- The feature is dangerous because the kernel code didn't check
validity of the memory address provided from user space.
- It seems that mdconfig(8) never really supported attaching preloaded
memory disks.
- Preloaded memory disks are automatically attached during md(4)
initialization. Thus there shouldn't be much use for the feature.
PR: kern/169683
Discussed on: freebsd-hackers
encryption types.
The AR5210 only has four WEP key slots, in contrast to what the
later MACs have (ie, the keycache.) So there's no way to store a "clear"
key.
Even if the driver is taught to not allocate CLR key entries for
the AR5210, the hardware will actually attempt to decode the encrypted
frames with the (likely all 0!) WEP keys.
So for now, disable the hardware encryption entirely and just so it
all in software. That allows both WEP -and- WPA to actually work.
If someone wishes to try and make hardware WEP _but_ software WPA work,
they'll have to create a HAL capability to enable/disable hardware
encryption based on the current STA/Hostap mode. However, making
multi-vap work with one WEP and one WPA VAP will require hardware
encryption to be disabled anyway.
from HDMI/DisplayPort devices in form of general connection status and
sound(4)-style channel matrix. Now that information is only reported in
readable form to verbose logs, but potentially could be used by sound(4)
to correctly choose default devices and configure vchans.
Fix rear and side channels swap on analog 7.1 outputs. As soon as there is
a huge mess in industry about naming and using of these channels, duplicate
rear channels of 4 and 5.1 streams to both read and side speakers.
* For CABQ traffic, I -can- chain them together using the next pointer
and just push that particular chain head to the CABQ. However, this
doesn't magically make EDMA TX CABQ work - I have to do some further
hoop jumping.
* upon setup, tell the alq code what the chip information is.
* add TX/RX path logging for legacy chips.
* populate the tx/rx descriptor length fields with a best-estimate.
It's overly big (96 bytes when AH_SUPPORT_AR5416 is enabled)
but it'll do for now.
Whilst I'm here, add CURVNET_RESTORE() here during probe/attach as a
partial solution to fixing crashes during attach when the attach fails.
There are other attach failures that I have to deal with; those'll come
later.
* Add a new method which allows the driver to push the MAC/phy/hal info
into the logging stream.
* Add a new ALQ logging entry which logs the mac/phy/hal information.
* Modify the ALQ startup path to log the MAC/phy/hal information
so the decoder knows which HAL/chip is generating this information.
* Convert the header and mac/phy/hal information to use be32, rather than
host order. I'd like to make this stuff endian-agnostic so I can
decode MIPS generated logs on a PC.
This requires some further driver modifications to correctly log the
right initial chip information.
Also - although noone bar me is currently using this, I've shifted the
debug bitmask around a bit. Consider yourself warned!
This was broken by me when merging the 802.11n aggregate descriptor chain
setup with the default descriptor chain setup, in preparation for supporting
AR9380 NICs.
The corner case here is quite specific - if you queue an aggregate frame
with >1 frames in it, and the last subframe has only one descriptor making
it up, then that descriptor won't have the rate control information
copied into it. Look at what happens inside ar5416FillTxDesc() if
both firstSeg and lastSeg are set to 1.
Then when ar5416ProcTxDesc() goes to fill out ts_rate based on the
transmit index, it looks at the rate control fields in that descriptor
and dutifully sets it to be 0.
It doesn't happen for non-aggregate frames - if they have one descriptor,
the first descriptor already has rate control info.
I removed the call to ath_hal_setuplasttxdesc() when I migrated the
code to use the "new" style aggregate chain routines from the HAL.
But I missed this particular corner case.
This is a bit inefficient with MIPS boards as it involves a few redundant
writes into non-cachable memory. I'll chase that up when it matters.
Tested:
* AR9280 STA mode, TCP iperf traffic
* Rui Paulo <rpaulo@> first reported this and has verified it on
his AR9160 based AP.
PR: kern/173636
This alleviates issues on newer Sandy/Ivy Bridge gear that seems to require
boatloads more ACPI resources than before.
Reviewed by: avg@
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
This happens during a scan in STA mode; any queued data frames will
be power save queued but as there's no TIM in STA mode, it panics.
This was introduced by me when I disabled my driver-aware power save
handling support.
actual traffic with an AR9380/AR9382/AR9485.
The sample rate control stats would show impossibly large numbers for
"successful packets transmitted." The number was a tad under 2^^64-1.
So after a bit of digging, I found that the sample rate control code
was making 'tries' turn into a negative number.. and this was because
ts_longretry was too small.
The hardware returns "ts_longretry" at the current rate selection,
not overall for that TX descriptor. So if you setup four TX rate
scenarios and the second one works, ts_longretry is only set for
the number of attempts at that second rate scenario. The FreeBSD HAL
code does the correction in ath_hal_proctxdesc() - however, this isn't
possible with EDMA.
EDMA TX completion is done separate from the original TX descriptor.
So the real solution is to split out "find ts_rate and ts_longretry"
from "complete TX descriptor". Until that's done, put a hack in
the EDMA TX path that uses the rate scenario information in the ath_buf.
Tested: AR9380, AR9382, AR9485 STA mode
in nve(4). The OS_API structure defined in os.h expects NV_API_CALL
attributes, effectively regparm(0), on its function pointers, but all
the functions were declared and defined without this attribute.
MFC after: 1 week
DWC OTG driver. Fix a hang issue when using LOW and FULL speed
BULK traffic. Make sure we don't ask for data in the last
microframe. This allows using devices like USB mice and USB
keyboards connected to the RPI-B.
Suggested by: gonzo @
