- add support for T3C
- add DDP support (zero-copy receive)
- fix TOE transmit of large requests
- fix shutdown so that sockets don't remain in CLOSING state indefinitely
- register listeners when an interface is brought up after tom is loaded
- fix setting of multicast filter
- enable link at device attach
- exit tick handler if shutdown is in progress
- add helper for logging TCB
- add sysctls for dumping transmit queues
- note that TOE wxill not be MFC'd until after 7.0 has been finalized
MFC after: 3 days
- Added loose RX MTU functionality to allow frames larger than 1500 bytes
to be accepted even though the interface MTU is set to 1500.
- Implemented new TCP header splitting/jumbo frame support which uses
two chains for receive traffic rather than the original single recevie
chain.
- Added additional debug support code.
legacy interrupts rather than MSI as a special case. Prior to this
commit, the interrupt handler was doing the slow handshaking with
the device to ensure the legacy interrupt was lowered in both
the legacy and MSI-X case. This handshaking was not
required for MSI-X.
allocator for jumbo frame.
o Removed unneeded jlist lock which was used to manage jumbo
buffers.
o Don't reinitialize hardware if MTU was not changed.
o Added additional check for minimal MTU size.
o Added a new tunable hw.skc.jumbo_disable to disable jumbo frame
support for the driver. The tunable could be set for systems that
do not need to use jumbo frames and it would save
(9K * number of Rx descriptors) bytes kernel memory.
o Jumbo buffer allocation failure is no longer critical error for
the operation of sk(4). If sk(4) encounter the allocation failure
it just disables jumbo frame support and continues to work without
user intervention.
With these changes jumbo frame performance of sk(4) was slightly
increased and users should not encounter jumbo buffer allocation
failure. Previously sk(4) tried to allocate physically contiguous
memory, 3388KB for 256 Rx descriptors. Sometimes that amount of
contiguous memory region could not be available for running systems
which in turn resulted in failure of loading the driver.
Tested by: Cy Schubert < Cy.Schubert () komquats dot com >
With write-allocate cache we get into the following scenario:
1. data has been updated in the memory by the USB HC, but
2. D-cache holds an un-flushed value of it
3. when affected cache line is being replaced, the old (un-flushed) value is
flushed and overwrites the newly arrived
This is possible due to how write-allocate works with virtual caches (ARM for
example).
In case of USB transfers it leads to fatal tags discrepancies in umass(4)
operation, which look like the following:
umass0: Invalid CSW: tag 1 should be 2
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 3
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 4
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 5
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): Retrying Command
umass0: Invalid CSW: tag 1 should be 6
(probe0:umass-sim0:0:0:0): Request completed with CAM_REQ_CMP_ERR
(probe0:umass-sim0:0:0:0): error 5
(probe0:umass-sim0:0:0:0): Retries Exausted
To eliminate this, a BUS_DMASYNC_PREREAD sync operation is required in
usbd_start_transfer().
Credits for nailing this down go to Grzegorz Bernacki gjb AT semihalf DOT com.
Reviewed by: imp
Approved by: cognet (mentor)
- Include lock.h in lockmgr.h as nested header in order to safely use
LOCK_FILE and LOCK_LINE. As long as this code will be replaced soon
we can tollerate for a while this namespace pollution even if the real
fix would be to let lockmgr() depend by lock.h as a separate header.
NOP-message polling in ciss_periodic().
Note that setting the tunable to non-zero can be workaround only for
`ADAPTER HEARTBEAT FAILED' problem, and may freeze the system w/o
the problem.
Reviewed by: scottl
Reported by: Attila Nagy
MFC after: 3 days
- Rename rt2560_read_eeprom to rt2560_read_config, we already have
rt2560_eeprom_read
- If hardware gives us wrong encryption done index, shout out loudly and
terminate the processing loop
- Process encryption done if RX done bit is set in interrupt status register
(according to Ralink Linux driver)
- Turn VALID/BUSY bits in TX descriptor only after TX descriptor is fully setup
- Fix BBP read: RT2560_BBPCSR can't be written until its RT2560_BBP_BUSY bit is
off (according to Ralink Linux driver)
- Skip invalid (0 of 0xffff) BBP register/value entries stored in EEPROM
- Fix channel TX power location in EEPROM, if channel TX power is above 31 set
it to 24 (TX power only has 5bits in RF register, "24" is according to Ralink
Linux driver)
- Configure BBP according to the BBP register/value stored in EEPROM, restore
BBP17 (RX sensitivity tuning) to default value after this.
- Set TX/RX antenna after BBP is initialized; these two operation will try to
set BBP registers
- Reconfigure ACK TX time registers according to 802.11g standard (TX @36Mb,
other side's ACK should be sent @24Mb).
- 2560 parts have two TX ring: one for management/control packets, one for data
packets. Add private OACTIVE flag for each of them. Turn on IFF_DRV_OACTIVE
if one of private OACTIVE is on; turn off IFF_DRV_OACTIVE iff all of them are
off.
- Rework watchdog to mimic old if_watchdog action. Process TX done/encryption
done in watchdog function (according to Ralink Linux driver)
Obtained from: DragonFly
Approved by: sam (mentor)
Tested by: sam
Related to PR: kern/117655
# Forcing long slot time setting is not included in this commit, comment and
# related code is in place, so if problem pops up, quick tests could be done.
down some DCMD's without any data. Thanks to Dell and LSI for helping
to provide clues to figure out this problem. Now MegaCli can upgrade
the firmware and should work identical when run on Linux.
Reviewed by: scottl, LSI
MFC after: 1 day
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
free function controlable, instead of passing the KVA of the buffer
storage as the first argument.
Fix all conventional users of the API to pass the KVA of the buffer
as the first argument, to make this a no-op commit.
Likely break the only non-convetional user of the API, after informing
the relevant committer.
Update the mbuf(9) manual page, which was already out of sync on
this point.
Bump __FreeBSD_version to 800016 as there is no way to tell how
many arguments a CPP macro needs any other way.
This paves the way for giving sendfile(9) a way to wait for the
passed storage to have been accessed before returning.
This does not affect the memory layout or size of mbufs.
Parental oversight by: sam and rwatson.
No MFC is anticipated.
o conversion to callout(9) API.
o add a missing driver lock in bfe_ifmedia_sts().
o use our callout to drive watchdog timer.
o restart Tx routine if pending queued packets are present in
watchdog handler.
o unarm watchdog timer only if there are no queued packets.
o don't blindly reset phy and let phy driver handle link change
request in bfe_init_locked().
o return the status of mii_mediachg() to caller in
bfe_ifmedia_upd(). Previously it always returned 0 to caller.
o add check for IFF_DRV_RUNNING flag as well as IFF_DRV_OACTIVE
in bfe_start_locked().
o implement miibus_statchg method that keeps track of current
link state changes as well as negotiated speed/duplex/
flow-control configuration.
Reprogram MAC to appropriate duplex state. Flow-control
configuration was also implemented but commented out at the
moment. The flow-control configuration will be enabled again
after we have general flow-control framework in mii layer.
Reported by: Yousif Hassan < yousif () alumni ! jmu ! edu >
Tesdted by: Yousif Hassan < yousif () alumni ! jmu ! edu >
- Fix whitespace according to style(9).
- Sync the comment describing why we have to wait in nsphy_reset()
with nsphyter_reset(). It's true that the manual tells to not do a
reset within 500us of applying power but that's unlikely the cause
of problems seen here. Generally having to wait 500us after a reset
however is.
DP83847 PHYs. The main reason for using a specific driver for these
PHYs are reset quirks similar to the nsphy(4) driven DP83840A.
PR: 112654
Obtained from: NetBSD
MFC after: 2 weeks
Thanks to: mlaier for testing w/ DP83815
- Remove the "thread" argument from the lockmgr() function as it is
always curthread now
- Axe lockcount() function as it is no longer used
- Axe LOCKMGR_ASSERT() as it is bogus really and no currently used.
Hopefully this will be soonly replaced by something suitable for it.
- Remove the prototype for dumplockinfo() as the function is no longer
present
Addictionally:
- Introduce a KASSERT() in lockstatus() in order to let it accept only
curthread or NULL as they should only be passed
- Do a little bit of style(9) cleanup on lockmgr.h
KPI results heavilly broken by this change, so manpages and
FreeBSD_version will be modified accordingly by further commits.
Tested by: matteo
- Improve error handling for load operations.
- Fix a memory corruption bug when using certain linux management apps.
- Allocate all commands up front to avoid OOM deadlocks later on.
