result of a joined effort with parts contributed by Doug Rabson, Warner
Losh and Stefan Esser (hope I did not forget anybody). Part of the sources
is obtained from NetBSD with modifications.
This code is work in progress:
As of the time of the initial import, a loader.exe executable is built,
which can be loaded on an Alpha with NT only firmware, but no attempt is
made to switch to OSF PAL code as required to start an actual kernel.
active or not. The only sane thing we can do here is assume that if
APM is supported it might be active at some point, and bail.
In reality, even this isn't good enough; regardless of whether we support
APM or not, the system may well futz with the CPU's clock speed and throw
the TSC off. We need to stop using it for timekeeping except under
controlled circumstances. Curse the lack of a dependable high-resolution
timer.
equivalent to SYS_RES_MEMORY for x86 but for alpha, the rman_get_virtual()
address of the resource is initialised to point into either dense-mapped
or bwx-mapped space respectively, allowing direct memory pointers to be
used to device memory.
Reviewed by: Andrew Gallatin <gallatin@cs.duke.edu>
This function is called for each device for which no driver
was found.
Output is similar to the eisa_probe_nomatch() function but with the
added benefit of displaying the assigned IRQ (since PCI gives us
this information up front.)
Output is like so:
pci0: unknown card CPQ0508 (vendor=0x0e11, dev=0x0508) at 11.0 irq 9
pci0: unknown card DFZ0508 (vendor=0x10da, dev=0x0508) at 11.0 irq 9
pci0: unknown card DBL0508 (vendor=0x104c, dev=0x0508) at 11.0 irq 9
pci0: unknown card DDM0011 (vendor=0x108d, dev=0x0011) at 11.0 irq 9
I'm not happy with the 3 lines of macro cruft that got added but
I consider it a temporary annoyance as those bits will be moved to
some place where PCI, EISA and ISAPNP code will be able to use them.
(Not surprisingly, this message is longer than the code in question.)
Reviewed by: peter, dfr
a PCI memory mapped region, rman_get_bushandle() returns what happens
to be a kernel virtual address pointing to the base of the PCI shared
memory window. However this is not the behavior on all platforms:
the only thing you should do with the bushandle is pass it to the
bus_spare_read()/bus_space_write() routines. If you actually do want
the kernel virtual address of the base of the PCI memory window, you
need to use rman_get_virtual().
The problem is that at the moment, rman_get_virtual() returns a physical
address, which is bad. In order to get the kernel virtual address we
need, we have to play with it a little.
Presumeably this behavior will be changed, but in the meantime the
Tigon driver won't work. So for the moment, I'm adding a kludge to
make things happy on the alpha: the correct kernel virtual address
is calculated from the value returned by rman_get_virtual(). This
should be removed once rman_get_virtual() starts doing the right
thing.
This should make the Tigon actuall work on the alpha now.
macros) to the signal handler, for old-style BSD signal handlers as
the second (int) argument, for SA_SIGINFO signal handlers as
siginfo_t->si_code. This is source-compatible with Solaris, except
that we have no <siginfo.h> (which isn't even mentioned in POSIX
1003.1b).
An rather complete example program is at
http://www3.cons.org/cracauer/freebsd-signal.c
This will be added to the regression tests in src/.
This commit also adds code to disable the (hardware) FPU from
userconfig, so that you can use a software FP emulator on a machine
that has hardware floating point. See LINT.
ethernet controllers based on the AIC-6915 "Starfire" controller chip.
There are single port, dual port and quad port cards, plus one 100baseFX
card. All are 64-bit PCI devices, except one single port model.
The Starfire would be a very nice chip were it not for the fact that
receive buffers have to be longword aligned. This requires buffer
copying in order to achieve proper payload alignment on the alpha.
Payload alignment is enforced on both the alpha and x86 platforms.
The Starfire has several different DMA descriptor formats and transfer
mechanisms. This driver uses frame descriptors for transmission which
can address up to 14 packet fragments, and a single fragment descriptor
for receive. It also uses the producer/consumer model and completion
queues for both transmit and receive. The transmit ring has 128
descriptors and the receive ring has 256.
This driver supports both FreeBSD/i386 and FreeBSD/alpha, and uses newbus
so that it can be compiled as a loadable kernel module. Support for BPF
and hardware multicast filtering is included.
Translated from: a similar fix in ufs_readwrite.c rev.1.61.
Don't forget to set DE_ACCESS for short reads.
Check for invalid (negative) offsets before checking for reads of
0 bytes, as in ufs, although checking for invalid offsets at all
is probably a bug.
Set IN_ACCESS for successful reads of 0 bytes (except for requests to
read 0 bytes). This was broken in rev.1.42.
PR: misc/10148
Don't set IN_ACCESS for requests to read 0 bytes.
Don't set IN_ACCESS for unsuccessful reads.
Change "void *" to "volatile TYPE *", improving type safety
and eliminating some warnings (e.g., mp_machdep.c rev 1.106).
cpufunc.h:
Eliminate setbits. As defined, it's not precisely correct;
and it's redundant. (Use atomic_set_int instead.)
ipl_funcs.c:
Use atomic_set_int instead of setbits.
systm.h:
Include atomic.h.
Reviewed by: bde
the loop and not set an error, so we would then try to access an invalid
mbuf...
PR: 12780
Submitted by: bright@rush.net aka zb^3
a new record in length a pr was open... only about a half hour...
critical mbuf fields to sane values. Simplify the use of ETHER_ALIGN to
enforce payload alignment, and turn it on on the x86 as well as alpha
since it helps with NFS which wants the payload to be longword aligned
even though the hardware doesn't require it.
This fixes a problem with the ti driver causing an unaligned access trap
on the Alpha due to m_adj() sometimes not setting the alignment correctly
because of incomplete mbuf initialization.
the driver_t declaration should be "skc" not "sk". Technically, "skc"
is the parent PCI device (the SysKonnect GEnesis controller) and "sk0"
and "sk1" are the network interfaces that get attached to it.
