- For transactions of 0 length, us a non-residual checking CCB type.
- Preserve command status if our interrupt handler completes a command
while we are polling for completion in aha_cmd.
If timer calculation results in degenerate value (0), force it to 1
to avoid divide-by-zero panic later on in calls to IGMP_RANDOM_DELAY().
I considered simply adding 1 to the timer calculation, but was unsure
if the calculation was part of the IGMP standard or not so did not want
to mess with it for all cases.
Obtained from: Stephen Clawson <sclawson@cs.utah.edu>
Wakeup anyone waiting on a mount point prior to returning from umount,
whether an error occurs or not. Fixes a stat/NFS-umount race and other
potential future problems. Fix taken from bug/pr which also indicated
that the same fix has already been applied to OpenBSD and NetBSD.
This is odd, especially in the case of USB where the driver is found
in several tries: vendor specific, class specific, interface specific.
The mouse driver is found at the interface specific level...
Reviewed by: Doug Rabson (dfr@freebsd.org)
floppy is used on the toshiba Libretto line of subnotebook computers.
It differs from a normal floppy in that you must use PIO rather than
DMA to transfer the data.
To enable this, you must add options "FDC_YE" to your kernel. I don't
have a machine that has a floppy and a pcmcia slot to test to make
sure that this doesn't impact normal floppy units, so I've left this as
an option.
I have ported this to -current and made an attempt to ensure that the
indentation conforms to style(9), aka the bruce filter.
Reviewed by: nate, markm
Submitted by: David Horwitt (dhorwitt@ucsd.edu)
incorporate some notion of which revision the device is. If it's < SCSI2, for
example, READ BLOCK LIMITS is not a MANDATORY command.
At any rate, the initial state is to try and read block limits to get a notion
of the smallest and largest record size as well as the granularity. However,
this doesn't mean that the device should actually *in* fixed block mode should
the max && min be equal... *That* choice is (for now) determined by whether
the device comes up with a blocksize of nonzero. If so, then it's a fixed block
preferred device, otherwise not (this will change again soon).
When actually doing I/O, and you're in fixed length mode, the block count is
*not* the byte count divided by the minimum block size- it's the byte count
divided by the current blocksize (or use shift/mask shortcuts if that worked
out...).
Then when you *change* the blocksize via an ioctl, make sure this actually
propagates to the stored notion of blocksize (and update the shift/mask
shortcuts).
Misc Other:
When doing a mode select, only use the SCSI_SAME_DENSITY (0x7f) code if
the device is >= SCSI2- otherwise just use the saved density code.
Recover from the ripple of ILLEGAL REQUEST not being 'retried' in that
RESERVE/RELEASE is not a mandatory command for < SCSI2 (so ignore it if it
fails).
but the present PCI probe code still thinks we are there as the pci attach
can't return an error code.
This means we are in the shared interrupt list, but have not been set up.
If we are sharing ints with another device, ohci_intr will be called and will
coredump on a NULL reference. So just return if it is called when not set up.
This fixes the symptom and not the cause.
The right answer is to let the PCI system know that the attach failed,
or to fail earlier (in the PCI probe).
The attach() is a void fn() so it can't return failure..
If we are not transfering any data, use a non S/G ccb type that doesn't
return residual information. It seems that some firmware revisions dislike
S/G ccbs with 0 length S/G lists.
Correct bt_cmd() so that we always honor command status that was latched
by our interrupt routine while polling for completion..
programs using glibc expect edx to be preserved accross syscalls.
As a result, linux programs running in emulation mode can
have whatever value may be represented by edx clobbered.
PR: 9038
Submitted-By: Richard Seaman, Jr. <dick@tar.com>
is more robust and common code can be used for both the target and iniator
roles. The mechanism for tracking negotiation state has also been simplified.
Add support for sync/wide negotiation in target mode and fix many of
the target mode bugs running at higher speeds uncovered. Make a first
stab at getting all of the bus skew delays correct. Sync+Wide dataout
transfers still cause problems, but this may be an initiator problem.
Ensure that we exit BITBUCKET mode if the controller is restarted.
Add support for target mode only firmware downloads. This has been
tested on the aic7880, but should mean that we can perform target mode
on any aic7xxx controller. Mixed mode (initiator and target roles in
the same firmware load) is currently only supported on the aic7890, but
with optimization, may fit on chips with less instruction space.
Allow sync transfers if the controller supports it. Wide will follow
as soon as I get the kinks worked out of wide target transfers in the
aic7xxx driver (currently the only target mode driver in the tree).
to specify that it does not provide initiator services (PIM_NOINITIATOR)
and that the initial bus reset for device probing should be avoided
(PIM_NOBUSRESET).
Modify the XPT layer to honor these flags.
0. This makes it difficult to do efficient manipulation of the
struct pollfd since you can't leave a slot empty.
PR: 8599
Submitted-by: Marc Slemko <marcs@znep.com>
1) Removed 'emulation' of bitmaps in printfs, FreeBSD seems to have caught
up on that one
2) Fixed a few bugs in the timeout/timo timeout variables
3) First attempt at fixing a bug mentioned by Kazu: uhci_run is not able
start/stop his USB host on his motherboard.
that the generated files are generated before any of the object files.
Also minor cleanup of dependencies in conf/files that I bogusly added
before.
This should fix the requirement that make depend be done starting from
a clean config directory. If you don't have a clean directory, make
depend is still required if you want the proper .o's to be recompiled.
Reviewed by: bde
as a RealTek 8139
if_rlreg.h: use bus_space_read_X() in CSR_READ_X() macros instead of
directly calling inb()/outb() etc...
rl.4 + RELNOTES.TXT: mention that SMC EtherEZ PCI 1211-TX is supported
by the RealTek driver
apparently possible) event that the transmit start routine is
called with and empty if_snd queue, bail out instead of dereferencing
unilitialized transmit list pointers and panicking.
suggested compilation cleanups from Eklund. Wire down a hard loop id if we are
not on a platform that has the ability to get to a PCI BIOS (it still will
float to the ID it gets after a LIP but at least we can try). Clarify that the
expanded lun is based upon SCCLUN defines (in f/w).
for possible buffer overflow problems. Replaced most sprintf()'s
with snprintf(); for others cases, added terminating NUL bytes where
appropriate, replaced constants like "16" with sizeof(), etc.
These changes include several bug fixes, but most changes are for
maintainability's sake. Any instance where it wasn't "immediately
obvious" that a buffer overflow could not occur was made safer.
Reviewed by: Bruce Evans <bde@zeta.org.au>
Reviewed by: Matthew Dillon <dillon@apollo.backplane.com>
Reviewed by: Mike Spengler <mks@networkcs.com>
during a trek through RCS. The Macronix 98713 and 98713A both have the
same PCI device ID but different revision numbers, and we need to be
able to tell one from the other. The 98715 and 98715A chips have the
same device ID as the 98725 chip but different revision numbers, however
we lump them into the same category except when identifying them during
the PCI probe output.
The main reason we need tell the chips apart is that the Macronix app
notes say you have to write a special magic number into one of the
registers in order to put the chip in normal operating mode. The 98713
requires one magic value, while all the others require a different one.
PCI fast ethernet adapters, plus man pages.
if_pn.c: Netgear FA310TX model D1, LinkSys LNE100TX, Matrox FastNIC 10/100,
various other PNIC devices
if_mx.c: NDC Communications SOHOware SFA100 (Macronix 98713A), various
other boards based on the Macronix 98713, 98713A, 98715, 98715A
and 98725 chips
if_vr.c: D-Link DFE530-TX, other boards based on the VIA Rhine and
Rhine II chips (note: the D-Link and certain other cards
that actually use a Rhine II chip still return the PCI
device ID of the Rhine I. I don't know why, and it doesn't
really matter since the driver treats both chips the same
anyway.)
if_wb.c: Trendware TE100-PCIE and various other cards based on the
Winbond W89C840F chip (the Trendware card is identical to
the sample boards Winbond sent me, so who knows how many
clones there are running around)
All drivers include support for ifmedia, BPF and hardware multicast
filtering.
Also updated GENERIC, LINT, RELNOTES.TXT, userconfig and
sysinstall device list.
I also have a driver for the ASIX AX88140A in the works.
alpha, operations involving non-finite numbers or denormalised numbers
or operations which should generate such numbers will cause an arithmetic
exception. For programs which follow some strict code generation rules,
the kernel trap handler can then 'complete' the operation by emulating
the faulting instruction.
To use software completion, a program must be compiled with the arguments
'-mtrap-precision=i' and '-mfp-trap-mode=su' or '-mfp-trap-mode=sui'.
Programs compiled in this way can use non-finite and denormalised numbers
at the expense of slightly less efficient code generation of floating
point instructions. Programs not compiled with these options will receive
a SIGFPE signal when non-finite or denormalised numbers are used or
generated.
Reviewed by: John Polstra <jdp@polstra.com>
option not defined the sysctl int value is set to -1 and read-only.
#ifdef KERNEL's added appropriately to wall off visibility of kernel
routines from user code.
Add ICMP_BANDLIM option and 'net.inet.icmp.icmplim' sysctl. If option
is specified in kernel config, icmplim defaults to 100 pps. Setting it
to 0 will disable the feature. This feature limits ICMP error responses
for packets sent to bad tcp or udp ports, which does a lot to help the
machine handle network D.O.S. attacks.
The kernel will report packet rates that exceed the limit at a rate of
one kernel printf per second. There is one issue in regards to the
'tail end' of an attack... the kernel will not output the last report
until some unrelated and valid icmp error packet is return at some
point after the attack is over. This is a minor reporting issue only.
not like the 6-byte read and write commands! It returns illegal request,
with the field pointer pointing to byte 9 of a 6 byte CDB.
In any case, the work around is to put in a quirk mechanism that makes sure
that we don't send 6-byte reads or writes to this device. It's rather sad
that this is necessary. You'd think that they would be able to get
something that basic to work right in their firmware...
Reviewed by: gibbs
Reported by: Adam McDougall <bsdx@spawnet.com>
problem is worked around by using an interrupt gate for the page
fault handler. This code was originally made for NetBSD/pc98 by
Naofumi Honda <honda@kururu.math.sci.hokudai.ac.jp> and has already
been in PC98 tree. Because of this bug, trap_fatal cannot show
correct page fault address if %cr2 is obtained in this function.
Therefore, trap_fatal uses the value from trap() function.
- The trap handler always enables interruption when buggy application
or kernel code has disabled interrupts and then trapped. This code
was prepared by Bruce Evans <bde@FreeBSD.org>.
Submitted by: Bruce Evans <bde@FreeBSD.org>
Naofumi Honda <honda@kururu.math.sci.hokudai.ac.jp>
going to want a major number from that list instead. Also use the
same preallocated local range (500-600) for blkdevs as well as cdevs,
just to be orthogonal. The latter was for Brian, who has a *lot*
of local device drivers and needs more than just a single reserved
number.
can set if your hw/sw produces the "calcru negative..." message.
Setting the alternate method (sysctl -w kern.timecounter.method=1)
makes the the get{nano|micro}*() functions call the real thing at
resulting in a measurable but minor overhead.
I decided to NOT have the "calcru" change the method automatically
because you should be aware of this problem if you have it.
The problems currently seen, related to usleep and a few other corners
are fixed for both methods.
is completely empty. There is an interrupt for output completion. It
is painful to use, but polling method used in the corresponding fix in
sio.c (rev.1.152) can't be used because there is no status bit for
transmitter-empty. Now ttywait() works right.
Reminded by: NIST-PCTS
Don't call timeout() for DTR wakeup if the relevant timeout is already
active. This fixes "timeout table full" panics when sufficiently many
cyopen()s are interrupted while they are sleeping waiting for the
timeout to expire.
install all those images at all (nor to install them under /usr/mdec), given
the high degree of customization this Makefile needs in order to get images
that are actually useful for some NIC.
Submitted by: John Hay <jhay@mikom.csir.co.za>,
Paul Allenby <pallenby@mikom.csir.co.za>
runtime. p_runtime is unsigned while p_cpulimit is not, so this avoids the
nasty side effect of the process getting killed when the runtime comes up
"negative" due to other bugs.
