If MAKEOBJDIRPREFIX is set, use it for default OBJROOT.
If MAKEOBJDIR is empty or not a suitable value (no '/')
set a default that works.
Reviewed by: bdrewery
Coredump notes depend on being able to invoke dump routines twice; once
in a dry-run mode to get the size of the note, and another to actually
emit the note to the corefile.
When a note helper emits a different length section the second time
around than the length it requested the first time, the kernel produces
a corrupt coredump.
NT_PROCSTAT_FILES output length, when packing kinfo structs, is tied to
the length of filenames corresponding to vnodes in the process' fd table
via vn_fullpath. As vnodes may move around during dump, this is racy.
So:
- Detect badly behaved notes in putnote() and pad underfilled notes.
- Add a fail point, debug.fail_point.fill_kinfo_vnode__random_path to
exercise the NT_PROCSTAT_FILES corruption. It simply picks random
lengths to expand or truncate paths to in fo_fill_kinfo_vnode().
- Add a sysctl, kern.coredump_pack_fileinfo, to allow users to
disable kinfo packing for PROCSTAT_FILES notes. This should avoid
both FILES note corruption and truncation, even if filenames change,
at the cost of about 1 kiB in padding bloat per open fd. Document
the new sysctl in core.5.
- Fix note_procstat_files to self-limit in the 2nd pass. Since
sometimes this will result in a short write, pad up to our advertised
size. This addresses note corruption, at the risk of sometimes
truncating the last several fd info entries.
- Fix NT_PROCSTAT_FILES consumers libutil and libprocstat to grok the
zero padding.
With suggestions from: bjk, jhb, kib, wblock
Approved by: markj (mentor)
Relnotes: yes
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3548
go asking what debug flags to set for GEOM to make it work. Advice
them to use gpart(8) instead.
Something similar should probably done with disklabel,
but I need to rewrite the disklabel examples first.
Reviewed by: wblock@
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3315
Go ahead and defined -D_STANDALONE for all targets (only strictly
needed for some architecture, but harmless on those it isn't required
for). Also add -msoft-float to all architectures uniformly rather
that higgley piggley like it is today.
Differential Revision: https://reviews.freebsd.org/D3496
only gpiobus configured via FDT is supported. Bus enumeration is
supported. Devices are created for each device found. 1-Wire
temperature controllers are supported, but other drivers could be
written. Temperatures are polled and reported via a sysctl. Errors
are reported via sysctl counters. Mis-wired bus detection is included
for more trouble shooting. See ow(4), owc(4) and ow_temp(4) for
details of what's supported and known issues.
This has been tested on Raspberry Pi-B, Pi2 and Beagle Bone Black
with up to 7 devices.
Differential Revision: https://reviews.freebsd.org/D2956
Relnotes: yes
MFC after: 2 weeks
Reviewed by: loos@ (with many insightful comments)
The crop/drop-ovl fragment scrub modes are not very useful and likely to confuse
users into making poor choices.
It's also a fairly large amount of complex code, so just remove the support
altogether.
Users who have 'scrub fragment crop|drop-ovl' in their pf configuration will be
implicitly converted to 'scrub fragment reassemble'.
Reviewed by: gnn, eri
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D3466
To make it easier to understand how Capsicum interacts with linkat() and
renameat(), rename the rights to CAP_{LINK,RENAME}AT_{SOURCE,TARGET}.
This also addresses a shortcoming in Capsicum, where it isn't possible
to disable linking to files stored in a directory. Creating hardlinks
essentially makes it possible to access files with additional rights.
Reviewed by: rwatson, wblock
Differential Revision: https://reviews.freebsd.org/D3411
remove duplicates. We cannot sort SUBDIR because many Makefiles
have .WAIT in the list which is strongly ordering. Rather than
try to second guess when to sort and when to not sort depending
on .WAIT being in the list, just remove duplicates.
armv6. It's too ambiguous. We do use the softfp ABI for the moment on
armv6, but we allow floating point register use (and the compilers
will generate it). This is too ambiguous to use it as a decider for
which algorithms to use on the platform. Err on the side of caution
and not define it.
Submitted by: ian@
Reviewed by: andrew@
float targets. It is added for booke on powerpc and all arm with hf in
the string. Also add arm to all arm builds and armv6 to armv6 and
newer builds.
PR: 202641
I/OAT is also referred to as Crystal Beach DMA and is a Platform Storage
Extension (PSE) on some Intel server platforms.
This driver currently supports DMA descriptors only and is part of a
larger effort to upstream an interconnect between multiple systems using
the Non-Transparent Bridge (NTB) PSE.
For now, this driver is only built on AMD64 platforms. It may be ported
to work on i386 later, if that is desired. The hardware is exclusive to
x86.
Further documentation on ioat(4), including API documentation and usage,
can be found in the new manual page.
Bring in a test tool, ioatcontrol(8), in tools/tools/ioat. The test
tool is not hooked up to the build and is not intended for end users.
Submitted by: jimharris, Carl Delsey <carl.r.delsey@intel.com>
Reviewed by: jimharris (reviewed my changes)
Approved by: markj (mentor)
Relnotes: yes
Sponsored by: Intel
Sponsored by: EMC / Isilon Storage Division
Differential Revision: https://reviews.freebsd.org/D3456
Provide and document the RANDOM_ENABLE_UMA option.
Change RANDOM_FAST to RANDOM_UMA to clarify the harvesting.
Remove RANDOM_DEBUG option, replace with SDT probes. These will be of
use to folks measuring the harvesting effect when deciding whether to
use RANDOM_ENABLE_UMA.
Requested by: scottl and others.
Approved by: so (/dev/random blanket)
Differential Revision: https://reviews.freebsd.org/D3197
CoDel is a parameterless queue discipline that handles variable bandwidth
and RTT.
It can be used as the single queue discipline on an interface or as a sub
discipline of existing queue disciplines such as PRIQ, CBQ, HFSC, FAIRQ.
Differential Revision: https://reviews.freebsd.org/D3272
Reviewd by: rpaulo, gnn (previous version)
Obtained from: pfSense
Sponsored by: Rubicon Communications (Netgate)
This driver allows read the software reset switch state and control the
status LEDs.
The GPIO pins have their direction (input/output) locked down to prevent
possible short circuits.
Note that most people get a reset button that is a hardware reset. The
software reset button is available on boards from Netgate.
Sponsored by: Rubicon Communications (Netgate)
For most cases they are equivalent, but BINUTILS_BOOTSTRAP is a
BROKEN_OPTION on arm64 as the in-tree GNU binutils do not support it,
so we need a separate internal flag for ELF Tool Chain.
Reviewed by: andrew, brooks
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3381
if desired.
Retire randomdev_none.c and introduce random_infra.c for resident
infrastructure. Completely stub out random(4) calls in the "without
DEV_RANDOM" case.
Add RANDOM_LOADABLE option to allow loadable Yarrow/Fortuna/LocallyWritten
algorithm. Add a skeleton "other" algorithm framework for folks
to add their own processing code. NIST, anyone?
Retire the RANDOM_DUMMY option.
Build modules for Yarrow, Fortuna and "other".
Use atomics for the live entropy rate-tracking.
Convert ints to bools for the 'seeded' logic.
Move _write() function from the algorithm-specific areas to randomdev.c
Get rid of reseed() function - it is unused.
Tidy up the opt_*.h includes.
Update documentation for random(4) modules.
Fix test program (reviewers, please leave this).
Differential Revision: https://reviews.freebsd.org/D3354
Reviewed by: wblock,delphij,jmg,bjk
Approved by: so (/dev/random blanket)
- Add
nvlist_{add,get,take,move,exists,free}_{number,bool,string,nvlist,
descriptor} functions.
- Add support for (un)packing arrays.
- Add the nvl_array_next field to the nvlist structure.
If an array is added by the nvlist_{move,add}_nvlist_array function
this field will contains next element in the array.
- Add the nitems field to the nvpair and nvpair_header structure.
This field contains number of elements in the array.
- Add special flag (NV_FLAG_IN_ARRAY) which is set if nvlist is a part of
an array.
- Add special type (NV_TYPE_NVLIST_ARRAY_NEXT).This type is used only
on packing/unpacking.
- Add new API for traversing arrays (nvlist_get_array_next).
- Add the nvlist_get_pararr function which combines the
nvlist_get_array_next and nvlist_get_parent functions. If nvlist is in
the array it will return next element from array. If nvlist is last
element in array or it isn't in array it will return his
container (parent). This function should simplify traveling over nvlist.
- Add tests for new features.
- Add documentation for new functions.
- Add my copyright.
- Regenerate the sys/cddl/compat/opensolaris/sys/nvpair.h file.
PR: 191083
Reviewed by: allanjude (doc)
Approved by: pjd (mentor)
As the name indicates, these are flags to pass to nm(1). The newer
binutils have a plugin mechanism so, to build something with LLVM's
LTO, we need to pass flags to nm(1). This commit also extends
lorder(1) to pass NMFLAGS to nm(1).
operation as a write barrier. That description has never been correct,
and it has caused confusion. An acquire operation orders writes as well
as reads, and a release operation orders reads as well as writes.
Also, explicitly say that a thread doesn't see its own accesses being
reordered. The reordering of a thread's accesses is only (potentially)
visible to another thread. Thus, memory barriers need only be used to
control the ordering of accesses between threads, not within a thread.
Reviewed by: bde, kib
Discussed with: jhb
MFC after: 1 week
