Now that bhyve(8) supports UART, bvmconsole and bvmdebug are no longer needed.
This also removes the '-b' and '-g' flag from bhyve(8). These two flags were
marked deprecated in r368519.
Reviewed by: grehan, kevans
Approved by: kevans (mentor)
Differential Revision: https://reviews.freebsd.org/D27490
Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
No functional change intended.
change 0 means success and non-zero means failure.
This also helps to eliminate VMEXIT_POWEROFF and VMEXIT_RESET as return values
from VM-exit handlers.
CR: D480
Reviewed by: grehan, jhb
the UART FIFO.
The emulation is constrained in a number of ways: 64-bit only, doesn't check
for all exception conditions, limited to i/o ports emulated in userspace.
Some of these constraints will be relaxed in followup commits.
Requested by: grehan
Reviewed by: tychon (partially and a much earlier version)
- Implement the PM1_EVT and PM1_CTL registers required by ACPI.
The PM1_EVT register is mostly a dummy as bhyve doesn't support any
of the hardware-initiated events. The only bit of PM1_CNT that is
implemented are the sleep request bits (SPL_EN and SLP_TYP) which
request a graceful power off for S5. In particular, for S5, bhyve
exits with a non-zero value which terminates the loop in vmrun.sh.
- Emulate the Reset Control register at I/O port 0xcf9 and advertise
it as the reset register via ACPI.
- Advertise an _S5 package.
- Extend the in/out interface to allow an in/out handler to request
that the hypervisor trigger a reset or power-off.
- While here, note that all vCPUs in a guest support C1 ("hlt").
Reviewed by: neel (earlier version)
to a virtual machine then we implicitly create COM1 and COM2 ISA devices.
Prior to this change the only way of attaching a COM port to the virtual
machine was by presenting it as a PCI device that is mapped at the legacy
I/O address 0x3F8 or 0x2F8.
There were some issues with the original approach:
- It did not work at all with UEFI because UEFI will reprogram the PCI device
BARs and remap the COM1/COM2 ports at non-legacy addresses.
- OpenBSD GENERIC kernel does not create a /dev/console because it expects
the uart device at the legacy 0x3F8/0x2F8 address to be an ISA device.
- It was functional with a FreeBSD guest but caused the console to appear
on /dev/ttyu2 which was not intuitive.
The uart emulation is now independent of the bus on which it resides. Thus it
is possible to have uart devices on the PCI bus in addition to the legacy
COM1/COM2 devices behind the LPC bus.
The command line option to attach ISA COM1/COM2 ports to a virtual machine is
"-s <bus>,lpc -l com1,stdio".
The command line option to create a PCI-attached uart device is:
"-s <bus>,uart[,stdio]"
The command line option to create PCI-attached COM1/COM2 device is:
"-S <bus>,uart[,stdio]". This style of creating COM ports is deprecated.
Discussed with: grehan
Reviewed by: grehan
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
M share/examples/bhyve/vmrun.sh
AM usr.sbin/bhyve/legacy_irq.c
AM usr.sbin/bhyve/legacy_irq.h
M usr.sbin/bhyve/Makefile
AM usr.sbin/bhyve/uart_emul.c
M usr.sbin/bhyve/bhyverun.c
AM usr.sbin/bhyve/uart_emul.h
M usr.sbin/bhyve/pci_uart.c
M usr.sbin/bhyve/pci_emul.c
M usr.sbin/bhyve/inout.c
M usr.sbin/bhyve/pci_emul.h
M usr.sbin/bhyve/inout.h
AM usr.sbin/bhyve/pci_lpc.c
AM usr.sbin/bhyve/pci_lpc.h
- Respect the MEMEN and PORTEN bits in the command register
- Allow the guest to reprogram the address decoded by the BAR
Submitted by: Gopakumar T
Obtained from: NetApp
run as a 1/2 CPU guest on an 8.1 bhyve host.
bhyve/inout.c
inout.h
fbsdrun.c
- Rather than exiting on accesses to unhandled i/o ports, emulate
hardware by returning -1 on reads and ignoring writes to unhandled
ports. Support the previous mode by allowing a 'strict' parameter
to be set from the command line.
The 8.1 guest kernel was vastly cut down from GENERIC and had no
ISA devices. Booting GENERIC exposes a massive amount of random
touching of i/o ports (hello syscons/vga/atkbdc).
bhyve/consport.c
dev/bvm/bvm_console.c
- implement a simplistic signature for the bvm console by returning
'bv' for an inw on the port. Also, set the priority of the console
to CN_REMOTE if the signature was returned. This works better in
an environment where multiple consoles are in the kernel (hello syscons)
bhyve/rtc.c
- return 0 for the access to RTC_EQUIPMENT (yes, you syscons)
amd64/vmm/x86.c
x86.h
- hide a bunch more CPUID leaf 1 bits from the guest to prevent
cpufreq drivers from probing.
The next step will be to move CPUID handling completely into
user-space. This will allow the full spectrum of changes from
presenting a lowest-common-denominator CPU type/feature set, to
exposing (almost) everything that the host can support.
Reviewed by: neel
Obtained from: NetApp
vmm.ko - kernel module for VT-x, VT-d and hypervisor control
bhyve - user-space sequencer and i/o emulation
vmmctl - dump of hypervisor register state
libvmm - front-end to vmm.ko chardev interface
bhyve was designed and implemented by Neel Natu.
Thanks to the following folk from NetApp who helped to make this available:
Joe CaraDonna
Peter Snyder
Jeff Heller
Sandeep Mann
Steve Miller
Brian Pawlowski
