enabled.
The legacy (pre-802.11n) hardware doesn't support this - although
the AR5212 era hardware supports MRR, it doesn't have all the bits
needed to support MRR + RTS/CTS. The AR5416 and later support
a packet duration and RTS/CTS flags per rate scenario, so we should
support it.
Tested:
* AR9280, STA
PR: kern/170302
code is called and remove it from ath_buf_set_rate().
For the legacy (non-11n API) TX routines, ath_hal_filltxdesc() takes care
of setting up the intermediary and final descriptors right, complete
with copying the rate control info into the final descriptor so the
rate modules can grab it.
The 11n version doesn't do this - ath_hal_chaintxdesc() doesn't
copy the rate control bits over, nor does it clear isaggr/moreaggr/
pad delimiters. So the call to setuplasttxdesc() is needed here.
So:
* legacy NICs - never call the 11n rate control stuff, so filltxdesc
copies the rate control info right;
* 11n NICs transmitting legacy or 11n non-aggregate frames -
ath_hal_set11nratescenario() is called to setup rate control and
then ath_hal_filltxdesc() chains them together - so the rate control
info is right;
* 11n aggregate frames - set11nratescenario() is called, then
ath_hal_chaintxdesc() is called to chain a list of aggregate and subframes
together. This requires a call to ath_hal_setuplasttxdesc() to complete
things.
Tested:
* AR9280 in station mode
TODO:
* I really should make sure that the descriptor contents get blanked
out correctly or garbage left over from aggregate frames may show
up in non-aggregate frames, leading to badness.
functions, for both legacy and 802.11n.
This will simplify supporting the EDMA chipsets as these two descriptor
setup functions can just be overridden in their entirety, hiding all of
the subtle differences in setting things up.
It's not a permanent solution, as eventually the AR5416 HAL should grow
similar versions of the 11n descriptor functions and then those can be
used.
TODO:
* Push the "clr11naggr" call into the legacy setds, just to ensure
that retried frames don't end up with the aggregate bits set
inappropriately;
* Remove the "setlasttxdesc" call from the 11n TX path and push it
into setds_11n.
* Ensure that setds_11n will work correctly for non-aggregate frames;
* .. and then when it does, just unconditionally call "setds_11n" for
11n NICs and "setds" for non-11n NICs.
These (and a few others) will differ based on the underlying DMA
implementation.
For the EDMA NICs, simply stub them out in a fashion which will let
me focus on implementing the necessary descriptor API changes.
The correct ordering for non-aggregate TX is:
* call ath_hal_setuptxdesc() to setup the first TX descriptor complete
with the first TX rate/try count;
* call ath_hal_setupxtxdesc() to setup the multi-rate retry;
* .. or for 802.11n NICs, call ath_hal_set11nratescenario() for MRR and
802.11n flags;
* then call ath_hal_filltxdesc() to setup intermediary descriptors
in a multi-descriptor single frame.
The call to ath_hal_filltxdesc() routines seem to correctly (consistently?)
handle the intermediary descriptor flags, including copying the rate
control information to the final descriptor in the frame. That's used
by the rate control module rather than the hardware.
Tested:
* Only on AR9280 STA mode, however it should work on other chips in
both STA and AP mode.
wrapping.
The previous code was only wrapping descriptor "block" boundaries rather
than individual descriptors. It sounds equivalent but it isn't.
r238824 changed the descriptor allocation to enforce that an individual
descriptor doesn't wrap a 4KiB boundary rather than the whole block
of descriptors. Eg, for TX descriptors, they're allocated in blocks
of 10 descriptors for each ath_buf (for scatter/gather DMA.)
The existing method for testing for MRR is to call the "SetupXTXDesc"
HAL method and see if it returns AH_TRUE or AH_FALSE. This capability
explicitly lists what number of multi-rate attempts are possible.
"1" means "one rate attempt supported".
* shuffle things around so things fall on natural padding boundaries;
* add a couple of new flags to specify LDPC and whether to switch to the
low power RX chain configuration after this TX has completed.
Obtained from: Qualcomm Atheros
Specifically, however:
* AR9280 and later support 1-stream STBC RX;
* AR9280 and AR9287 support 1-stream STBC TX.
The STBC support isn't announced (yet) via net80211 and it isn't at all
chosen by the rate control code, so there's no real consumer of this
yet.
Obtained from: Qualcomm Atheros
(future) TPC support in the AR9300 HAL.
This is effectively a no-op for the moment as (a) TPC isn't really
supported, (b) the AR9300 HAL isn't yet public, and (c) the existing
HAL code doesn't use these fields.
Obtained from: Qualcomm Atheros
buffers.
ath_descdma is now being used for things other than the classical
combination of ath_buf + ath_desc allocations. In this particular case,
don't try to free and blank out the ath_buf list if it's not passed in.
of buffers, only the number of descriptors.
This involves:
* Change the allocation function to not use nbuf at all;
* When calling it, pass in "nbuf * ndesc" to correctly update how many
descriptors are being allocated.
Whilst here, fix the descriptor allocation code to correctly allocate
a larger buffer size if the Merlin 4KB WAR is required. It overallocates
descriptors when allocating a block that doesn't ever have a 4KB boundary
being crossed, but that can be fixed at a later stage.
The AR9300 and later descriptors are 128 bytes, however I'd like to make
sure that isn't used for earlier chips.
* Populate the TX descriptor length field in the softc with
sizeof(ath_desc)
* Use this field when allocating the TX descriptors
* Pre-AR93xx TX/RX descriptors will use the ath_desc size; newer ones will
query the HAL for these sizes.
* Introduce TX DMA setup/teardown methods, mirroring what's done in
the RX path.
Although the TX DMA descriptor is setup via ath_desc_alloc() /
ath_desc_free(), there TX status descriptor ring will be allocated
in this path.
* Remove some of the TX EDMA capability probing from the RX path and
push it into the new TX EDMA path.
sized TX descriptor.
This is required for the AR93xx EDMA support which requires 128 byte
TX descriptors (which is significantly larger than the earlier
hardware.)
For now, the only module implement is 'sample', and that's only partially
implemented. The main issue here with reusing this structure in userland
is that it uses 'rix' everywhere, which requires the userland code to
have access to the current HAL rate table.
For now, this is a very large work in progress.
Specific details:
* The rate control information is per-node at the moment and wrapped
in a TLV, to ease parsing and backwards compatibility.
* .. but so I can be slack for now, the userland statistics are just
a copy of the kernel-land sample node state.
* However, for now use a temporary copy and change the rix entries
to dot11rate entries to make it slightly easier to eyeball.
Problems:
* The actual rate information table is unfortunately indexed by rix
and it doesn't contain a rate code. So the userland side of this
currently has no way to extract out a mapping.
TODO:
* Add a TLV payload to dump out the rate control table mapping so
'rix' can be turned into a dot11 / MCS rate.
* .. then remove the temporary copy.
TX descriptor link pointers.
This is required for the AR93xx and later chipsets.
The RX path is slightly different - the legacy RX path directly
accesses ath_desc->ds_link for now, however this isn't at all done
for EDMA (FIFO) RX.
Now, for those performing a little software archeology here:
This is all a bit sub-optimal. "struct ath_desc" is only really relevant
for the pre-AR93xx NICs - where ds_link and ds_data is always in the
same location.
The AR93xx and later NICs have different descriptor layouts altogether.
Now, for AR93xx and later NICs, you should never directly reference
ds_link and ds_data, as:
* the RX descriptors don't have either - the data is _after_ the RX
descriptor. They're just one large buffer. There's also no need for
a per-descriptor RX buffer size as they're all fixed sizes.
* the TX descriptors have 4 buffer and 4 length fields _and_ a link
pointer. Each frame takes up one TX FIFO pointer, but it can contain
multiple subframes (either multiple frames in a buffer, and/or
multiple frames in an aggregate/RIFS burst.)
* .. so, when TX frames are queued to a hardware queue, the link
pointer is ONLY for buffers in that frame/aggregate. The next frame
starts in a new FIFO pointer.
* Finally, descriptor completion status is in a different ring.
I'll write something up about that when its time to do so.
This was inspired by Linux ath9k and the reference driver but is a
reimplementation.
Obtained from: Linux ath9k, Qualcomm Atheros
The DMA FIFO chips (AR93xx and later) differ slightly to th elegacy
chips:
* The RX DMA descriptors don't have a ds_link field;
* The TX DMA descriptors have a ds_link field however at a different
offset.
This is a reimplementation based on what the reference driver and ath9k
does.
A subsequent commit will enable it in the TX and beacon paths.
Obtained from: Linux ath9k, Qualcomm Atheros
The AR9003 series NICs implement a separate RX error to signal that a
Keycache miss occured. The earlier NICs would not set the key index
valid bit.
I'll dig into the difference between "no key index bit set" and "keycache
miss".
* wrap the RX proc calls in the RX refcount;
* call the DFS checking, fast frames staging and TX rescheduling if
required.
TODO:
* figure out if I can just make "do TX rescheduling" mean "schedule
TX taskqueue" ?
with fresh descriptors, before handling the frames.
Wrap it all in the RX locks.
Since the FIFO is very shallow (16 for HP, 128 for LP) it needs to be
drained and replenished very quickly. Ideally, I'll eventually move this
RX FIFO drain/fill into the interrupt handler, only deferring the actual
frame completion.
I was setting up the RX EDMA buffer to be 4096 bytes rather than the
RX data buffer portion. The hardware was likely getting very confused
and DMAing descriptor portions into places it shouldn't, leading to
memory corruption and occasional panics.
Whilst here, don't bother allocating descriptors for the RX EDMA case.
We don't use those descriptors. Instead, just allocate ath_buf entries.
the FIFO.
I still see some corner cases where no RX occurs when it should be
occuring. It's quite possible that there's a subtle race condition
somewhere; or maybe I'm not programming the RX queues right.
There's also no locking here yet, so any reset/configuration path
state change (ie, enabling/disabling receive from the ioctl, net80211
taskqueue, etc) could quite possibly confuse things.
* For now, kickpcu should hopefully just do nothing - the PCU doesn't need
'kicking' for Osprey and later NICs. The PCU will just restart once
the next FIFO entry is pushed in.
* Teach "proc" about "dosched", so it can be used to just flush the
FIFO contents without adding new FIFO entries.
* .. and now, implement the RX "flush" routine.
* Re-initialise the FIFO contents if the FIFO is empty (the DP is NULL.)
When PCU RX is disabled (ie, writing RX_D to the RX configuration
register) then the FIFO will be completely emptied. If the software FIFO
is full, then no further descriptors are pushed into the FIFO and
things stall.
This all requires much, much more thorough stress testing.
This is inspired by ath9k and the reference driver, but it's a new
implementation of the RX FIFO handling.
This has some issues - notably the FIFO needs to be reprogrammed when
the chip is reset.
* Add a couple of RX errors;
* Add the spectral scan PHY error code;
* extend the RX flags to be a 16 bit field, rather than an 8 bit field;
* Add a new RX flag.
Obtained from: Qualcomm Atheros
The AR93xx and later chips support two RX FIFO queues - a high and low
priority queue.
For legacy chips, just assume the queues are high priority.
This is inspired by the reference driver but is a reimplementation of
the API and code.
AR93xx receive descriptors.
This isn't entirely complete - the AR93xx and later descriptors
don't have a link/buffer pointer; the descriptor contents just
start.
The RX EDMA support requires a modified approach to the RX descriptor
handling.
Specifically:
* There's now two RX queues - high and low priority;
* The RX queues are implemented as FIFOs; they're now an array of pointers
to buffers;
* .. and the RX buffer and descriptor are in the same "buffer", rather than
being separate.
So to that end, this commit abstracts out most of the RX related functions
from the bulk of the driver. Notably, the RX DMA/buffer allocation isn't
updated, primarily because I haven't yet fleshed out what it should look
like.
Whilst I'm here, create a set of matching but mostly unimplemented EDMA
stubs.
Tested:
* AR9280, station mode
TODO:
* Thorough AP and other mode testing for non-EDMA chips;
* Figure out how to allocate RX buffers suitable for RX EDMA, including
correctly setting the mbuf length to compensate for the RX descriptor
and completion status area.
as an EDMA check function.
For the AR9003 and later NICs, different TX/RX DMA and descriptor handling
code will be conditional on the EDMA check.
Obtained from: Qualcomm Atheros
* Add a new ANI variable, for AR9003 and later chips;
* The AR9003 and later series chips support two RX queues now, so start
down the road of supporting that;
* Add some new TX queue types - uAPSD is possible on earlier chips,
but PAPRD is relevant to AR9003 and later.
Obtained from: Qualcomm Atheros, Linux ath9k
with AMPDU aggregate delimiters.
If there's an OFDM restart during an aggregate, the hardware ACKs
the previous frame, but communicates the RXed frame to the hardware
as having had CRC delimiter error + OFDM_RESTART phy error.
The frame however didn't have a CRC error and since the hardware ACKed
the aggregate to the sender, it thinks the frame was received.
Since I have no idea how often this occurs in the real world, add a
debug statement so trigger whenever this occurs. I'd appreciate an
email if someone finds this particular situation is triggered.
The Linux ath9k btcoex code is based off of this code.
Note this doesn't actually implement functional btcoex; there's some
driver glue and a whole lot of verification that is required.
On the other hand, I do have the AR9285+BT and AR9287+BT NICs which
this code supports..
Obtained from: Qualcomm Atheros, Linux ath9k
the assumption that ath_softc doesn't change size based on build time
configuration.
I picked up on this because suddenly radar stuff didn't work; and
although the ath_dfs code was setting sc_dodfs=1, the main ath driver
saw sc_dodfs=0.
So for now, include opt_ath.h in driver source files. This seems like
the sane thing to do anyway.
I'll have to do a pass over the code at some later stage and turn
the radiotap TX/RX structs into malloc'ed memory, rather than in-line
inside of ath_softc. I'd rather like to keep ath_softc the same
layout regardless of configuration parameters.
Pointy hat to: adrian
a buffer pointer.
For large radar pulses, the AR9130 and later will return a series of
FFT results for software processing. These can overflow a single 2KB
buffer on longer pulses. This would result in undefined buffer behaviour.
This includes a few new fields in each RXed frame:
* per chain RX RSSI (ctl and ext);
* current RX chainmask;
* EVM information;
* PHY error code;
* basic RX status bits (CRC error, PHY error, etc).
This is primarily to allow me to do some userland PHY error processing
for radar and spectral scan data. However since EVM and per-chain RSSI
is provided, others may find it useful for a variety of tasks.
The default is to not compile in the radiotap vendor extensions, primarily
because tcpdump doesn't seem to handle the particular vendor extension
layout I'm using, and I'd rather not break existing code out there that
may be (badly) parsing the radiotap data.
Instead, add the option 'ATH_ENABLE_RADIOTAP_VENDOR_EXT' to your kernel
configuration file to enable these options.
and the CRC error bits set. The radar payload is correct.
When this happens, the stack doesn't see them PHY error frames and
isn't interpreted as a PHY error. So, no radar detection and no radiotap
PHY error handling.
Now, this may introduce some weird issues if the MAC sends up some other
combination of CRC error + PHY error frames; this commit would break that
and mark them as PHY errors instead of CRC errors.
I may tinker with this a little more to pass radar/early radar/spectral
frames up as PHY errors if the CRC bit is set, to restore the previous
behaviour (where if CRC is set on a PHY error frame, it's marked as a CRC
error rather than PHY error.)
Tested on: AR5416, over the air, to a USRP N200 which is generating a
large number of a variety of radar pulses.
TODO: Test on AR9130, AR9160, AR9280 (and maybe radar pulses on
2GHz on AR9285/AR9287.)
PR: kern/169362
* Add an OS_A_REG_WRITE() routine - analog writes require a 100usec delay
on AR9280 and later, so create a method to do it.
* Use it for the AR9287 analog writes.
* Re-indent and style(9) the code.
This just requires a little HAL change (add a new config parameter) and
some glue in if_ath_pci.c, however I'm leaving this up for someone else
to do.
Obtained from: Qualcomm Atheros
* Use ATH_RC_NUM instead of '4' when iterating over the ratecontrol series
array.
* A few style(9) fixes, hopefully no regressions here.
* Add some comments that better describe what's going on.
The existing code tries to use the beacon miss timer to signal that the AP
has gone away. Unfortunately this doesn't seem to be behaving itself.
I'll try to investigate why this is for the sake of completeness.
The result is the STA will stay "associated" to the AP it was associated
with when it suspended. It never receives a bmiss notification so it
never tries reassociating.
PR: kern/169084
* Resize some types. In particular, bfs_seqno can be uint16_t for now.
Previous work would assign the unassigned seqno a value of -1, which
I obviously can't do here.
* Remove bfs_pktdur. It was in the original code but nothing so far uses
it.
This gets ath_buf down (on my i386 system) to 292 bytes from 300 bytes.
I'd rather it be much, much smaller.
fixed for 802.11n TX, this needs to be disabled or users wlil see randomly
hanging aggregation sessions.
Whilst I'm here, remove the warning about 802.11n being full of dragons.
It's nowhere near that scary now.
ath_start() is called.
This (defaults to 10 frames) gives for a little headway in the TX ath_buf
allocation, so buffer cloning is still possible.
This requires a lot omre experimenting and tuning.
It also doesn't stop a node/TID from consuming all of the available
ath_buf's, especially when the node is going through high packet loss
or only talking at a low TX rate. It also doesn't stop a paused TID
from taking all of the ath_bufs. I'll look at fixing that up in subsequent
commits.
PR: kern/168170
traffic.
* Create sc_mgmt_txbuf and sc_mgmt_txdesc, initialise/free them appropriately.
* Create an enum to represent buffer types in the API.
* Extend ath_getbuf() and _ath_getbuf_locked() to take the above enum.
* Right now anything sent via ic_raw_xmit() allocates via ATH_BUFTYPE_MGMT.
This may not be very useful.
* Add ATH_BUF_MGMT flag (ath_buf.bf_flags) which indicates the current buffer
is a mgmt buffer and should go back onto the mgmt free list.
* Extend 'txagg' to include debugging output for both normal and mgmt txbufs.
* When checking/clearing ATH_BUF_BUSY, do it on both TX pools.
Tested:
* STA mode, with heavy UDP injection via iperf. This filled the TX queue
however BARs were still going out successfully.
TODO:
* Initialise the mgmt buffers with ATH_BUF_MGMT and then ensure the right
type is being allocated and freed on the appropriate list. That'd save
a write operation (to bf->bf_flags) on each buffer alloc/free.
* Test on AP mode, ensure that BAR TX and probe responses go out nicely
when the main TX queue is filled (eg with paused traffic to a TID,
awaiting a BAR to complete.)
PR: kern/168170
(or direct dispatch) behind the TXQ lock (which, remember, is doubling
as the TID lock too for now.)
This ensures that:
(a) the sequence number and the CCMP PN allocation is done together;
(b) overlapping transmit paths don't interleave frames, so we don't
end up with the original issue that triggered kern/166190.
Ie, that we don't end up with seqno A, B in thread 1, C, D in
thread 2, and they being queued to the software queue as "A C D B"
or similar, leading to the BAW stalls.
This has been tested:
* both STA and AP modes with INVARIANTS and WITNESS;
* TCP and UDP TX;
* both STA->AP and AP->STA.
STA is a Routerstation Pro (single CPU MIPS) and the AP is a dual-core
Centrino.
PR: kern/166190
scheduled from the head of the software queue rather than trying to
queue the newly given frame.
This leads to some rather unfortunate out of order (but still valid
as it's inside the BAW) frame TX.
This now:
* Always queues the frame at the end of the software queue;
* Tries to direct dispatch the frame at the head of the software queue,
to try and fill up the hardware queue.
TODO:
* I should likely try to queue as many frames to the hardware as I can
at this point, rather than doing one at a time;
* ath_tx_xmit_aggr() may fail and this code assumes that it'll schedule
the TID. Otherwise TX may stall.
PR: kern/166190
This is an unfortunate byproduct of how the routine is used - it's called
with the head frame on the queue, but if the frame is failed, it's inserted
into the tail of the queue.
Because of this, the sequence numbers would get all shuffled around and
the BAW would be bumped past this sequence number, that's now at the
end of the software queue. Then, whenever it's time for that frame
to be transmitted, it'll be immediately outside of the BAW and TX will
stall until the BAW catches up.
It can also result in all kinds of weird duplicate BAW frames, leading
to hilarious panics.
PR: kern/166190
This showed up when doing heavy UDP throughput on SMP machines.
The problem with this is because the 802.11 sequence number is being
allocated separately to the CCMP PN replay number (which is assigned
during ieee80211_crypto_encap()).
Under significant throughput (200+ MBps) the TX path would be stressed
enough that frame TX/retry would force sequence number and PN allocation
to be out of order. So once the frames were reordered via 802.11 seqnos,
the CCMP PN would be far out of order, causing most frames to be discarded
by the receiver.
I've fixed this in some local work by being forced to:
(a) deal with the issues that lead to the parallel TX causing out of
order sequence numbers in the first place;
(b) fix all the packet queuing issues which lead to strange (but mostly
valid) TX.
I'll begin fixing these in a subsequent commit or five.
PR: kern/166190
it turns out that it negatively affects performance. I'm stil investigating
exactly why deferring the IO causes such negative TCP performance but
doesn't affect UDP preformance.
Leave the ath_tx_kick() change in there however; it's going to be useful
to have that there for if_transmit() work.
PR: kern/168649
called to "kick" along TX.
For now, schedule a taskqueue call.
Later on I may go back to the direct call of ath_rx_tasklet() - but for
now, this will do.
I've tested UDP and TCP TX. UDP TX still achieves 240MBit, but TCP
TX gets stuck at around 100MBit or so, instead of the 150MBit it should
be at. I'll re-test with no ACPI/power/sleep states enabled at startup
and see what effect it has.
This is in preparation for supporting an if_transmit() path, which will
turn ath_tx_kick() into a NUL operation (as there won't be an ifnet
queue to service.)
Tested:
* AR9280 STA
TODO:
* test on AR5416, AR9160, AR928x STA/AP modes
PR: kern/168649
implementing parallel TX and TX/RX completion can be done without
simply abusing long-held locks.
Right now, multiple concurrent ath_start() entries can result in
frames being dequeued out of order. Well, they're dequeued in order
fine, but if there's any preemption or race between CPUs between:
* removing the frame from the ifnet, and
* calling and runningath_tx_start(), until the frame is placed on a
software or hardware TXQ
Then although dequeueing the frame is in-order, queueing it to the hardware
may be out of order.
This is solved in a lot of other drivers by just holding a TX lock over
a rather long period of time. This lets them continue to direct dispatch
without races between dequeue and hardware queue.
Note to observers: if_transmit() doesn't necessarily solve this.
It removes the ifnet from the main path, but the same issue exists if
there's some intermediary queue (eg a bufring, which as an aside also
may pull in ifnet when you're using ALTQ.)
So, until I can sit down and code up a much better way of doing parallel
TX, I'm going to leave the TX path using a deferred taskqueue task.
What I will likely head towards is doing a direct dispatch to hardware
or software via if_transmit(), but it'll require some driver changes to
allow queues to be made without using the really large ath_buf / ath_desc
entries.
TODO:
* Look at how feasible it'll be to just do direct dispatch to
ath_tx_start() from if_transmit(), avoiding doing _any_ intermediary
serialisation into a global queue. This may break ALTQ for example,
so I have to be delicate.
* It's quite likely that I should break up ath_tx_start() so it
deposits frames onto the software queues first, and then only fill
in the 802.11 fields when it's being queued to the hardware.
That will make the if_transmit() -> software queue path very
quick and lightweight.
* This has some very bad behaviour when using ACPI and Cx states.
I'll do some subsequent analysis using KTR and schedgraph and file
a follow-up PR or two.
PR: kern/168649
These aren't strictly needed at the moment as we're not doing APSM
and forcing the NIC in and out of network sleep. But, they don't hurt.
Tested:
* AR9280 (mini-PCIe)
Obtained from: Qualcomm Atheros, Linux ath9k
* Now that ah_configPCIE is called for both power on and suspend/resume,
make sure the right bit(s) are cleared and set when suspending and
resuming. Specifically:
+ force disable/enable the PCIe PHY upon suspend/resume;
+ reprogram the PCIe WAR register when resuming and upon power-on.
* Add a recipe which powers down any PCIe PHY hardware inside the AR5416
(which is the PCI variant) to save on power. I have (currently) no way
to test exactly how much power is saved, if any.
Tested on:
* AR5416 cardbus - although unfortunately pccard/cbb/cardbus currently
detaches the NIC upon suspend, I don't think it's a proper test case.
* AR5418 PCIe attached to expresscard - since we're not doing PCIe APSM,
it's also not likely a full/good test case.
In both instances I went through a handful of suspend/resume cycles and
ensured that the STA vap reassociated correctly.
TODO:
* Setup a laptop to simply sit in a suspend/resume loop, making sure that
the NIC always correctly comes back;
* Start doing suspend/resume tests with actual traffic going on in the
background, as I bet this process is all quite racy at the present;
* Test adhoc/hostap mode, just to be completely sure it's working correctly;
* See if I can jury rig an external power source to an AR5416 to test out
whether ah_disablePCIE() works.
Obtained from: Qualcomm Atheros
* Add some other WAR bits (very usefully described too) in preparation for
porting over some suspend/resume fixes from ath9k/Atheros.
Obtained from: Qualcomm Atheros
not to disable the PCIe PHY in prepration for reset.
Extend the enablepci method to have a "poweroff" flag, which if equal
to true means the hardware is about to go to sleep.
* Flesh out the pcie disable method for 11n chips, as they were defaulting
to the AR5212 (empty) PCIe disable method.
* Add accessor macros for the HAL PCIe enable/disable calls.
* Call disable on ath_suspend()
* Call enable on ath_resume()
NOTE:
* This has nothing to do with the NIC sleep/run state - the NIC still
will stay in network-run state rather than supporting network-sleep
state. This is preparation work for supporting correct suspend/resume
WARs for the 11n PCIe NICs.
TODO:
* It may be feasible at this point to keep the chip powered down during
initial probe/attach and only power it up upon the first configure/reset
pass. This however would require correct (for values of "correct")
tracking of the NIC power configuration state from the driver and that
just isn't attempted at the moment.
Tested:
* AR9280 on my Lenovo T60, but with no suspend/resume pass (yet).
I'll have to leave this high for now, until I've done some significant
surgery with how ath_bufs (and descriptors) are handled.
This should significantly cut down on the opportunities for a full TX
queue hanging traffic. I'll continue making things work though; I'm
mostly doing this for users. :)
I've come across a weird scenario in net80211 where two TX streams will
happily attempt to setup an aggregation session together.
If we're very lucky, it happens concurrently on separate CPUs and the
total lack of locking in the net80211 aggregation code causes this stuff
to race. Badly.
So >1 call would occur to the ath(4) addba start, but only one call would
complete to addba complete or timeout. The TID would thus stay paused.
The real fix is to implement some proper per-node (or maybe per-TID)
locking in net80211, which then could be leveraged by the ath(4) TX
aggregation code.
Whilst I'm at it, shuffle around the debugging messages a bit.
I like to keep people on their toes.
There's some TX path TDMA code in if_ath_tx.c which should be migrated
out, but first I should likely try and verify/fix/repair the TDMA support
in 9.x and -HEAD.
* migrate the rx processing out into if_ath_rx.c
* migrate the TSF functions into if_ath_tsf.h, as inlines
This is in prepration for supporting the EDMA RX routines, required to
support the AR93xx series NICs.
TODO:
* ath_start() shouldn't be private, but it's called as part of
the RX path. I should likely migrate ath_rx_tasklet() back into
if_ath.c and then return this to be 'static'. The RX code really
shouldn't need to see TX routines (and vice versa.)
* ath_beacon_* should be in if_ath_beacon.[ch].
* ath_tdma_* should be in if_ath_tdma.[ch] ...
add some more BAR debugging logic.
* Change the definition of ath_debug and ath_softc.sc_debug from
int to uint64_t;
* Change the relevant sysctls;
* Add a new BAR TX debugging field;
* Use this in if_ath_tx.
This has been tested by using the sysctl program, which happily allows
for fields > 32 bits to be configured.
Although I _should_ handle the other errors in various ways (specifically
errors like FILT), treating them as having transmitted successfully
is completely wrong. Here, they'd be counted as successful and the BAW
would be advanced.. but the RX side wouldn't have received them.
The specific errors I've been seeing here are HAL_TXERR_FILT.
This patch does fix the issue - I've tested it using -i 0.001 pings
(enough to start aggregation) and now the behaviour is correct:
* The RX side never sees a "moved window" error, and
* The TX side sends BARs as needed, with the RX side correctly handling
them.
PR: kern/167902
TX and RX PCU stop/drain routines have been thoroughly debugged.
It's also very likely that I should add hooks back up to the
interface glue (if_ath_pci / if_ath_ahb) to do any relevant
bus flushes that are required. A WMAC DDR flush may be required
for the AR9130 SoC.
in the HAL. That's very memory hungry (32k just for channel statistics)
which would be better served by keeping a summary in the ANI state.
Or, later, keep a survey history in net80211.
So:
* Migrate the ah_chansurvey array to be a single entry, for the current
channel.
* Change the ioctl interface and ANI code to just reference that.
* Clear the ah_chansurvey array during channel reset, both in the AR5212
and AR5416 reset path.
* Always call ar5416GetListenTime()
* Modify ar5416GetListenTime() to:
+ don't update the ANI state if there isn't any ANI state;
+ don't update the channel survey state if there's no active
channel - just to be paranoid
+ copy the channel survey results into the current sample slot
based on the current channel; then increment the sample counter
and sample history counter.
* Modify ar5416GetMIBCyclesPct() to simply return a HAL_SURVEY_SAMPLE,
rather than a set of percentages. The ANI code wasn't using the
percentages anyway.
TODO:
* Create a new function which fetches the survey results periodically
* .. then modify the ANI code to use the pre-fetched values rather than
fetching them again
* Roll the 11n ext busy function from ar5416_misc.c to update all the
counters, then do the result calculation
* .. then, modify the MIB counter routine to correctly fetch a snapshot -
freeze the counters, fetch the values, then reset the counters.
The reference driver has a 3ms delay for the AR9130 but I'm not as yet
sure why. From what I can gather, it's likely waiting for some FIFO
flush to occur.
At some point in the future it may be worthwhile adding a WMAC
FIFO flush here, but that'd require some side-call through to the SoC
DDR flush routines.
Obtained from: Atheros
