will drop the packet or
possibly modify it, making it very difficult to debug firewall issues on the
bridge.
Further, implemented IFF_MONITOR for bridge interfaces. This does much the same
thing that it does for regular network interfaces: it pushes the packet to any
bpf(4) peers and then returns. This bypasses all of the bridge machinery,
saving mutex acquisitions, list traversals, and other operations performed by
the bridging code.
This change to the bridging code is useful in situations where individuals use a
bridge to multiplex RX/TX signals from two interfaces, as is required by some
network taps for de-multiplexing links and transmitting the RX/TX signals
out through two separate interfaces. This behaviour is quite common for network
taps monitoring links, especially for certain manufacturers.
Reviewed by: thompsa
MFC after: 1 month
Sponsored by: Seccuris Labs
- use the cu_bridge_id rather than the cu_rootid for the bridge address [1]
- the memcmp return value is not signed so the wrong interface may have been
selected
- fix up the calculation of sc_bridge_id
PR: kern/93909 [1]
MFC after: 3 days
and want to have crypto support loaded as KLD. By moving zlib to separate
module and adding MODULE_DEPEND directives, it is possible to use such
configuration without complication. Otherwise, since IPSEC is linked with
zlib (just like crypto.ko) you'll get following error:
interface zlib.1 already present in the KLD 'kernel'!
Approved by: cognet (mentor)
zero in this case.) A kernel driver has IFF_DRV_RUNNING
at its full disposal while IFF_UP may be toggled only by
humans or their daemonic deputies from the userland.
MFC after: 3 days
did not stop at the right node. Change the backtracking check from
smaller-than to smaller-or-equal to prevent this from happening.
While here fix one additional problem where the insertion of the
default route traversed the entire tree.
PR: kern/38752
Submitted by: qingli (before I became committer)
Reviewed by: andre
MFC after: 3 days
filtering mechanisms to use the new rwlock(9) locking API:
- Drop the variables stored in the phil_head structure which were specific to
conditions and the home rolled read/write locking mechanism.
- Drop some includes which were used for condition variables
- Drop the inline functions, and convert them to macros. Also, move these
macros into pfil.h
- Move pfil list locking macros intp phil.h as well
- Rename ph_busy_count to ph_nhooks. This variable will represent the number
of IN/OUT hooks registered with the pfil head structure
- Define PFIL_HOOKED macro which evaluates to true if there are any
hooks to be ran by pfil_run_hooks
- In the IP/IP6 stacks, change the ph_busy_count comparison to use the new
PFIL_HOOKED macro.
- Drop optimization in pfil_run_hooks which checks to see if there are any
hooks to be ran, and returns if not. This check is already performed by the
IP stacks when they call:
if (!PFIL_HOOKED(ph))
goto skip_hooks;
- Drop in assertion which makes sure that the number of hooks never drops
below 0 for good measure. This in theory should never happen, and if it
does than there are problems somewhere
- Drop special logic around PFIL_WAITOK because rw_wlock(9) does not sleep
- Drop variables which support home rolled read/write locking mechanism from
the IPFW firewall chain structure.
- Swap out the read/write firewall chain lock internal to use the rwlock(9)
API instead of our home rolled version
- Convert the inlined functions to macros
Reviewed by: mlaier, andre, glebius
Thanks to: jhb for the new locking API
- code expects memcmp() to return a signed value, our memcmp() returns 0 if
args are equal and > 0 if not.
- It's possible to hijack interface for static entry. If bridge recieves
packet from interface marked as learning it will replace the bridge_rtnode
entry for the source address even if such entry marked as static.
Submitted by: Gleb Kurtsov <k-gleb yandex.ru>
MFC after: 3 days
beginning and simply refuse to attach to a parent without either
flag.
Our network stack cannot handle well IFF_BROADCAST or IFF_MULTICAST
on an interface changing on the fly. E.g., IP will or won't assign
a broadcast address to an interface and join the all-hosts multicast
group on it depending on its IFF_BROADCAST and IFF_MULTICAST settings.
Should the flags alter later, IP will miss the change and keep using
bogus settings. This can lead to evil things like supplying an
invalid broadcast address or trying to leave a multicast group that
hasn't been joined. So just avoid touching the flags since an
interface was created. This has no practical purpose.
Discussed with: -net, glebius, oleg
MFC after: 1 week
work by yar, thompsa and myself. The checksum offloading part also involves
work done by Mihail Balikov.
The most important changes:
o Instead of global linked list of all vlan softc use a per-trunk
hash. The size of hash is dynamically adjusted, depending on
number of entries. This changes struct ifnet, replacing counter
of vlans with a pointer to trunk structure. This change is an
improvement for setups with big number of VLANs, several interfaces
and several CPUs. It is a small regression for a setup with a single
VLAN interface.
An alternative to dynamic hash is a per-trunk static array with
4096 entries, which is a compile time option - VLAN_ARRAY. In my
experiments the array is not an improvement, probably because such
a big trunk structure doesn't fit into CPU cache.
o Introduce an UMA zone for VLAN tags. Since drivers depend on it,
the zone is declared in kern_mbuf.c, not in optional vlan(4) driver.
This change is a big improvement for any setup utilizing vlan(4).
o Use rwlock(9) instead of mutex(9) for locking. We are the first
ones to do this! :)
o Some drivers can do hardware VLAN tagging + hardware checksum
offloading. Add an infrastructure for this. Whenever vlan(4) is
attached to a parent or parent configuration is changed, the flags
on vlan(4) interface are updated.
In collaboration with: yar, thompsa
In collaboration with: Mihail Balikov <mihail.balikov interbgc.com>
however IPv4-in-IPv4 tunnels are now stable on SMP. Details:
- Add per-softc mutex.
- Hold the mutex on output.
The main problem was the rtentry, placed in softc. It could be
freed by ip_output(). Meanwhile, another thread being in
in_gif_output() can read and write this rtentry.
Reported by: many
Tested by: Alexander Shiryaev <aixp mail.ru>
Vararg functions have a different calling convention than regular
functions on amd64. Casting a varag function to a regular one to
match the function pointer declaration will hide the varargs from
the caller and we will end up with an incorrectly setup stack.
Entirely remove the varargs from these functions and change the
functions to match the declaration of the function pointers.
Remove the now unnecessary casts.
Lots of explanations and help from: peter
Reviewed by: peter
PR: amd64/89261
MFC after: 6 days
may have changed by m_pullup() during fastforward processing.
While this is a bug it is actually never triggered in real world
situations and it is not remotely exploitable.
Found by: Coverity Prevent(tm)
Coverity ID: CID780
Sponsored by: TCP/IP Optimization Fundraise 2005
restored when its removed from the bridge.
At the moment we only clear IFCAP_TXCSUM. Since a locally generated packet on
the bridge may be sent out any one or more interfaces it cant be assumed that
every card does hardware csums. Most bridges don't generate a lot of traffic
themselves so turning off offloading won't hurt, bridged packets are
unaffected.
Tested by: Bruce Walker (bmw borderware.com)
MFC after: 5 days
ef_clone(); we were testing the original ifnet, not the one allocated.
When aborting ef_clone() due to if_alloc() failing, free the allocated
efnet structure rather than leaking it.
Noticed by: Coverity Prevent analysis tool
MFC after: 3 days
SLIST_FOREACH_SAFE() rather than SLIST_FOREACH(), as elements are
freed on each iteration of the loop. This prevents use-after-free.
Noticed by: Coverity Prevent analysis tool
MFC after: 3 days
attempted to cast a struct ifnet to a struct fw_com which resulted in
data corruption.
PR: kern/91307
Submitted by: Alex Semenyaka <alex at semenyaka do ru>
MFC After: 6 days
ETHERTYPE_IPV6 frames. Change this to be a sysctl knob so that is able to still
bridge non-IP packets if desired.
Also return early if all pfil_* sysctls are turned off, the user obviously does
not want to filter on the bridge.
interfaces to bridges, which will then send and receive IP protocol 97 packets.
Packets are Ethernet frames with an EtherIP header prepended.
Obtained from: NetBSD
MFC after: 2 weeks
case if memory allocation failed.
- Remove fourth argument from VLAN_INPUT_TAG(), that was used
incorrectly in almost all drivers. Indicate failure with
mbuf value of NULL.
In collaboration with: yongari, ru, sam
span ports when they disappear. The span port does not have a pointer to the
softc so revert r1.31 and bring back the softc linked-list.
MFC after: 2 weeks
Use the following kernel configuration option to enable:
options BPF_JITTER
If you want to use bpf_filter() instead (e. g., debugging), do:
sysctl net.bpf.jitter.enable=0
to turn it off.
Currently BIOCSETWF and bpf_mtap2() are unsupported, and bpf_mtap() is
partially supported because 1) no need, 2) avoid expensive m_copydata(9).
Obtained from: WinPcap 3.1 (for i386)
- In ifc_name2unit(), disallow leading zeroes in a unit.
Exploit: ifconfig lo01 create
- In ifc_name2unit(), properly handle overflows. Otherwise,
either of two local panic()'s can occur, either because
no interface with such a name could be found after it was
successfully created, or because the code will bogusly
assume that it's a wildcard (unit < 0 due to overflow).
Exploit: ifconfig lo<overflowed_integer> create
- Previous revision made the following sequence trigger
a KASSERT() failure in queue(3):
Exploit: ifconfig lo0 destroy; ifconfig lo0 destroy
This is because IFC_IFLIST_REMOVE() is always called
before ifc->ifc_destroy() has been run, not accounting
for the fact that the latter can fail and leave the
interface operating (like is the case for "lo0").
So we ended up calling LIST_REMOVE() twice. We cannot
defer IFC_IFLIST_REMOVE() until after a call to
ifc->ifc_destroy() because the ifnet may have been
removed and its memory has been freed, so recover from
this by re-inserting the ifnet in the cloned interfaces
list if ifc->ifc_destroy() indicates a failure.
If the packet is rejected from pfil(9) then continue the loop rather than
returning, this means that we can still try to send it out the remaining
interfaces but more importantly the mbuf is freed and refcount decremented on
exit.
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
copy of Ethernet address.
- Change iso88025_ifattach() and fddi_ifattach() to accept MAC
address as an argument, similar to ether_ifattach(), to make
this work.
softc lists and associated mutex are now unused so these have been removed.
Calling if_clone_detach() will now destroy all the cloned interfaces for the
driver and in most cases is all thats needed to unload.
Idea by: brooks
Reviewed by: brooks
Having an additional MT_HEADER mbuf type is superfluous and redundant
as nothing depends on it. It only adds a layer of confusion. The
distinction between header mbuf's and data mbuf's is solely done
through the m->m_flags M_PKTHDR flag.
Non-native code is not changed in this commit. For compatibility
MT_HEADER is mapped to MT_DATA.
Sponsored by: TCP/IP Optimization Fundraise 2005
promisc flag from the member interface, this is a no-op anyway since the
interface is disappearing. The driver may have already released
its resources such as miibus and this is likely to panic the kernel.
Submitted and tested by: Wojciech A. Koszek
MFC after: 2 weeks
OR the flags bits with the driver managed status flags. This fixes an
issue where RUNNING flags would not be reported to processes, which
conflicts with the flags information provided by ifconfig(8).
that the following funtions are not used, wrap in '#ifdef noused' for the
moment.
bstp_enable_change_detection
bstp_disable_change_detection
bstp_set_bridge_priority
bstp_set_port_priority
bstp_set_path_cost
- move the function pointer definitions to if_bridgevar.h
- move most of the logic to the new BRIDGE_INPUT and BRIDGE_OUTPUT macros
- remove unneeded functions from if_bridgevar.h and sort a little.
Use bridge_ifdetach() to notify the bridge that a member has been detached. The
bridge can then remove it from its interface list and not try to send out via a
dead pointer.
cloner. This ensures that ifc->ifc_units is not prematurely freed in
if_clone_detach() before the clones are destroyed, resulting in memory modified
after free. This could be triggered with if_vlan.
Assert that all cloners have been destroyed when freeing the memory.
Change all simple cloners to destroy their clones with ifc_simple_destroy() on
module unload so the reference count is properly updated. This also cleans up
the interface destroy routines and allows future optimisation.
Discussed with: brooks, pjd, -current
Reviewed by: brooks
http://lists.freebsd.org/pipermail/cvs-src/2004-October/033496.html
The same problem applies to if_bridge(4), too.
- Copy-and-paste the if_bridge(4) related block from
if_ethersubr.c to ng_ether.c
- Add XXXs, so that copy-and-paste would be noticed by
any future editors of this code.
- Also add XXXs near if_bridge(4) declarations.
Silence from: thompsa
module name to something that wouldn't conflict with
sys/dev/firewire/firewire.c.
Submitted by: Cai, Quanqing <caiquanqing at gmail dot com>
PR: kern/82727
MFC after: 3 days
opt_device_polling.h
- Include opt_device_polling.h into appropriate files.
- Embrace with HAVE_KERNEL_OPTION_HEADERS the include in the files that
can be compiled as loadable modules.
Reviewed by: bde
to the parent interface, such as IFF_PROMISC and
IFF_ALLMULTI. In addition, vlan(4) gains ability
to migrate from one parent to another w/o losing
its own flags.
PR: kern/81978
MFC after: 2 weeks
as it is done for usual promiscuous mode already. This info is important
because promiscuous mode in the hands of a malicious party can jeopardize
the whole network.
o Axe poll in trap.
o Axe IFF_POLLING flag from if_flags.
o Rework revision 1.21 (Giant removal), in such a way that
poll_mtx is not dropped during call to polling handler.
This fixes problem with idle polling.
o Make registration and deregistration from polling in a
functional way, insted of next tick/interrupt.
o Obsolete kern.polling.enable. Polling is turned on/off
with ifconfig.
Detailed kern_poll.c changes:
- Remove polling handler flags, introduced in 1.21. The are not
needed now.
- Forget and do not check if_flags, if_capenable and if_drv_flags.
- Call all registered polling handlers unconditionally.
- Do not drop poll_mtx, when entering polling handlers.
- In ether_poll() NET_LOCK_GIANT prior to locking poll_mtx.
- In netisr_poll() axe the block, where polling code asks drivers
to unregister.
- In netisr_poll() and ether_poll() do polling always, if any
handlers are present.
- In ether_poll_[de]register() remove a lot of error hiding code. Assert
that arguments are correct, instead.
- In ether_poll_[de]register() use standard return values in case of
error or success.
- Introduce poll_switch() that is a sysctl handler for kern.polling.enable.
poll_switch() goes through interface list and enabled/disables polling.
A message that kern.polling.enable is deprecated is printed.
Detailed driver changes:
- On attach driver announces IFCAP_POLLING in if_capabilities, but
not in if_capenable.
- On detach driver calls ether_poll_deregister() if polling is enabled.
- In polling handler driver obtains its lock and checks IFF_DRV_RUNNING
flag. If there is no, then unlocks and returns.
- In ioctl handler driver checks for IFCAP_POLLING flag requested to
be set or cleared. Driver first calls ether_poll_[de]register(), then
obtains driver lock and [dis/en]ables interrupts.
- In interrupt handler driver checks IFCAP_POLLING flag in if_capenable.
If present, then returns.This is important to protect from spurious
interrupts.
Reviewed by: ru, sam, jhb
replacement and has additional features which make it superior.
Discussed on: -arch
Reviewed by: thompsa
X-MFC-after: never (RELENG_6 as transition period)
copied mbuf, which keeps the IP header 32-bit aligned. This copied mbuf is
reinjected back into ether_input and off to the IP routines.
Reported and tested by: Peter van Dijk
Approved by: mlaier (mentor)
MFC after: 3 days
- Rearrange code so that in a case of failure the affected
route is not changed. Otherwise, a bogus rtentry will be
left and later rt_check() can recurse on its lock. [1]
- Remove comment about protocol cloning.
- Fix two places where rtentry mutex was recursed on, because
accessed via two different pointers, that were actually pointing
to the same rtentry in some cases. [1]
- Return EADDRINUSE instead of bogus EDQUOT, in case when gateway
uses the same route. [2]
Reported & tested by: ps, Andrej Zverev <az inec.ru> [1]
PR: kern/64090 [2]
panics, which occur when stale ifnet pointers are left in struct
moptions hung off of inpcbs:
- Add in_ifdetach(), which matches in6_ifdetach(), and allows the
protocol to perform early tear-down on the interface early in
if_detach().
- Annotate that if_detach() needs careful consideration.
- Remove calls to in_pcbpurgeif0() in the handling of SIOCDIFADDR --
this is not the place to detect interface removal! This also
removes what is basically a nasty (and now unnecessary) hack.
- Invoke in_pcbpurgeif0() from in_ifdetach(), in both raw and UDP
IPv4 sockets.
It is now possible to run the msocket_ifnet_remove regression test
using HEAD without panicking.
MFC after: 3 days
- Use __func__ consistently instead of copying function name
to message strings. Code tends to migrate around source files.
- DIAGNOSTIC is for information, INVARIANTS is for panics.
m_tag_locate(). This adds little overhead of a simple
bitwise operation in case hardware VLAN acceleration
is on, yet saves the more expensive function call if
the acceleration is off.
Reviewed by: ru, glebius
X-MFC-after: 6.0
locks were not aquired because the user buffers were not wired, thus it was
possible that that SYSCTL_OUT could sleep, causing a number of different
problems such as lock ordering issues and dead locks.
-Wire user supplied buffer to ensure SYSCTL_OUT will not sleep.
-Pickup ifnet locks to protect the list.
-Where applicable pickup address locks.
-Pickup radix node head locks.
-Remove splnet stubs
-Remove various comments about locking here, because they are no
longer needed.
It is the hope that these changes will make sysctl_rtsock MP safe.
MFC after: 3 weeks
assigned to the interface.
IPv6 auto-configuration is disabled. An IPv6 link-local address has a
link-local scope within one link, the spec is unclear for the bridge case and
it may cause scope violation.
An address can be assigned in the usual way;
ifconfig bridge0 inet6 xxxx:...
Tested by: bmah
Reviewed by: ume (netinet6)
Approved by: mlaier (mentor)
MFC after: 1 week
refresh the PID which has the descriptor open. The PID is refreshed in various
operations like ioctl(2), kevent(2) or poll(2). This produces more accurate
information about current bpf consumers. While we are here remove the bd_pcomm
member of the bpf stats structure because now that we have an accurate PID we
can lookup the via the kern.proc.pid sysctl variable. This is the trick that
NetBSD decided to use to deal with this issue.
Special care needs to be taken when MFC'ing this change, as we have made a
change to the bpf stats structure. What will end up happening is we will leave
the pcomm structure but just mark it as being un-used. This way we keep the ABI
in tact.
MFC after: 1 month
Discussed with: Rui Paulo < rpaulo at NetBSD dot org >
value from an m_tag, but also to set it. This reduces
complex code duplication and improves its readability.
Alas, we shouldn't rename the macro to VLAN_TAG_LVALUE()
globally because that would cause pain for kernel module
port maintainers and vendors using FreeBSD as their codebase.
Added a clarifying comment instead.
Discussed with: ru, glebius
X-MFC-After: 6.0-RELEASE (MFC is good just to reduce the diff)
attached.
This is caused by bpf_detachd clearing IFF_PROMISC on the interface which does
a SIOCSIFFLAGS ioctl. The problem here is that while the interface has been
stopped, IFF_UP has not been cleared so IFF_UP != IFF_DRV_RUNNING, this causes
the ioctl function to init() the interface which resets the callouts.
The destroy then completes and frees the softc but softclock will panic on a
dead callout pointer.
Ensure ifp->if_flags matches reality by clearing IFF_UP when we destroy.
Silence from: rwatson
Approved by: mlaier (mentor)
MFC after: 3 days
through locking; leave some spl references around code where there
are open questions about global variable references. Also, add
an XXX regarding locking in sysctl.
MFC after: 3 days
actually 1514, so comparing the mbuf length which includes the Ethernet header
to the interface MTU is wrong.
The check was a little over the top so just remove it.
Approved by: mlaier (mentor)
MFC after: 3 days
enhance the security of bpf(4) by further relinquishing the privilege of
the bpf(4) consumer (assuming the ioctl commands are being implemented).
Once BIOCLOCK is executed, the device becomes locked which prevents the
execution of ioctl(2) commands which can change the underly parameters of the
bpf(4) device. An example might be the setting of bpf(4) filter programs or
attaching to different network interfaces.
BIOCSETWF can be used to set write filters for outgoing packets. Currently if
a bpf(4) consumer is compromised, the bpf(4) descriptor can essentially be used
as a raw socket, regardless of consumer's UID. Write filters give users the
ability to constrain which packets can be sent through the bpf(4) descriptor.
These features are currently implemented by a couple programs which came from
OpenBSD, such as the new dhclient and pflogd.
-Modify bpf_setf(9) to accept a "cmd" parameter. This will be used to specify
whether a read or write filter is to be set.
-Add a bpf(4) filter program as a parameter to bpf_movein(9) as we will run the
filter program on the mbuf data once we move the packet in from user-space.
-Rather than execute two uiomove operations, (one for the link header and the
other for the packet data), execute one and manually copy the linker header
into the sockaddr structure via bcopy.
-Restructure bpf_setf to compensate for write filters, as well as read.
-Adjust bpf(4) stats structures to include a bd_locked member.
It should be noted that the FreeBSD and OpenBSD implementations differ a bit in
the sense that we unconditionally enforce the lock, where OpenBSD enforces it
only if the calling credential is not root.
Idea from: OpenBSD
Reviewed by: mlaier
struct ifnet most of if_findindex() become a complex no-op. Remove it
and replace it with a corrected version of the four line for loop it
devolved to plus some error handling. This should probably be replaced
with subr_unit at some point.
Switch from checking ifaddr_byindex to ifnet_byindex when looking for
empty indexes. Since we're doing this from if_alloc/if_free, we can
only be sure that ifnet_byindex will be correct. This fixes panics when
loading the ef(4) module. The panics were caused by the fact that
if_alloc was called four time before if_attach was called and thus
ifaddr_byindex was not set and the same unit was allocated again. This
in turn caused the first if_attach to fail because the ifp was not the
one in ifnet_byindex(ifp->if_index).
Reported by: "Wojciech A. Koszek" <dunstan at freebsd dot czest dot pl>
PR: kern/84987
MFC After: 1 day
- Add a note that additions should be made to if_free_type and not
if_free to help avoid this in the future.
This apparently fixes a use after free in if_bridge and may fix bugs
in other direct if_free_type consumers.
Reported by: thompsa
could initialise while unlocked if the bridge is not up when setting the inet
address, ether_ioctl() would call bridge_init.
Change it so bridge_init is always called unlocked and then locks before
calling bstp_initialization().
Reported by: Michal Mertl
Approved by: mlaier (mentor)
MFC after: 3 days
could initialise while unlocked if the bridge is not up when setting the inet
address, ether_ioctl() would call bridge_init.
Change it so bridge_init is always called unlocked and then locks before
calling bstp_initialization().
Reported by: Michal Mertl
Approved by: mlaier (mentor)
MFC after: 3 days
- rt0 passed to rt_check() must not be NULL, assert this.
- rt returned by rt_check() must be valid locked rtentry,
if no error occured.
o Modify callers, so that they never pass NULL rt0
to rt_check().
Reviewed by: sam, ume (nd6.c)
device driver, owned by the network stack, or initialized by the device
driver before attach and read-only from then on.
Not all device drivers and network stack components currently follow
these rules, especially with respect to IFF_UP, and a few exceptions
with IFF_ALLMULTI.
MFC after: 7 days
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
and move both flags from ifnet.if_flags to ifnet.if_drv_flags, making
and documenting the locking of these flags the responsibility of the
device driver, not the network stack. The flags for these two fields
will be mutually exclusive so that they can be exposed to user space as
though they were stored in the same variable.
Provide #defines to provide the old names #ifndef _KERNEL, so that user
applications (such as ifconfig) can use the old flag names. Using the
old names in a device driver will result in a compile error in order to
help device driver writers adopt the new model.
When exposing the interface flags to user space, via interface ioctls
or routing sockets, or the two fields together. Since the driver flags
cannot currently be set for user space, no new logic is currently
required to handle this case.
Add some assertions that general purpose network stack routines, such
as if_setflags(), are not improperly used on driver-owned flags.
With this change, a large number of very minor network stack races are
closed, subject to correct device driver locking. Most were likely
never triggered.
Driver sweep to follow; many thanks to pjd and bz for the line-by-line
review they gave this patch.
Reviewed by: pjd, bz
MFC after: 7 days
m_copym(m, 0, M_COPYALL, how).
This is required for strict alignment architectures where we align the IP
header in the input path but m_copym() will create an unaligned copy in
bridge_broadcast(). m_copypacket() preserves alignment of the first mbuf.
Noticed by: Petri Simolin
Approved by: mlaier (mentor)
MFC after: 3 days
event handler, dev_clone, which accepts a credential argument.
Implementors of the event can ignore it if they're not interested,
and most do. This avoids having multiple event handler types and
fall-back/precedence logic in devfs.
This changes the kernel API for /dev cloning, and may affect third
party packages containg cloning kernel modules.
Requested by: phk
MFC after: 3 days
if_attach(). This allows ethernet drivers to use it in their routines
to program their MAC filters before ether_ifattach() is called (de(4) is
one such driver). Also, the if_addr mutex is destroyed in if_free()
rather than if_detach(), so there was another potential bug in that a
driver that failed during attach and called if_free() without having
called ether_ifattach() would have tried to destroy an uninitialized mutex.
Reported by: Holm Tiffe holm at freibergnet dot de
Discussed with: rwatson
using ifp->if_addr_mtx:
- Initialize if_addr_mtx when ifnet is initialized.
- Destroy if_addr_mtx when ifnet is torn down.
- Rename ifmaof_ifpforaddr() to if_findmulti(); assert if_addr_mtx.
Staticize.
- Extract ifmultiaddr allocation and initialization into if_allocmulti();
accept a 'mflags' argument to indicate whether or not sleeping is
permitted. This centralizes error handling and address duplication.
- Extract ifmultiaddr tear-down and deallocation in if_freemulti().
- Re-structure if_addmulti() to hold if_addr_mtx around manipulation of
the ifnet multicast address list and reference count manipulation.
Make use of non-sleeping allocations. Annotate the fact that we only
generate routing socket events for explicit address addition, not
implicit link layer address addition.
- Re-structure if_delmulti() to hold if_addr_mtx around manipulation of
the ifnet multicast address list and reference count manipulation.
Annotate the lack of a routing socket event for implicit link layer
address removal.
- De-spl all and sundry.
Problem reported by: Ed Maste <emaste at phaedrus dot sandvine dot ca>
MFC after: 1 week
ifp->if_resolvemulti(), do so with M_NOWAIT rather than M_WAITOK, so
that a mutex can be held over the call. In the FDDI code, add a
missing M_ZERO. Consumers are already aware that if_resolvemulti()
can fail.
MFC after: 1 week
lists. Add accessor macros.
This changes the size of struct ifnet, but ideally, all ifnet consumers
are now using if_alloc() to allocate these structures rather than
embedding them into device driver softc's, so this won't modify the
network device driver ABI.
MFC after: 1 week
FreeBSD specific ip_newid() changes NetBSD does not have.
Correct handling of non AF_INET packets passed to bpf [2].
PR: kern/80340[1], NetBSD PRs 29150[1], 30844[2]
Obtained from: NetBSD ip_gre.c rev. 1.34,1.35, if_gre.c rev. 1.56
Submitted by: Gert Doering <gert at greenie.muc.de>[2]
MFC after: 4 days
temporary buffer then pass the array to user-space once we have
dropped the lock.
While we are here, drop an assertion which could result in a
kernel panic under certain race conditions.
Pointed out by: rwatson
- most of the kernel code will not care about the actual encoding of
scope zone IDs and won't touch "s6_addr16[1]" directly.
- similarly, most of the kernel code will not care about link-local
scoped addresses as a special case.
- scope boundary check will be stricter. For example, the current
*BSD code allows a packet with src=::1 and dst=(some global IPv6
address) to be sent outside of the node, if the application do:
s = socket(AF_INET6);
bind(s, "::1");
sendto(s, some_global_IPv6_addr);
This is clearly wrong, since ::1 is only meaningful within a single
node, but the current implementation of the *BSD kernel cannot
reject this attempt.
Submitted by: JINMEI Tatuya <jinmei__at__isl.rdc.toshiba.co.jp>
Obtained from: KAME
bridge but the interface can still be changed afterwards.
This falls under the 'dont do that' category but log an warning when INVARIANTS
is defined.
Approved by: mlaier (mentor)
MFC after: 3 days
be used to pass statistics regarding dropped, matched and received
packet counts from the kernel to user-space. While we are here
introduce a new counter for filtered or matched packets. We currently
keep track of packets received or dropped by the bpf device, but not
how many packets actually matched the bpf filter.
-Introduce net.bpf.stats sysctl OID
-Move sysctl variables after the function prototypes so we can
reference bpf_stats_sysctl(9) without build errors.
-Introduce bpf descriptor counter which is used mainly for sizing
of the xbpf_d array.
-Introduce a xbpf_d structure which will act as an external
representation of the bpf_d structure.
-Add a the following members to the bpfd structure:
bd_fcount - Number of packets which matched bpf filter
bd_pid - PID which opened the bpf device
bd_pcomm - Process name which opened the device.
It should be noted that it's possible that the process which opened
the device could be long gone at the time of stats collection. An
example might be a process that opens the bpf device forks then exits
leaving the child process with the bpf fd.
Reviewed by: mdodd
which in the future will hold IFF_OACTIVE and IFF_RUNNING, and have
its access synchronized by the device driver rather than the
protocol stack. This will avoid potential races in the management
of flags in if_flags.
Discussed with: various (scottl, jhb, ...)
MFC after: 1 week
Compare pointers with NULL rather than treating them as booleans.
Compare pointers with NULL rather than 0 to make it more clear
they are pointers.
Assign pointers value of NULL rather than 0 to make it more clear
they are pointers.
MFC after: 3 days
- Introduce a subsystem mutex, natm_mtx, manipulated with accessor macros
NATM_LOCK_INIT(), NATM_LOCK(), NATM_UNLOCK(), NATM_LOCK_ASSERT(). It
protects the consistency of pcb-related data structures. Finer grained
locking is possible, but should be done in the context of specific
measurements (as very little work is done in netnatm -- most is in the
ATM device driver or socket layer, so there's probably not much
contention).
- Remove GIANT_REQUIRED, mark as NETISR_MPSAFE, remove
NET_NEEDS_GIANT("netnatm").
- Conditionally acquire Giant when entering network interfaces for
ifp->if_ioctl() using IFF_LOCKGIANT(ifp)/IFF_UNLOCKGIANT(ifp) in order
to coexist with non-MPSAFE atm ifnet drivers..
- De-spl.
MFC after: 2 weeks
Reviewed by: harti, bms (various versions)
the case of an RTM_CHANGE was specific, i.e. that it matched completely. This
led to a route change of a non-existent route changing the default route
as the radix code would simply back track to that point and hand that
route back to the routing socket code.
PR: 82974
Reviewed by: Tai-hwa Liang <avatar@mmlab.cse.yzu.edu.tw>
Ben Kaduk <minimarmot@gmail.com>
Bjoern A. Zeeb <bzeeb-lists@lists.zabbadoz.net>
Obtained from: OpenBSD with modifications.
MFC after: 2 weeks
Some of the (IPv6) cleanup functions send packets to inform peers of the
departure. These packets confused users of ifnet_departure_event (pf at the
moment).
PR: kern/80627
Tested by: Divacky Roman
MFC after: 1 week
- Introduce a helper function if_setflag() containing the code common
to ifpromisc() and if_allmulti() instead of duplicating the code poorly,
with different bugs.
- Call ifp->if_ioctl() in a consistent way: always use more compatible C
syntax and check whether ifp->if_ioctl is not NULL prior to the call.
MFC after: 1 month
we can only bridge interfaces with the same value it meant that all members had
to be set at ETHERMTU as well.
Allow the first member to be added to define the MTU for the bridge, the check
still applies to all additional members.
Print an informative message if the MTU is incorrect [1]
Requested by: Niki Denev [1]
Approved by: mlaier (mentor)
MFC after: 3 days
hooks for each outgoing interface but also run pfil hooks _N times_ on the
bridge interface. This is changed so pfil hooks are run once for the bridge
interface (bridge0) and then only on the outgoing interfaces in the broadcast
loop.
- Simplify bridge_enqueue() by moving bridge_pfil() to the callers.
- Check (inet6_pfil_hook.ph_busy_count >= 0), it may be possible to have a
packet filter hooked for only ipv6 but we were only checking if ipv4 hooks
were busy.
- Minor optimisation for null mbuf check after bridge_pfil(), move it into the
if-block as it couldnt possibly be null outside.
Prodded by: mlaier
Approved by: re (scottl), mlaier (mentor)
redundant with respect to existing mbuf copy label routines. Expose
a new mac_copy_mbuf() routine at the top end of the Framework and
use that; use the existing mpo_copy_mbuf_label() routine on the
bottom end.
Obtained from: TrustedBSD Project
Sponsored by: SPARTA, SPAWAR
Approved by: re (scottl)
packet filter. This would cause a panic on architectures that require strict
alignment such as sparc64, ia64 and ppc.
This uses the code block from if_bridge and the newly added macro
IP_HDR_ALIGNED_P().
This /might/ be a temporary messure before all NIC drivers are educated
to align the header themself.
PR: ia64/81284
Obtained from: NetBSD (if_bridge)
Approved by: re (dwhite), mlaier (mentor)
packet filter. This would cause a panic on architectures that require strict
alignment such as sparc64 (tier1) and ia64/ppc (tier2).
This adds two new macros that check the alignment, these are compile time
dependent on __NO_STRICT_ALIGNMENT which is set for i386 and amd64 where
alignment isn't need so the cost is avoided.
IP_HDR_ALIGNED_P()
IP6_HDR_ALIGNED_P()
Move bridge_ip_checkbasic()/bridge_ip6_checkbasic() up so that the alignment
is checked for ipfw and dummynet too.
PR: ia64/81284
Obtained from: NetBSD
Approved by: re (dwhite), mlaier (mentor)
- Introducing the possibility of using locks different than mutexes
for the knlist locking. In order to do this, we add three arguments to
knlist_init() to specify the functions to use to lock, unlock and
check if the lock is owned. If these arguments are NULL, we assume
mtx_lock, mtx_unlock and mtx_owned, respectively.
- Using the vnode lock for the knlist locking, when doing kqueue operations
on a vnode. This way, we don't have to lock the vnode while holding a
mutex, in filt_vfsread.
Reviewed by: jmg
Approved by: re (scottl), scottl (mentor override)
Pointyhat to: ssouhlal
Will be happy: everyone
a cosmetic change. m_uiotombuf() produces a packet header mbuf, while
original implementation did not. When kernel is compiled with MAC
support, headerless mbuf will cause panic.
Reported by: Alexander Nikiforenko <asn rambler-co.ru>
Approved by: re (scottl)
MFC After: 2 weeks
route itself.
It fixes a bug where an IPv4 route for example has an IPv6 gateway
specified:
route add 10.1.1.1 -inet6 fe80::1%fxp0
Destination Gateway Flags Refs Use Netif Expire
10.1.1.1 fe80::1%fxp0 UGHS 0 0 fxp0
The fix rejects these illegal combinations:
route: writing to routing socket: Invalid argument
add host 10.1.1.1: gateway fe80::1%fxp0: Invalid argument
Reviewed by: KAME jinmei@isl.rdc.toshiba.co.jp
Reviewed by: andre (mentor)
Approved by: re
MFC after: 5
pointer to a softc which is no longer valid since the ifnet struct was split
out from the softc.
Approved by: mlaier (mentor)
Approved by: re (blanket)
a DLT_NULL interface. In particular:
1) Consistently use type u_int32_t for the header of a
DLT_NULL device - it continues to represent the address
family as always.
2) In the DLT_NULL case get bpf_movein to store the u_int32_t
in a sockaddr rather than in the mbuf, to be consistent
with all the DLT types.
3) Consequently fix a bug in bpf_movein/bpfwrite which
only permitted packets up to 4 bytes less than the MTU
to be written.
4) Fix all DLT_NULL devices to have the code required to
allow writing to their bpf devices.
5) Move the code to allow writing to if_lo from if_simloop
to looutput, because it only applies to DLT_NULL devices
but was being applied to other devices that use if_simloop
possibly incorrectly.
PR: 82157
Submitted by: Matthew Luckie <mjl@luckie.org.nz>
Approved by: re (scottl)
fails.
Move detaching the ifnet from the ifindex_table into if_free so we can
both keep the sanity checks and actually delete the ifnets. [0]
Reported by: gallatin [0]
Approved by: re (blanket)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
using the layer2, mac and mac-type keywords.
This is one of the last features that bridge.c has over if_bridge and gets us
very close to a full functional replacement.
Approved by: mlaier (mentor)
coded at 512 (BPF_MAXINSNS) to being tunable. This is useful for users
who wish to use complex or large bpf programs when filtering traffic.
For now we will default it to BPF_MAXINSNS. I have tested bpf programs
with well over 21,000 instructions without any problems.
Discussed with: phk
spanning tree support.
Based on Jason Wright's bridge driver from OpenBSD, and modified by Jason R.
Thorpe in NetBSD.
Reviewed by: mlaier, bms, green
Silence from: -net
Approved by: mlaier (mentor)
Obtained from: NetBSD
so if_tap doesn't need to rely on locally-rolled code to do same.
The observable symptom of if_tap's bzero'ing the address details
was a crash in "ifconfig tap0" after an if_tap device was closed.
Reported By: Matti Saarinen (mjsaarin at cc dot helsinki dot fi)
1. Copy a NULL-terminated string into a fixed-length buffer, and
2. copyout that buffer to userland,
we really ought to
0. Zero the entire buffer
first.
Security: FreeBSD-SA-05:08.kmem
to the mbuf. Offset cannot exceed MHLEN bytes. This is currently used to
fix Ethernet header alignment problem on alpha and sparc64. Also change all
users of m_uiotombuf to pass proper offset.
Reviewed by: jmg, sam
Tested by: Sten Spans "sten AT blinkenlights DOT nl"
MFC after: 1 week
debug.bpf_bufsize is now net.bpf.bufsize
debug.bpf_maxbufsize is now net.bpf.maxbufsize
-move function prototypes for bpf_drvinit and bpf_clone up to the
top of the file with the others
-assert bpfd lock in catchpacket() and bpf_wakeup()
MFC after: 2 weeks
a taskqueue(9) task. This fixes LORs and adds possibility
to serve such events pseudorecursively, when link state
change of interface causes subsequent change on other
interfaces.
Sponsored by: Rambler
Reviewed by: sam, brooks, mux
results in connectivty to MacOSX hosts via fwip.
Thanks to Apple's Arulchandran Paramasivam <arulchandranp@apple.com> for
letting us know what we were doing wrong.
Reviewed by: dfr
MFC After: 7 days
them all, otherwise the driver will be useless and will only confuse user
as manual page says nothing about the need to enable one of those frame
types explicitly in the kernel config.
PR: kern/47152
Submitted by: Andriy Gapon <avg@icyb.net.ua>
MFC after: 3 days
attempting to change the BPF filter on a BPF descriptor at the same
time: retrieve the old filter pointer under the same locked region
as setting the new pointer.
MFC after: 3 days
clock time to uptime because wall clock time may go backwards.
This is a change in the API which will impact SNMP agents who are using
ifi_epoch to set RFC2233's ifCounterDiscontinuityTime. None are know to
exist today. This will not impact applications that are using the
<index, epoch> tuple to verify interface uniqueness except that it
eliminates a race which could lead to a false assumption of uniqueness.
Because this is a behavior change, bump __FreeBSD_version.
Discussed with: re (jhb, scottl)
MFC after: 3 days
Pointed out by: pkh (way back at EuroBSDCon)
Pointy hat: brooks
panic at kmem_alloc() via malloc(9).
PR: kern/77748
Submitted by: Wojciech A. Koszek
OK'ed by: brooks
Security: local DoS, a sample code in the PR.
MFC after: 3 days
hosts to share an IP address, providing high availability and load
balancing.
Original work on CARP done by Michael Shalayeff, with many
additions by Marco Pfatschbacher and Ryan McBride.
FreeBSD port done solely by Max Laier.
Patch by: mlaier
Obtained from: OpenBSD (mickey, mcbride)
a packet has VLAN mbuf tag attached. This is faster to check than
m_tag_locate(), and allows us to use the tags in non-vlan(4) VLAN
producers.
The first argument to VLAN_OUTPUT_TAG() is now unused but retained
for backward compatibility.
While here, embellish a fix in rev. 1.174 of if_ethersubr.c -- it
now checks for packets with VLAN (mbuf) tags, and it should now
be possible to bridge(4) on vlan(4)'s whose parent interfaces
support VLAN decapsulation in hardware.
Reviewed by: sam
driver did VLAN decapsulation in hardware, we were passing a frame
as if it came for the parent (non-VLAN) interface. Stop this from
happening.
Reminded by: glebius
Security: This could pose a security risk in some setups
which will finally lead to kernel panic.
Security: This prevents a local (root-launched) DoS
Submitted by: Wojciech A. Koszek [dunstan at freebsd czest pl]
PR: 77421
MFC After: 1 week
- ip_fw_chk() returns action as function return value. Field retval is
removed from args structure. Action is not flag any more. It is one
of integer constants.
- Any action-specific cookies are returned either in new "cookie" field
in args structure (dummynet, future netgraph glue), or in mbuf tag
attached to packet (divert, tee, some future action).
o Convert parsing of return value from ip_fw_chk() in ipfw_check_{in,out}()
to a switch structure, so that the functions are more readable, and a future
actions can be added with less modifications.
Approved by: andre
MFC after: 2 months
- Introduce another ng_ether(4) callback ng_ether_link_state_p, which
is called from if_link_state_change(), every time link is changed.
- In ng_ether_link_state() send netgraph control message notifying
of link state change to a node connected to "lower" hook.
Reviewed by: sam
MFC after: 2 weeks
Silence on: net@, current@, hackers@.
No objections: joerg
Requested by: by many (mostly Cronyx) users for a long long time.
MFC after: 10 days
PR: kern/21771, kern/66348
