seeing SPIORDY and checking for PHASEMIS. My last change turned out to
be less cosmetic then I thought.
Pointed out by: Satoshi Asami <asami@cs.berkeley.edu>,
Faried Nawaz <fn@pain.csrv.uidaho.edu
NetBSD/OpenBSD support Submitted by:Noriyuki Soda <soda@sra.co.jp>,
Pete Bentley <pete@demon.net>,
Charles M. Hannum <mycroft@mit.edu>,
Theo de Raadt <deraadt@theos.com>
Add a panic for attempts to page in a non paged out SCB.
Re-order some of the interrupt routine for better performance.
NetBSD/OpenBSD support Submitted by:Noriyuki Soda <soda@sra.co.jp>,
Pete Bentley <pete@demon.net>,
Charles M. Hannum <mycroft@mit.edu>,
Theo de Raadt <deraadt@theos.com>
Cosmetic change to p_mesgout code so that it "looks" the same as what
is done in the inb* routines.
NetBSD/OpenBSD support Submitted by:Noriyuki Soda <soda@sra.co.jp>,
Pete Bentley <pete@demon.net>,
Charles M. Hannum <mycroft@mit.edu>,
Theo de Raadt <deraadt@theos.com>
case where blocking can occur, thereby giving other process's a chance
to modify the queue where a page resides. This could cause numerous
process and system failures.
that the datastructures needed to support the swap pager can take
enough space to fully deplete system memory, and cause a deadlock.
This change keeps large objects from being filled with dirty pages
without the appropriate swap pager datastructures. Right now,
default objects greater than 1/4 the size of available system memory
are converted to swap objects, thereby eliminating the risk of deadlock.
phasemiss to sneak by without detection. This should fix the
Wide/Narrow boot problems that have been reported since this bug
caused the driver ignore a narrow target rejecting wide negotiation.
a condition when blocking can occur, and the daemon did not check properly
for a page remaining on the expected queue. Additionally, the inactive
target was being set much too large for small memory machines. It is now
being calculated based upon the amount of user memory available on every
pageout daemon run. Another problem was that if memory was very low, the
pageout daemon could fail repeatedly to traverse the inactive queue.
problem. BY MISTAKE, the vm_page_unqueue (or equiv) was removed from the
vm_fault code. Really bad things appear to happen if a page is on a queue
while it is being faulted.
(returns EPERM always, the errno is specified by POSIX).
If you really have a desperate need to link or unlink a directory, you
can use fsdb. :-)
This should stop any chance of ftpd, rdist, "rm -rf", etc from
bugging out and damaging the filesystem structure or loosing races
with malicious users.
Reviewed by: davidg, bde
Kernel Appletalk protocol support
both CAP and netatalk can make use of this..
still needs some owrk but it seemd the right tiime to commit it
so other can experiment.
guru out there can find a way to take advantage of little-endianness to
make this computation more efficient. (I am certain that it can be done,
but haven't managed to make it work myself.)
unconventionally:
If COMPAT_IPFW is not defined, or if it is defined to 1, enable;
otherwise, disable.
This means that these changes actually have no effect on anyone at the
moment. (It just makes it easier for me to keep my code in sync.)
In the future, the `not defined' part of the hack should be eliminated,
but doing this now would require everyone to change their config files.
The same conditionals need to be made in ip_input.c as well for this to
ave any useful effect, but I'm not ready to do that right now.
call of ahc_scsirate. Otherwise, the proper setting may not get set until
the next reconnection/selection.
The saved_queue used to re-order the QINFIFO during error recovery or
certain SCB paging operations should be an array of u_chars not ints.
saved_queue type error pointed out by: Noriyuki Soda <soda@sra.co.jp>
comparing the PTD pointers, they needed to be masked by PG_FRAME, and
they weren't. Also, the "improved" non-386 code wasn't really an
improvement, so I simplified and fixed the code. This might have
caused some of the panics caused by the VM megacommit.
I spent the better part of a day trying to figure out why my
experiment didn't work the way I expected, only to find out that
the router was dropping huge numbers of packets because of PCI bus
priblems. This does not fix the bug that errors are counted as
input packets because my patch doesn't apply cleanly.
to use the full range of settings from 3.6-20MHz on any target.
Remove all Ultra settings except for the top three that are documented
to work. This fixes some problem reports with the last revision of the
driver since at least the 5.7MHz entry doesn't work in Ultra mode.
With this fix from Stephen, we are getting the target fork performance
that I have been trying to attain: P5-166, before the mega-commit: 700-800usecs,
after: 600usecs, with Stephen's fix: 500usecs!!! Also, this could be the
solution of some strange panic problems...
Reviewed by: dyson@freebsd.org
Submitted by: Stephen McKay <syssgm@devetir.qld.gov.au>
snuck in accidentally from the DARTNet kernel. SIOC*RTINFO were an
extended interface to the stock routing table and SIOCGETVIFINF was
an interface for rsvpd to ask the kernel for the list of multicast vif's.
Pointed-out-by: Brian Reichert <reichert@internet.com>
is enabled by having an "device ed0 at isa? [...]" config line.
The first PCI card will get a unit number one higher than the highest
defined for any ISA card of the ED type, e.g. if ed0 and ed1 are
configured, then the PCI cards will be ed2, ed3, ...
BEWARE: If you have configured your kernel as ed0 with the port address
as assigned by the PCI BIOS, then your card will be found by both the
PCI and ISA probes, and bad things may happen. Make sure to restore
the original port address form the GENERIC kernel for the ed0 device!
Reviewed by: davidg
