spending, which was unused now that all software interrupts have
their own thread. Make the legacy schednetisr use an atomic op
for setting bits in the netisr mask.
Reviewed by: jhb
Also, while here, run up to 32 interrupt sources on APIC systems.
Normalize INTREN/INTRDIS so they are the same on both UP and SMP systems
rather than sometimes a macro, and sometimes a function.
Reviewed by: jhb, jakeb
MPLOCKED macro
(2) Use decimal 12 rather than hex 0xc in an addl
(3) Implement MTX_ENTER for the I386_CPU case
(4) Use semi-colons between instructions to allow MTX_ENTER
and MTX_ENTER_WITH_RECURSION to be assembled
(5) Use incl instead of incw to increment the recusion count
(6) 10 is not a valid label, use 7, 8 and 9 rather than 8, 9 and 10
(7) Sort numeric labels
Submitted by: bde (2, 4, and 5)
process is on the alternate stack or not. For compatibility
with sigstack(2) state is being updated if such is needed.
We now determine whether the process is on the alternate
stack by looking at its stack pointer. This allows a process
to siglongjmp from a signal handler on the alternate stack
to the place of the sigsetjmp on the normal stack. When
maintaining state, this would have invalidated the state
information and causing a subsequent signal to be delivered
on the normal stack instead of the alternate stack.
PR: 22286
-current and RELENG_4 with GENERIC.
NKPT is the number of initial bootstrap page table pages we create for
the kernel during startup. Once VM is up, we resize it as needed, but
with 4G ram, the size of the vm_page_t structures was pushing it over
the limit. The fact that trimmed down kernels boot on 4G ram machines
suggests that we were pretty close to the edge.
The "30" is arbitary, but smaller than the 'nkpt' variable on all
machines that I checked.
timeout. If DIAGNOSTIC is turned on, then display a message to the console
with a map of which CPUs failed to stop or restart. This gives an SMP box
at least a fighting chance of getting into DDB if one of the other CPUs has
interrupts disabled.
counter register in-CPU.
This is to be used as a fast "timer", where linearity is more important
than time, and multiple lines in the linearity caused by multiple CPUs
in an SMP machine is not a problem.
This adds no code whatsoever to the FreeBSD kernel until it is actually
used, and then as a single-instruction inline routine (except for the
80386 and 80486 where it is some more inline code around nanotime(9).
Reviewed by: bde, kris, jhb
syscall compare against a variable sv_minsigstksz in struct
sysentvec as to properly take the size of the machine- and
ABI dependent struct sigframe into account.
The SVR4 and iBCS2 modules continue to have a minsigstksz of
8192 to preserve behavior. The real values (if different) are
not known at this time. Other ABI modules use the real
values.
The native MINSIGSTKSZ is now defined as follows:
Arch MINSIGSTKSZ
---- -----------
alpha 4096
i386 2048
ia64 12288
Reviewed by: mjacob
Suggested by: bde
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
reducues the maintenance load for the mutex code. The only MD portions
of the mutex code are in machine/mutex.h now, which include the assembly
macros for handling mutexes as well as optionally overriding the mutex
micro-operations. For example, we use optimized micro-ops on the x86
platform #ifndef I386_CPU.
- Change the behavior of the SMP_DEBUG kernel option. In the new code,
mtx_assert() only depends on INVARIANTS, allowing other kernel developers
to have working mutex assertiions without having to include all of the
mutex debugging code. The SMP_DEBUG kernel option has been renamed to
MUTEX_DEBUG and now just controls extra mutex debugging code.
- Abolish the ugly mtx_f hack. Instead, we dynamically allocate
seperate mtx_debug structures on the fly in mtx_init, except for mutexes
that are initiated very early in the boot process. These mutexes
are declared using a special MUTEX_DECLARE() macro, and use a new
flag MTX_COLD when calling mtx_init. This is still somewhat hackish,
but it is less evil than the mtx_f filler struct, and the mtx struct is
now the same size with and without mutex debugging code.
- Add some micro-micro-operation macros for doing the actual atomic
operations on the mutex mtx_lock field to make it easier for other archs
to override/optimize mutex ops if needed. These new tiny ops also clean
up the code in some places by replacing long atomic operation function
calls that spanned 2-3 lines with a short 1-line macro call.
- Don't call mi_switch() from mtx_enter_hard() when we block while trying
to obtain a sleep mutex. Calling mi_switch() would bogusly release
Giant before switching to the next process. Instead, inline most of the
code from mi_switch() in the mtx_enter_hard() function. Note that when
we finally kill Giant we can back this out and go back to calling
mi_switch().
in most of the atomic operations. Now for these operations, you can
use the normal atomic operation, you can use the operation with a read
barrier, or you can use the operation with a write barrier. The function
names follow the same semantics used in the ia64 instruction set. An
atomic operation with a read barrier has the extra suffix 'acq', due to
it having "acquire" semantics. An atomic operation with a write barrier
has the extra suffix 'rel'. These suffixes are inserted between the
name of the operation to perform and the typename. For example, the
atomic_add_int() function now has 3 variants:
- atomic_add_int() - this is the same as the previous function
- atomic_add_acq_int() - this function combines the add operation with a
read memory barrier
- atomic_add_rel_int() - this function combines the add operation with a
write memory barrier
- Add 'ptr' to the list of types that we can perform atomic operations
on. This allows one to do atomic operations on uintptr_t's. This is
useful in the mutex code, for example, because the actual mutex lock is
a pointer.
- Add two new operations for doing loads and stores with memory barriers.
The new load operations use a read barrier before the load, and the
new store operations use a write barrier after the load. For example,
atomic_load_acq_int() will atomically load an integer as well as
enforcing a read barrier.
check in the [basic.link] section of the C++ standard wrong. gcc-2.7.2.3
apparently doesn't do the check, so the bug doesn't affect RELENG_3.
PR: 16170, 21427
Submitted by: Max Khon <fjoe@lark.websci.ru> (i386 version)
Discussed with: jdp
return through doreti to handle ast's. This is necessary for the
clock interrupts to work properly.
- Change the clock interrupts on the x86 to be fast instead of threaded.
This is needed because both hardclock() and statclock() need to run in
the context of the current process, not in a separate thread context.
- Kill the prevproc hack as it is no longer needed.
- We really need Giant when we call psignal(), but we don't want to block
during the clock interrupt. Instead, use two p_flag's in the proc struct
to mark the current process as having a pending SIGVTALRM or a SIGPROF
and let them be delivered during ast() when hardclock() has finished
running.
- Remove CLKF_BASEPRI, which was #ifdef'd out on the x86 anyways. It was
broken on the x86 if it was turned on since cpl is gone. It's only use
was to bogusly run softclock() directly during hardclock() rather than
scheduling an SWI.
- Remove the COM_LOCK simplelock and replace it with a clock_lock spin
mutex. Since the spin mutex already handles disabling/restoring
interrupts appropriately, this also lets us axe all the *_intr() fu.
- Back out the hacks in the APIC_IO x86 cpu_initclocks() code to use
temporary fast interrupts for the APIC trial.
- Add two new process flags P_ALRMPEND and P_PROFPEND to mark the pending
signals in hardclock() that are to be delivered in ast().
Submitted by: jakeb (making statclock safe in a fast interrupt)
Submitted by: cp (concept of delaying signals until ast())
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
- Move all register I/O into acpi_io.c
- Move event handling into acpi_event.c
- Reorganise headers into acpivar/acpireg/acpiio
- Move find-RSDT and find-ACPI-owned-memory into acpi_machdep
- Allocate all resources (except those detailed only by AML)
as real resources. Add infrastructure that will make adding
resource support to AML code easy.
- Remove all ACPI #ifdefs in non-ACPI code
- Removed unnecessary includes
- Minor style and commenting fixes
Reviewed by: iwasaki
not work on any real hardware (or fully work on any simulator). Much more
needs to happen before this is actually functional but its nice to see
the FreeBSD copyright message appear in the ia64 simulator.
i386/isa/pcibus.c. This gets -current running again on multiple host->pci
machines after the most recent nexus commits. I had discussed this with
Mike Smith, but ended up doing it slightly differently to what we
discussed as it turned out cleaner this way. Mike was suggesting creating
a new resource (SYS_RES_PCIBUS) or something and using *_[gs]et_resource(),
but IMHO that wasn't ideal as SYS_RES_* is meant to be a global platform
property, not a quirk of a given implementation. This does use the ivar
methods but does so properly. It also now prints the physical pci bus that
a host->pci bridge (pcib) corresponds to.
