creating delayed write buffers belonging to the reclaimed vnode. Put
the buffer cleanup code after inactivation.
Add asserts that ensure that buffer queues are empty and add BO_DEAD
flag for bufobj to check that no buffers are added after the cleanup.
BO_DEAD is only used by INVARIANTS-enabled kernels.
Reported and tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Verify that the block pointer is structurally valid, before attempting to
read it in. It can only be invalid in the case of a ZFS bug, but this
change will help identify such bugs in a more transparent way, by
panic'ing with a relevant message, rather than indexing off the end of an
array or something.
Illumos issue:
5349 verify that block pointer is plausible before reading
MFC after: 2 weeks
Reduce scrub activities when system there is enough dirty data, namely when
dirty data is more than zfs_vdev_async_write_active_min_dirty_percent (once
we start to increase the number of concurrent async writes).
While there also correct rounding error which would make scrub end up
pausing for (zfs_txg_timeout + 1) seconds instead of the desired
zfs_txg_timeout seconds.
Illumos issue:
5351 scrub goes for an extra second each txg
5352 scrub should pause when there is some dirty data
MFC after: 2 weeks
If zio_checksum_error() returns other than ECKSUM (e.g. EINVAL), it does not
fill in the "zio_bad_cksum_t *info" parameter. Caller should not attempt to
use it in this case.
Illumos issue:
5348 zio_checksum_error() only fills in info if ECKSUM
MFC after: 2 weeks
If a dnode has a spill block and there is an error while accessing
a data block then traverse_dnode() loses information about that error
and returns a status of visiting the spill block.
This issue is discovered by Spectra Logic.
Illumos issue:
5311 traverse_dnode may report success when it should not
Original author: gibbs
MFC after: 2 weeks
for counter mode), and AES-GCM. Both of these modes have been added to
the aesni module.
Included is a set of tests to validate that the software and aesni
module calculate the correct values. These use the NIST KAT test
vectors. To run the test, you will need to install a soon to be
committed port, nist-kat that will install the vectors. Using a port
is necessary as the test vectors are around 25MB.
All the man pages were updated. I have added a new man page, crypto.7,
which includes a description of how to use each mode. All the new modes
and some other AES modes are present. It would be good for someone
else to go through and document the other modes.
A new ioctl was added to support AEAD modes which AES-GCM is one of them.
Without this ioctl, it is not possible to test AEAD modes from userland.
Add a timing safe bcmp for use to compare MACs. Previously we were using
bcmp which could leak timing info and result in the ability to forge
messages.
Add a minor optimization to the aesni module so that single segment
mbufs don't get copied and instead are updated in place. The aesni
module needs to be updated to support blocked IO so segmented mbufs
don't have to be copied.
We require that the IV be specified for all calls for both GCM and ICM.
This is to ensure proper use of these functions.
Obtained from: p4: //depot/projects/opencrypto
Relnotes: yes
Sponsored by: FreeBSD Foundation
Sponsored by: NetGate
ipsec6_in_reject() does the same things, also it counts policy violation
errors.
Do IPSEC check in the ip6_forward() after addresses checks.
Also use ip6_ipsec_fwd() to make code similar to IPv4 implementation.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
ipsec_getpolicybyaddr()
ipsec4_checkpolicy()
ip_ipsec_output()
ip6_ipsec_output()
The only flag used here was IP_FORWARDING.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
and make its prototype similar to ipsec6_process_packet.
The flags argument isn't used here, tunalready is always zero.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
Remove check for presence PACKET_TAG_IPSEC_IN_DONE mbuf tag from
ip_ipsec_fwd(). PACKET_TAG_IPSEC_IN_DONE tag means that packet is
already handled by IPSEC code. This means that before IPSEC processing
it was destined to our address and security policy was checked in
the ip_ipsec_input(). After IPSEC processing packet has new IP
addresses and destination address isn't our own. So, anyway we can't
check security policy from the mbuf tag, because it corresponds
to different addresses.
We should check security policy that corresponds to packet
attributes in both cases - when it has a mbuf tag and when it has not.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
security policy. The changed block of code in ip*_ipsec_input() is
called when packet has ESP/AH header. Presence of
PACKET_TAG_IPSEC_IN_DONE mbuf tag in the same time means that
packet was already handled by IPSEC and reinjected in the netisr,
and it has another ESP/AH headers (encrypted twice?).
Since it was already processed by IPSEC code, the AH/ESP headers
was already stripped (and probably outer IP header was stripped too)
and security policy from the tdb_ident was applied to those headers.
It is incorrect to apply this security policy to current headers.
Also make ip_ipsec_input() prototype similar to ip6_ipsec_input().
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
PACKET_TAG_IPSEC_OUT_CRYPTO_NEEDED mbuf tags. They aren't used in FreeBSD.
Instead check presence of PACKET_TAG_IPSEC_OUT_DONE mbuf tag. If it
is found, bypass security policy lookup as described in the comment.
PACKET_TAG_IPSEC_OUT_DONE tag added to mbuf when IPSEC code finishes
ESP/AH processing. Since it was already finished, this means the security
policy placed in the tdb_ident was already checked. And there is no reason
to check it again here.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
By default Xen binds all event channels to vCPU#0, and FreeBSD only shuffles
the interrupt sources once, at the end of the boot process. Since new event
channels might be created after this point (because new devices or backends
are added), try to automatically shuffle them at creation time.
This does not affect VIRQ or IPI event channels, that are already bound to a
specific vCPU as requested by the caller.
Sponsored by: Citrix Systems R&D
Mask the event channel source before trying to bind it to a CPU, this
prevents stray interrupts from firing while assigning them and hitting the
KASSERT in xen_intr_handle_upcall.
Sponsored by: Citrix Systems R&D
This allows the Grant-table code to attach directly to the xenpv bus,
allowing us to remove the grant-table initialization done in xenpv.
Sponsored by: Citrix Systems R&D
Mave the grant table code into the dev/xen folder in preparation for turning
it into a device using the newbus interface. This is just code motion, no
functional changes.
Sponsored by: Citrix Systems R&D
can't do a timeout bigger than 15 seconds. The code wasn't checking for
this and because bitmasking was involved the requested timeout was
basically adjusted modulo-16. That led to things like a 128 second
timeout actually being a 9 second timeout, which accidentally worked fine
until watchdogd was changed to only pet the dog once every 10 seconds.
When running as a Xen PVH Dom0 we need to add custom buses that override
some of the functionality present in the ACPI PCI Bus and the PCI Bus. We
currently override the ACPI PCI Bus, but not the PCI Bus, so add a new
override for the PCI Bus and share the generic functions between them.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
conf/files.amd64:
- Add the new files.
x86/xen/xen_pci_bus.c:
- Generic file that contains the PCI overrides so they can be used by the
several PCI specific buses.
xen/xen_pci.h:
- Prototypes for the generic overried functions.
dev/xen/pci/xen_pci.c:
- Xen specific override for the PCI bus.
dev/xen/pci/xen_acpi_pci.c:
- Xen specific override for the ACPI PCI bus.
o Move similar block/networking methods to common file
o Follow r275640 and correct MMIO registers width
o Pass value to MMIO platform_note method.
Sponsored by: DARPA, AFRL
Overrunning buffer pointed to by (caddr_t)&oip->i_db[0] of 48 bytes by
passing it to a function which accesses it at byte offset 59 using
argument 60UL.
The issue was inherited from an older FFS implementation and
fixed there with by merging UFS2 in r98542. We follow the
FFS fix.
Discussed with: bde
CID: 1007665
MFC after: 3 days
If the SCI is remapped to a non-ISA global interrupt notify the ACPI
subsystem about the override.
Reported by: David P. Discher <dpd@dpdtech.com>
Sponsored by: Citrix Systems R&D
There are two main parts to get it to work, 1) most of the register
accesses need to be word sized, other than the config register which
needs to be byte aligned, and 2) we don't need the platform driver
for this to work on the Foundation Model, allow it to be NULL.
Differential Revision: https://reviews.freebsd.org/D1240
Reviewed by: bryanv
Sponsored by: The FreeBSD Foundation
Since VFS does not/cannot stop writes, sync might run indefinitely, or
be a wrong thing to do at all. E. g. NFS ignores VFS_SYNC() for
forced unmounts, since non-responding server does not allow sync to
finish. On the other hand, filesystems can and do stop writes using
fs-specific facilities, and should already fully flush caches in
VFS_UNMOUNT() due to the race.
Adjust msdosfs tp sync in unmount for forced call, to accomodate the
new behaviour. Note that it is still racy, since writes are not
stopped.
Discussed with: avg, bjk, mckusick
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
to be called before suspension and after resume, correspondingly. The
syncer_suspend() ensures that all filesystems dirty data and metadata
are saved to the permanent storage, and stops kernel threads which
might modify filesystems. The syncer_resume() restores stopped
threads.
For now, only syncer is stopped. This is needed, because each sync
loop causes superblock updates for UFS.
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
the vnode owning the buffer is not locked. More, it cannot be locked
safely, since getnewbuf_reuse_bp() is called from newbuf(), and some
other vnode is already locked, for which reused buffer will be
reassigned.
As the consequence, reclamation of the owning vnode could go in
parallel, in particular, the call to vnode_destroy_vobject(), which
deallocates the vm object and zeroes the v_bufobj->bo_object. Note
that the pages wired by the buffer are left wired and can be safely
freed by the vfs_vmio_release() without the need for the vm object
lock. Also, seeing stale pointer to the v_object is safe due to vm
object type stability.
Check for bo_bufobj != NULL and cache the value in local variable to
avoid trying to lock NULL vm object.
Reported and tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
