and not 8-bit. Fix support for isochronous transfers in USB host mode.
Fix a whitespace while at it.
MFC after: 1 week
Reported by: SAITOU Toshihide <toshi@ruby.ocn.ne.jp>
PR: usb/181987
routing if we get certain errors. Poll for command completion upon
command timeouts. The XHCI error events might not generate interrupts.
MFC after: 1 week
Reported by: Daniel Gerzo <danger@rulez.sk>, Antonis Anastasiadis <anastasiadis@datalive.gr>
PR: usb/181159
Approved by: re (gjb)
IMAN register to clear the pending interrupt status bits. This patch
tries to solve problems seen on the MacBook Air, as reported by
Johannes Lundberg <johannes@brilliantservice.co.jp>
MFC after: 1 week
The Block Event Interrupts, BEI, feature does not
work like expected with the Renesas XHCI chipsets.
Revert feature.
While at it correct the TD SIZE computation in
case of Zero Length Packet, ZLP, in the end of a
multi frame USB transfer.
MFC after: 1 week
PR: usb/180726
1) Only multi-TD isochronous transfers should use NORMAL
type after specific type as per XHCI specification.
2) BEI bit is only available in NORMAL and ISOCHRONOUS
TRB types. Don't use this bit for other types to avoid
hardware asserts. Reserved bits should be don't care
though ...
MFC after: 1 week
PR: usb/179342
the regular interrupt handler is not working properly or
in case of MSI interrupts which are not yet supported.
Remove interrupt setup code for FreeBSD versions older
than 700031.
MFC after: 1 week
PR: usb/179342
controller hardware most likely present on UHCI chipsets aswell. The
bug manifests itself when issuing isochronous transfers and bulk
transfers towards the same device simultaneously. From time to time it
happens that either the completion IRQ was missing or that the
completion IRQ was happening before the ITD/SITD was completely
written back to memory. The workaround assumes that double buffered
isochronous transfers are used, and that a second interrupt is
generated at the beginning of the next isochronous transfer to
complete the previous one. Possibly skipping the interrupt at the last
isochronous frame is possible, but will then break single buffered
isochronous transfers. For now we can live with some extra interrupts.
MFC after: 1 week
enumeration lock. Make sure all callers of usbd_enum_lock() check the return
value. Remove the control transfer specific lock. Bump the FreeBSD version
number, hence external USB modules may need to be recompiled due to a USB
device structure change.
MFC after: 1 week
into the FreeBSD boot loader, typically for non-USB aware BIOSes, EFI systems
or embedded platforms. This is also useful for out of the system compilation
of the FreeBSD USB stack for various purposes. The USB kernel files can
now optionally include a global header file which should include all needed
definitions required to compile the FreeBSD USB stack. When the global USB
header file is included, no other USB header files will be included by
default.
Add new file containing the USB stack configuration for the
FreeBSD loader build.
Replace some __FBSDID()'s by /* $FreeBSD$ */ comments. Now all
USB files follow the same style.
Use cases:
- console in loader via USB
- loading kernel via USB
Discussed with: Hiroki Sato, hrs @ EuroBSDCon
This patch will save CPU time when the XHCI interrupt is
shared with other devices.
Only check event rings when interrupt bits are set.
Otherwise would indicate hiding possible hardware fault(s).
Tested by: sos @
Submitted by: sos @
MFC after: 1 week
This brand of controllers expects that the number of
contexts specified in the input slot context points
to an active endpoint context, else it refuses to
operate.
- Ring the correct doorbell when streams mode is used.
- Wrap one or two long lines.
Tested by: Markus Pfeiffer (DragonFlyBSD)
MFC after: 1 week
DWC OTG driver. Fix a hang issue when using LOW and FULL speed
BULK traffic. Make sure we don't ask for data in the last
microframe. This allows using devices like USB mice and USB
keyboards connected to the RPI-B.
Suggested by: gonzo @
Also update the port reset time from 250ms to 50ms. Some USB devices
have a hard limit in hardware at 222ms for the port reset time and will
not enumerate unless this delay is closer to the usb.org defined value.
This patch can fix enumeration with some USB devices.
Tested by: Guido van Rooij
Submitted by: Nick Hibma
MFC after: 1 week
gone rule. Optimise use of channels so that when a channel
is not ready another channel is used. Instead of using the SOF interrupt
use the system timer to drive the host statemachine. This might
give lower throughput and higher latency, but reduces the CPU usage
significantly. The DWC OTG host mode support should not be considered
for serious USB host controller applications. Some problems are still
seen with LOW speed USB devices.
of the DWC OTG is very simple in PIO mode, and we need to re-transmit
data when NAK is received among other things. We probably will need
to implement some kind of rate limitation on the NAK-ing.
The DWC OTG host mode support should still be considered
experimental. Isochronous support for DWC OTG is not
fully implemented. Some code added derives from
Aleksandr Rybalko's dotg.c driver.
in SUPER-speed mode, USB 3.0.
This feature has not been tested yet, due to lack of hardware.
This feature is useful when implementing protocols like UASP,
USB attached SCSI which promises higher USB mass storage throughput.
This patch also implements support for hardware processing of endpoints
for increased performance. The switching to hardware processing
of an endpoint is done via a callback to the USB controller driver. The
stream feature is implemented like a variant of a hardware USB protocol.
USB controller drivers implementing device mode needs to be updated to
implement the new "xfer_stall" USB controller method and remove the
"xfer" argument from the "set_stall" method.
The API's toward existing USB drivers are preserved. To setup a USB transfer
in stream mode, set the "stream_id" field of the USB config structure to
the desired value.
The maximum number of BULK streams is currently hardcoded and limited to 8
via a define in usb_freebsd.h.
All USB drivers should be re-compiled after this change.
LibUSB will be updated next week to support streams mode. A new IOCTL to
setup BULK streams as already been implemented. The ugen device nodes
currently only supports stream ID zero.
The FreeBSD version has been bumped.
MFC after: 2 weeks
This will give you more bandwidth for isochronous
FULL speed applications connected through a
High Speed HUB.
This patch has been tested with XHCI and EHCI.
MFC after: 1 week
and not asynchronously. This fixes problems related to USB system
suspend and resume. It is assumed that we are always allowed to sleep
from the device_suspend() method.
MFC after: 1 week
Submitted by: jkim
Currently the code is not built by any modules. That will
be fixed later. The Atmel ARM bus interface file part of this
commit is just for sake of example. All registers and bits are
declared like macros and not C-structures like in official
Synopsis header files. This driver mostly origins from the
musb_otg.c driver in FreeBSD except that the chip specific
programming has been replaced by the one for DWC 2.0 USB OTG.
Some parts related to system suspend and resume have been left
like empty functions for the future. USB suspend and resume is
fully supported.
This patch should remove the need for kldunload of USB
controller drivers at suspend and kldload of USB controller
drivers at resume.
This patch also fixes some build issues in avr32dci.c
MFC after: 2 weeks
one. Interestingly, these are actually the default for quite some time
(bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
since r52045) but even recently added device drivers do this unnecessarily.
Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
Discussed with: jhb
- Also while at it, use __FBSDID.
- Make it easier to port the USB code to other platforms by only using
one set of memory functions for clearing and copying memory. None of
the memory copies are overlapping. This means using bcopy() is not
required.
- Fix a compile warning when USB_HAVE_BUSDMA=0
- Add missing semicolon in avr32dci.
- Update some comments.
MFC after: 1 week
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
