syscall return values should be cleared. The system calls
getcontext() and swapcontext() want to return 0 on success
but these contexts can be switched to at a later time so
the return values need to be cleared in the saved register
sets. Other callers of get_mcontext() would normally want
the context without clearing the return values.
Remove the i386-specific context saving from the KSE code.
get_mcontext() is not i386-specific any more.
Fix a bad pointer in the alpha get_mcontext() code. The
context was being bcopy()'d from &td->tf_frame, but tf_frame
is itself a pointer, so the thread was being copied instead.
Spotted by jake.
Glanced at by: jake
Reviewed by: bde (months ago)
to get actual constant values. This is in preparation for machine/limits.h
retirement.
Discussed on: standards@
Submitted by: Craig Rodrigues <rodrigc@attbi.com> (*)
Modified by: kan
ethernet controller. The driver has been tested with the LinkSys
USB200M adapter. I know for a fact that there are other devices out
there with this chip but don't have all the USB vendor/device IDs.
Note: I'm not sure if this will force the driver to end up in the
install kernel image or not. Special magic needs to be done to exclude
it to keep the boot floppies from bloating again, someone please
advise.
the cpu dependent files. It will need to be done differently for USIII.
- Simplify the logic for detecting context rollovers. Instead of dealing
with it when the next context switch would cause the context numbers to
rollover, deal with it when they actually do rollover.
- Move some things around in cpu_switch so that we only do 1 membar #Sync
when switching address space, instead of 2.
- Detect kernel threads by comparing the new vm space to vmspace0, instead
if checking if the tlb context is 0.
- Removed some debug code.
enum to an int and redefine the BUS_DMASYNC_* constants as
flags. This allows us to specify several operations in one
call to bus_dmamap_sync() as in NetBSD.
of asserting that an mbuf has a packet header. Use it instead of hand-
rolled versions wherever applicable.
Submitted by: Hiten Pandya <hiten@unixdaemons.com>
These are called through function pointers so that different implementations
can be provided for cheetah, where the block load instructions may or may
not be a win, and so they can be disabled with the machdep.use_vis tunable.
In terms of raw bandwidth the integer versions are faster, but not allocating
lines in the L2 cache for useless data gives a measurable improvement in user
time for the benchmarks I tested (mostly buildworld with -j8).
As far as I can tell the instructions used are implemented on everything
back to UltraSPARC I, so there should not be a problem with different cpu
types.
to take care of the KAME IPv6 code which needs ovbcopy() because NetBSD's
bcopy() doesn't handle overlap like ours.
Remove all implementations of ovbcopy().
Previously, bzero was a function pointer on i386, to save a jmp to
bzero_vector. Get rid of this microoptimization as it only confuses
things, adds machine-dependent code to an MD header, and doesn't really
save all that much.
This commit does not add my pagezero() / pagecopy() code.
can do 64 bytes at a time and don't allocate lines in the L2 cache. These
assume that everything is 64 byte aligned, and that there's more than 128
bytes of data (best for whole pages). The block load and store instructions
don't follow normal memory ordering rules and require either a memory barrier
or move between registers before the data can actually be used. This
implementation correctly shuffles around 3 out of the 4 sets of registers
in order to avoid memory barriers expect for the last 2 blocks.
will be saved if we context switch as a result of an interrupt which occured
while using the floating point registers in the kernel (which actually can't
happen right now). This allows fp disabled traps in the kernel, which
normally shouldn't happen, so make sure the trapping code is what we expect
it is.
used to support block copy and zero operations in the kernel which use the
floating point registers.
- While I'm changing the size, improve the layout of struct pcb, sort by size,
then alphabetical etc.
- Add some assertions to validate assumptions made about how the pcb is
allocated.
for temporaries relating to the state of the new process instead of the
outs, so that functions can be called without fear of clobbering them.
- Use savefpctx instead of rolling our own.
as it could be and can do with some more cleanup. Currently its under
options LAZY_SWITCH. What this does is avoid %cr3 reloads for short
context switches that do not involve another user process. ie: we can
take an interrupt, switch to a kthread and return to the user without
explicitly flushing the tlb. However, this isn't as exciting as it could
be, the interrupt overhead is still high and too much blocks on Giant
still. There are some debug sysctls, for stats and for an on/off switch.
The main problem with doing this has been "what if the process that you're
running on exits while we're borrowing its address space?" - in this case
we use an IPI to give it a kick when we're about to reclaim the pmap.
Its not compiled in unless you add the LAZY_SWITCH option. I want to fix a
few more things and get some more feedback before turning it on by default.
This is NOT a replacement for Bosko's lazy interrupt stuff. This was more
meant for the kthread case, while his was for interrupts. Mine helps a
little for interrupts, but his helps a lot more.
The stats are enabled with options SWTCH_OPTIM_STATS - this has been a
pseudo-option for years, I just added a bunch of stuff to it.
One non-trivial change was to select a new thread before calling
cpu_switch() in the first place. This allows us to catch the silly
case of doing a cpu_switch() to the current process. This happens
uncomfortably often. This simplifies a bit of the asm code in cpu_switch
(no longer have to call choosethread() in the middle). This has been
implemented on i386 and (thanks to jake) sparc64. The others will come
soon. This is actually seperate to the lazy switch stuff.
Glanced at by: jake, jhb
set_mcontext.
- Don't make assumptions about the alignment of the mcontext inside of the
ucontext; we have to save the floating point registers to the pcb and then
copy to the mcontext.
a pointer that is in user space. It will be used as the basic primitive
for a kernel supported user space lock implementation.
- Implement this function in x86's support.s
- Provide stubs that return -1 in all other architectures. Implementations
will follow along shortly.
Reviewed by: jake
a follow on commit to kern_sig.c
- signotify() now operates on a thread since unmasked pending signals are
stored in the thread.
- PS_NEEDSIGCHK moves to TDF_NEEDSIGCHK.
- Change all consumers to pass in a thread.
Right now this does not cause any functional changes but it will be important
later when signals can be delivered to specific threads.
be overridden by setting hw.physmem.
- Fix a vm_map_find arg, we don't want to find space.
- Add tracing and statistics for off colored pages.
- Detect "stupid" pmap_kenters (same virtual and physical as existing
mapping), and do nothing in that case.
pages which represent actual physical memory we must strip off the fake
page in order to allow illegal aliases to be detected. Otherwise we map
uncacheable in the virtual and physical caches and set the side effect bit,
as is required for mapping device memory.
This fixes gstat on sparc64, which wants to mmap kernel memory through a
character device.
where physical addresses larger than virtual addresses, such as i386s
with PAE.
- Use this to represent physical addresses in the MI vm system and in the
i386 pmap code. This also changes the paddr parameter to d_mmap_t.
- Fix printf formats to handle physical addresses >4G in the i386 memory
detection code, and due to kvtop returning vm_paddr_t instead of u_long.
Note that this is a name change only; vm_paddr_t is still the same as
vm_offset_t on all currently supported platforms.
Sponsored by: DARPA, Network Associates Laboratories
Discussed with: re, phk (cdevsw change)
in busdma tags. There are currently no tags shared accross
different drivers so this isn't needed at the moment, but it
will be required when we'll have a proper newbus method to get
the parent busdma tag.
on future UltraSPARC cpus for which the data cache is not direct mapped.
- Move UltraSPARC I and II (spitfire, blackbird, sapphire, sabre) specific
functions to spitfire.c, and add cheetah.c for UltraSPARC III specific
functions. Initially just cache flushing, but there are a few other
functions that will need to move here.
- Add an ipi handler for data cache flushing on UltraSPARC III.
- Use function pointers to select the right cache flushing functions based
on cpu_impl.
With this it is possible to boot single user from an mfs root on UltraSPARC
III systems, including spinning up secondary processors. There is currently
no support for the host to pci bridge, and no documentation for it is
publically available.
Thanks to Oleg Derevenetz for providing access to a system with UltraSPARC
III+ cpus.
UltraSPARC III and higher cpus and do needed setup.
- Disable the "system tick" interrupt for UltraSPARC III. This avoids
an interrupt storm on startup since we're not prepared for these at
all. This feature has questionable use anyway.
- Clear tick on startup and then leave it alone.
