have been in the code all along, but were masked by having a fifo depth of
one byte at the hardware level, so everything kinda worked by accident.
The hardware interrupts when the TX fifo is half empty, so set
sc->sc_txfifosz to 8 bytes (half the hardware fifo size) to match. This
eliminates dropped characters on output.
Restructure the read loop to consume all the bytes in the fifo by using
the "rx fifo empty" bit of the flags register rather than the "rx ready"
bit of the interrupt status register. The rx-ready interrupt is cleared
when the number of bytes in the fifo fall below the interrupt trigger
level, leaving the fifo half full every time receive routine was called.
Now it loops until the fifo is completely empty every time (including
when the function is called due to a receive timeout as well as for
fifo-full).
Dan Krejsa reports a potential memory leak in an fts_build error case,
detected by Coverity. (It doesn't seem to show up in Coverity Scan, so I
don't have a CID to point to.)
I don't know whether it is actually possible to arrive in this case with a
non-empty 'head' list. The cost is low, though. One additional branch in a
terminal error case isn't the end of the world.
PR: 217125
Submitted by: Dan Krejsa <dan.krejsa at gmail.com>
Some of the changes I introduced to use .ALLSRC were correct in spirit,
but incorrect in reality -- in particular, ../Makefile.inc hadn't been
pulled in via bsd.init.mk (via bsd.lib.mk, bsd.prog.mk), so the value
of .ALLSRC (evaluated immediately) was empty. .include bsd.init.mk
explicitly so we can be certain that the values used as dependencies in
the targets are defined when the target recipe has been evaluated.
Reminder: thou shalt separate out separate functional changes before
committing them.
(YUGE) Pointyhat to: ngie
In collaboration with: bdrewery
MFC after: 1 month
Reported by: Jenkins, cy, ler, O. Hartmann, Michael Butler
Sponsored by: Dell EMC Isilon
RPi3 cpufreq is more like that on RPi2. Setting arm frequency
above min (say, "sysctl hw.cpufreq.arm_freq=600000001") turns on
turbo mode, and the firmware automatically raises voltage, sets
frequency to max 1200MHz, and throttle when overheat, etc.
Swap if/else parts and use SOC_BCM2835 def so RPi3 can share the
same cpufreq logic as RPi2, instead of falling to that for RPi.
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9640
80486 production was stopped by Intel on September 2007. Dropping the 486
configuration option from the GENERIC kernel improves performance
slightly.
Removing I486_CPU is consistent at this time: we don't support any
processor without a FPU and the PC-98 arch, which frequently involved i486
CPUs, is also gone so we don't test such platforms anymore.
Relnotes: yes
MFC after: 2 weeks
https://reviews.freebsd.org/D9879
Modern GCC and Clang simply ignore the qualifier, while the old base GCC
produces a warning (treated as an error in the kernel build).
Approved by: cem
MFC after: 5 days
This simplifies make logic/output
While here, remove bogus CFLAGS which look for headers in cddl/lib/libumem.
There aren't any source files there (just Makefiles)
MFC after: 1 month
Sponsored by: Dell EMC Isilon
This is being done as a precursor for work needed to annontate failing
testcases with clang 4.0+.
MFC after: 1 week
PR: 217528
Sponsored by: Dell EMC Isilon
Linuxulator is x86 only.
The only notable differences in algnment for an LP64 64-bit system
when compared to a 32-bit system is an eight or large byte types
alignment.
MFC after: 1 month
it in emergency in sc_cnputc().
Locking fixes in sc_cnputc() previously turned off normal output in
near-deadlock conditions and added deferred output which might never
be completed. Emergency output goes to the frame buffer using
sufficiently atomic non-blocking writes if the console is in text
mode (in graphics mode, nothing is done, modulo races setting the
graphics mode bit). Screen updates overwrite the emergency output
if the emergency condition clears enough to reach them.
ec_putc() also works for "early" console output in normal x86 text
mode as soon as this mode is initialized (if ever). This uses a
hard-coded x86 frame buffer address before cninit() and a hopefully
MI address after cninit(). But non-x86 is more likely to not support
text mode, when ec_putc() will be null. ec_putc() has no dependencies
of syscons before cninit(), and only has them later to track syscons'
mode changes. This commit doesn't attach ec_putc() for early use.
To test emergency use, put a breakpoint in central syscons output code
like sc_puts() and do some user output. The system used to race or
deadlock in ddb output soon after entry to ddb. The locking fixes
deferred the output until after leaving ddb, so ddb was unusable and
you had to try typing c[ontinue] blindly until it exited, or better use
a serial console in parallel. Now the output goes to a window in the
middle 2/3 of the screen. Scrolling is circular and there is no cursor,
but otherwise ec_putc() provides full dumb terminal functionality and
very fast output that hides artificates from dumb overwrites.
My attempt to correct the sender/receiver behavior was incorrect.
The source port of the sender for forwarded datagrams is filtered
with -a, and my change in r314585 didn't clarify that point at all.
Wording is based on suggestion by hrs.
MFC after: 28 days
X-MFC with: r314563, r314585
Reported by: hrs
In collaboration with: hrs, rgrimes
Sponsored by: Dell EMC Isilon
by the CPU number.
This was originally for debugging near-deadlock conditions where
multiple CPUs either deadlock or scramble each other's output trying
to report the problem, but I found it interesting and sometimes
useful for ordinary kernel messages. Ordinary kernel messages
shouldn't be interleaved, but if they are then the colorization
makes them readable even if the interleaving is for every character
(provided the CPU printing each message doesn't change).
The default colors are 8-15 starting at 15 (bright white on black)
for CPU 0 and repeating every 8 CPUs. This works best with 8 CPUs.
Non-bright colors and nonzero background colors need special
configuration to avoid unreadable and ugly combinations so are not
configured by default. The next bright color after 15 is 8 (bright
black = dark gray) is not very readable but is the only other color
used with 2 CPUs. After that the next bright color is 9 (bright
blue) which is not much brighter than bright black, but is used with
3+ CPUs. Other bright colors are brighter.
Colorization is configured by default so that it gets tested. It can
only be turned off by configuring SC_KERNEL_CONS_ATTR to anything other
than FG_WHITE. After booting, all colors can be changed using the
syscons.kattr sysctl. This is a SYSCTL_OPAQUE, and no utility is
provided to change it (sysctl only displays it).
The default colors work in all VGA modes that I could test. In 2-color
graphics modes, all 8 bright colors are displayed as bright white, so
the colorization has no effect, but anything with a nonzero background
gives white on white unless the foreground is zero. I don't have an
mono or VGA grayscale hardware to test on. Support for mono mode seems
to have never worked right in syscons (I think bright white gives white
underline with either bold or bright), but VGA grayscale should work
better than 2-color graphics.
by usually being double-spaced due to auto-wrap at column 80.
r212771 increased width of the hostname field from 12 to 25. This was
supposed to allow for 80-column output with all 3 load averages taking
5 characters each, but it actually gave width exactly 80 and thus worse
than useless auto-wrap in that case. 3 wide load average fields are
unusual, but later expansion of another field gave the auto-wrap with
just 2 wide load average fields.
Change to dynamic field widths for all fields except the uptime. This
also fixes the formatting of high (above 9999) user counts and not
very high (above 9.99) load averages. The formatting for numbers now
breaks at 99999.99, but scientific notation should be used starting
well below that.
The field width for the uptime remains hard-coded to work consistently
for uptimes less than 10000 days, but this gives too much space for
small uptimes. Punctuation between fields could be improved in many
ways, for example by removing it.
I imagine that the module would be useful only to a very limited number
of developers, so that's my excuse for not writing any documentation.
On a more serious note, please see DRAM Error Injection section of BKDGs
for families 10h - 16h. E.g. section 2.13.3.1 of BKDG for AMD Family 15h
Models 00h-0Fh Processors.
Many thanks to kib for his suggestions and comments.
Discussed with: kib
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D9824
Currently the feature is implemented only for a subset of errors
reported via Bank 4. The subset includes only DRAM-related errors.
The new code builds upon and reuses the Intel CMC (Correctable MCE
Counters) support code. However, the AMD feature is quite different
and, unfortunately, much less regular.
For references please see AMD BKDGs for models 10h - 16h.
Specifically, see MSR0000_0413 NB Machine Check Misc (Thresholding)
Register (MC4_MISC0).
http://developer.amd.com/resources/developer-guides-manuals/
Reviewed by: jhb
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D9613
We may fail to reset the %CPU tracking window if a thread does not run
for over half of the ticks rollover period, resulting in a bogus %CPU
value for the thread until ticks fully rolls over. Handle this by comparing
the unsigned difference ticks - ts_ltick with SCHED_TICK_TARG instead.
Reviewed by: cem, jeff
MFC after: 1 week
Sponsored by: Dell EMC Isilon
CAM_UNLOCKED is internal flag and cannot correctly be set by userland.
Return EINVAL from CAMIOCOMMAND and CAMIOQUEUE if it is set.
Also fix leaks in some of the error paths for CAMIOQUEUE.
PR: 215356
Reviewed by: ken, mav
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D9869
in valuestate array.
When opcode has size equal to ipfw_insn_u32, this means that it should
additionally match value specified in d[0] with table entry value.
ipfw_table_lookup() returns table value index, use TARG_VAL() macro to
convert it to its value. The actual 32-bit value stored in the tag field
of table_value structure, where all unspecified u32 values are kept.
PR: 217262
Reviewed by: melifaro
MFC after: 1 week
Sponsored by: Yandex LLC
test suite
This change does the following:
- Introduces symmetry in the test inputs/outputs by adding the exit
code to the files. This simplified the test driver notably by
requiring less filename/test name manipulation.
- Adds a test driver for the testcases added in r313544, patterned
after bin/sh/tests/functional_test.sh . The driver calls indent as
noted in r313544, with an exception: The $FreeBSD$ RCS keyword's
expansion is reindented with indent, which means that the output
differs from the expected output. Thus, all lines with $FreeBSD$
in them are deleted on the fly, both in the input file and the
output file.
The test inputs/outputs are copied to the kyua sandbox before the
test is run as the pathing in some of the files relies on pathing
normalized to the current directory (copying the files is the
easiest way to resolve the issue).
Approved by: pstef (maintainer)
Reviewed by: pstef
X-MFC with: r313544
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9682
- Delete empty Li macro uses [1]. This removes some spaces between
the optional command/subcommand arguments.
- Attempt to clarify "show lock" subcommand by being more
terse/direct. This addresses an issue with a contraction [2].
MFC after: 1 week
Reported by: make manlint [1], igor [2]
Reviewed by: wblock
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D9858
- Optimise the RCU implementation to not allocate and free
ck_epoch_records during runtime. Instead allocate two sets of
ck_epoch_records per CPU for general purpose use. The first set is
only used for reader locks and the second set is only used for
synchronization and barriers and is protected with a regular mutex to
prevent simultaneous issues.
- Move the task structure away from the rcu_head structure and into
the per-CPU structures. This allows the size of the rcu_head structure
to be reduced down to the size of two pointers.
- Fix a bug where the linux_rcu_barrier() function only waited for one
per-CPU epoch record to be completed instead of all.
- Use a critical section or a mutex to protect ck_epoch_begin() and
ck_epoch_end() depending on RCU or SRCU type. All the ck_epoch_xxx()
functions, except ck_epoch_register(), ck_epoch_unregister() and
ck_epoch_recycle() are not re-entrant and needs a critical section or
a mutex to operate in the LinuxKPI, after inspecting the CK
implementation of the above mentioned functions. The simultaneous
issues arise from per-CPU epoch records being shared between multiple
threads depending on the amount of taskswitching and how many threads
are involved with the RCU and SRCU operations.
- Properly free all epoch records by using safe list traversal at
LinuxKPI module unload. It turns out the ck_epoch_recycle() always
have the records on an internal list and use a flag in the epoch
record to track allocated and free entries. This would lead to use
after free during module unload.
- Remove redundant synchronize_rcu() call from the
linux_compat_uninit() function. Let the linux_rcu_runtime_uninit()
function do the final rcu_barrier() instead.
MFC after: 1 week
Sponsored by: Mellanox Technologies
