instead of 0 if there is no input.
syscons.c:
Added missing spl locking in sccncheckc(). Return the same value as
sccngetc() would. It is wrong for sccngetc() to return non-ASCII, but
stripping the non-ASCII bits doesn't help.
make it more intelligible, improve the partially bogus locking, and
allow for a ``quick re-acquiration'' from a pending release of timer 0
that happened ``recently'', so it was not processed yet by clkintr().
This latter modification now finally allows to play XBoing over
pcaudio without losing sounds or getting complaints. ;-) (XBoing
opens/writes/closes the sound device all over the day.)
Correct locking for sysbeep().
Extensively (:-) reviewed by: bde
Testing with the high frequency of 20000 Hz (to find problems) only found
the problem that this frequency is too high for slow i386's.
Disable interrupts while setting the timer frequency. This was unnecessary
before rev.1.57 and forgotten in rev.1.57. The critical (i8254) interrupts
are disabled in another way at boot time but not in the sysctl to change
the frequency.
enable flag instead of enable_intr() to restore it to its usual state.
getit() is only called from DELAY() so there is no point in optimising
its speed (this wasn't so clear when it was extern), and using
enable_intr() made it inconvenient to call DELAY() from probes that need
to run with interrupts disabled.
time. The results are currently ignored unless certain temporary options
are used.
Added sysctls to support reading and writing the clock frequency variables
(not the frequencies themselves). Writing is supposed to atomically
adjust all related variables.
machdep.c:
Fixed spelling of a function name in a comment so that I can log this
message which should have been with the previous commit.
Initialize `cpu_class' earlier so that it can be used in startrtclock()
instead of in calibrate_cyclecounter() (which no longer exists).
Removed range checking of `cpu'. It is always initialized to CPU_XXX
so it is less likely to be out of bounds than most variables.
clock.h:
Removed I586_CYCLECTR(). Use rdtsc() instead.
clock.c:
TIMER_FREQ is now a variable timer_freq that defaults to the old value of
TIMER_FREQ. #define'ing TIMER_FREQ should still work and may be the best
way of setting the frequency.
Calibration involves counting cycles while watching the RTC for one second.
This gives values correct to within (a few ppm) + (the innaccuracy of the
RTC) on my systems.
regarding apm to LINT
- Disabled the statistics clock on machines which have an APM BIOS and
have the options "APM_BROKEN_STATCLOCK" enabled (which is default
in GENERIC now)
- move around some of the code in clock.c dealing with the rtc to make
it more obvios the effects of disabling the statistics clock
Reviewed by: bde
Always delay using one inb(0x84) after each i/o in rtcin() - don't
do this conditional on the bogus option DUMMY_NOPS not being defined.
If you want an optionally slightly faster rtcin() again, then inline
it and use a better named option or sysctl variable. It only needs
to be fast in rtcintr().
clock interrupts.
Keep a 1-in-16 smoothed average of the length of each tick. If the
CPU speed is correctly diagnosed, this should give experienced users
enough information to figure out a more suitable value for `tick'.
variants, idea taken from NetBSD clock.c.
At least year calculation was wrong, pointed by Bruce.
Use different strategy to store year for BIOS without RTC_CENTURY
- Don't print out meaningless iCOMP numbers, those are for droids.
- Use a shorter wait to determine clock rate to avoid deficiencies
in DELAY().
- Use a fixed-point representation with 8 bits of fraction to store
the rate and rationalize the variable name. It would be
possible to use even more fraction if it turns out to be
worthwhile (I rather doubt it).
The question of source code arrangement remains unaddressed.
free-run and doing a subtract in microtime() rather than resetting the
counter to zero at every clock tick. In combination with the changes to
kern_clock.c, this should eliminate all the immediately obvious sources
of systematic jitter in timekeeping on Pentium machines.
to access it. setdelayed() actually ORs the bits in `idelayed' into
`ipending' and clears `idelayed'.
Call setdelayed() every (normal) clock tick to convert delayed
interrupts into pending ones.
Drivers can set bits in `idelayed' at any time to schedule an interrupt
at the next clock tick. This is more efficient than calling timeout().
Currently only software interrupts can be scheduled.
Put in the much shorter and cleaner version for the calibrate_cycle_counter
for the Pentium that Bruce suggested. Tested here on my Pentium and
it works okay.
shifting. Also correct the original code as Garrett noticed it in mail.
Leave the mishandled code in to use it later if future versions of gcc
are correct. The code was part of the calibrate_cyclecounter routine to
get the speed of the pentium chip.
Move definition of `stat_imask' to clock.c.
clock.c:
Rename `rtcmask' to `stat_imask' and export it. Rename `clkmask' to
`clk_imask' for consistency.
Only calculate TIMER_DIV(hz) once.
Merge debugging and "garbage" code to produce debugging code and format the
output better.
Make writertc() static inline and use it everywhere. Now all accesses to
the clock registers go through rtcin() and writertc().
Move rtc initialization to cpu_initclocks().
Merge enablertclock() with cpu_initclocks() and remove enablertclock().
The extra entry point was just a leftover from 1.1.5.
doesn't have to calculate it every call.
Rename `timer0_prescale' to `timer0_prescaler_count' and maintain it
correctly. Previously we lost a few 8253 cycles for every "prescaled"
clock interrupt, and the lossage grows rapidly at 16 KHz. Now we
only lose a few cycles for every standard clock interrupt.
Rename `*_divisor' to `*_max_count'.
Do the calculation of TIMER_DIV(rate) only once instead of 3 times each
time the rate is changed.
Don't allow preposterously large interrupt rates. Bug fixes elsewhere
should allow the system to survive rates that saturate the system, however.
Clean up declarations.
Include <machine/clock.h> to check our own declarations.
Changed the fifth parameter to register_intr() from u_int mask into
u_int *maskptr in preparation for new features (shared interrupts and
removable devices, eg. for PCMCIA).
