Do not use ic_macaddr as a storage for current BSSID;
it may be reused in vap creation procedure;
similar to r288619.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5513
the first device entry matching the USB vendor, product and revision
would be searched for quirks. After this patch all device entries will
be searched for quirks.
MFC after: 1 week
urtwn_set_rx_bssid_all() will allow to receive beacons only
when they are not denied by filter.
Revealed by D5474.
Tested with RTL8188CUS, HOSTAP mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5477
requesting the initial complete device descriptor and not as part of
the subsequent babble error recovery. Babble means that the received
USB packet was bigger than than configured maximum packet size. This
only affects enumeration of FULL speed USB devices which use a
bMaxPacketSize different from 8 bytes. This patch might help fix
enumeration of USB devices which exhibit USB I/O errors in dmesg
during boot.
MFC after: 1 week
- Add URTWN_WITHOUT_UCODE option (will disable any firmware specific code
when set).
- Do not exclude the driver from build when MK_SOURCELESS_UCODE is set
(URTWN_WITHOUT_UCODE will be enforced unconditionally).
- Do not abort initialization when firmware cannot be loaded;
behave like the URTWN_WITHOUT_UCODE option was set.
- Drop some unused variables from urtwn_softc structure.
Tested with RTL8188EU and RTL8188CUS in HOSTAP and STA modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4849
Use driver settable callbacks for handling of:
- core post reset
- reading actual port speed
Typically, OTG enabled EHCI cores wants setting of USBMODE register,
but this register is not defined in EHCI specification and different
cores can have it on different offset.
Also, for cores with TT extension, actual port speed must be determinable.
But again, EHCI specification not covers this so this patch provides
function for two most common variant of speed bits layout.
Reviewed by: hselasky
Differential Revision: https://reviews.freebsd.org/D5088
Redo LC calibration if temperature changed significantly since last
calibration.
Tested with RTL8188EU/RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Obtained from: NetBSD (mostly)
Differential Revision: https://reviews.freebsd.org/D4966
- Use bitmap for debug output selection.
- Add few new messages (one for URTWN_DEBUG_BEACON
and another one for URTWN_DEBUG_INTR).
- Replace an undocumented URTWN_DEBUG definition with USB_DEBUG.
Tested with RTL8188EU / RTL8188CUS in IBSS / HOSTAP modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4959
(by default it was set to 9us).
Tested with RTL8188EU / RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4535
Driver was modified to ensure it attaches properly to "marvell,orion-ehci"
node, which doesn't have error interrupt line defined. Neccessary
ofw_compat_data struct was added and probe procedure was altered.
Reviewed by: andrew, ian
Obtained from: Semihalf
Sponsored by: Stormshield
Submitted by: Bartosz Szczepanek <bsz@semihalf.com>
Differential revision: https://reviews.freebsd.org/D4369
Previously the polarity was for TTL levels, which are the reverse of RS-232.
Also add handling of the UART_PPS_INVERT_PULSE option bit in the sysctl
value, the same as was recently added to uart(4), so that people using TTL
level connections can request a logical inverting of the signal.
Use the named constants from the new dev/uart/uart_ppstypes.h for the pps
capture modes and option bits.
- Add the structure with already known fields offsets
(some of them were taken from this driver,
some (channel_plan, rf_* fields) - from TP-LINK official driver)
- Fix a typo / dehardcode a constant in RTL8192C ROM structure.
Tested with RTL8188EU, STA mode
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4274
available. As with MSI interrupts these can be disabled by setting
hw.usb.xhci.msix to 0 in the loader.
MSI-X interrupts are needed on some hardware, for example the Cavium
ThunderX only supports them, and with this we don't fall back to polling.
PR: 204378
Reviewed by: hselasky, jhb
MFC after: 1 week (after r292669)
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D4698
Tested with RTL8188EU and RTL8188CUS in STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4523
Currently, in case when npkts >= 2, RSSI and Rx radiotap fields
will be overridden by the next packet. As a result, every packet
from this chain will use the same RSSI / radiotap data.
After this change, RSSI and radiotap structure will be filled
for every frame right before ieee80211_input() call.
Tested with RTL8188EU / RTL8188CUS, STA and MONITOR modes.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4487
An implementation from rum(4) was used (it looks simpler for me).
Will be used for h/w encryption support.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4447
- Add IEEE80211_GET_SLOTTIME(ic) macro.
- Use predefined macroses to set slot time.
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4044
tables. Some drivers needed some slight re-arrangement of declarations
to accommodate this. Change the USB pnp tables slightly to allow
better compatibility with the system by moving linux driver info from
start of each entry to the end. All other PNP tables in the system
have the per-device flags and such at the end of the elements rather
that at the beginning.
Differential Review: https://reviews.freebsd.org/D3458
from 1500 to 1496 bytes. The MTU should remain at 1500, extending the
frame size as per IEEE 802.3. Adding IFCAP_VLAN_MTU to the
if_capabilities field in the smsc driver solves the problem. The
datasheet for the LAN9512 chip, section 3.2.3 states that the chip
supports the extended frame.
Submitted by: rpp@ci.com.au
MFC after: 1 week
PR: 205050
- Restore R92C_TXDW4_HWSEQ_EN bit - it is used by non-8188EU chips.
- Fix DRVRATE bit usage.
Tested with:
- RTL8188EU, STA mode.
- RTL8188CUS, STA mode.
Reviewed by: kevlo
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D4352
