o relax some error handling so other drivers (e.g. ath) are usable
o revert ap scanning logic to old scheme
o add to capability info printing for 11a and 11g
nice distribution without significantly impacting interactive response.
As a side effect it should also allow batch processes to run for a
slightly longer period which will positively impact their performance.
This is based on the ubsa driver by Alexander Kabaev along with documentation
gleaned from the Linux mct_u232 driver. I've had this driver sitting in my
tree for almost 6 months, and several others have found it useful.
have completed across the bus but not to the host before
processing of an exception condition (busfree, bus reset,
etc.). When flushing the controller of completed commands,
we also look for packetized commands that have completed
with good status and are stored in the "good status fifo".
The hardware will post to the good status fifo even if
data for that command is still active in a FIFO. In
one particular failure case, a command outstanding on the
bus reconnected, transferred data into a FIFO, and provided
good status while the host driver was processing an expected
busfree event (PPR message negotiation). This resulted in
an entry in the good status fifo that we completed, but
since the sequencer was paused, the data in the data FIFO
for this command had never been transferred to the host.
Once the busfree processing was complete, the sequencer
was unpaused, and the data completed its transfer to the
host. In some instances, the client for the data was notified
of the completion and attempted to view the data before
it arrived. This case only occurred during FreeBSD's
multi-target probe of the SCSI bus while some devices are
negotiating to go packetized and some devices are already
running in packetized.
The fix is to run and FIFOs active with a context in the
good status fifo to completion before completing the command
to the SCSI layer. This requies duplicating the FIFO rundown
operations in the host driver that would usually be handled
by the firmware, but there is no other alternative.
Don't blindly shutdown the SCB dma engine when restarting
the sequencer. We may be killing an operation that is
not supposed to be cancelled. The cases where we need to
shutdown these dma engines are already handled elsewhere in
the driver.
Fix a few more ahd_in?() -> ahd_in?_scbram() instances.
Add softc flag to indicate that we have seen at
least one selection since the last bus reset or
SE/LVD bus change.
aic79xx.c:
Fix a few style nits.
In ahd_update_pending_scbs(), only touch card registers
once we have found an SCB that needs to be updated.
This removes lots of clutter from PCI traces taken of
error recovery performed by the driver.
Short circuit the first selection iocell workaround handler
if we've run once since the last bus reset or iocell change.
This also removes clutter from PCI traces.
Note if completions are pending in the qoutfifo when we dump
card state.
Add a comment in ahd_clear_critical_sections() about
our need to leave ENBUSFREE set in SIMODE1 while single
stepping.
Re-arrange some delay loops so that we always perform
a read after any register write and before the delay.
This should make the delay loop more accurate.
When completing message processing for a packetized
commention, return the controller to a state where
invalid non-packetized phases will still cause protocol
violations. These are the same operations as those
performed in the clear_target_state routine in the
firmware.
Now that we have a chip with working ABORTPENDING
support (the 7901B), comment out the automatic use
of this feature until we can adequately test it.
The previous checkin updated the bug mask for the
7901B so this code was exercised.
When resetting the bus, perform an ahd_flush_device_writes()
call so that our reset assertion delay is acurately
timed from when the reset bit is written to the controller.
Remove an old comment that no longer applies.
Fix a jump in our unexpected non-packetized phase
handler to use an explicit lable. The old code
had a hardcoded jump offset that was off by one
instruction.
Add a 7901A specific feature definition.
aic79xx_pci.c:
Split out the general aic790X setup into it's own
setup handler that works on single and dual controllers.
Adjust all other PCI setup handlers to initialize the
chips basic features and type before calling the generic
handler.
Turn off a few Rev B workarounds that are not required
on the 7901B.
to store an int in the bio->bio_driver1 (a void *). It is big enough,
but you have to match the int sizes first before doing the cast.
Glanced at by: scottl
mark crypto requests with ``callback immediately'' to avoid doing a context
switch to return crypto results. This completes the work to eliminate
context switches for using software crypto via the crypto subsystem (with
symmetric crypto ops).
software crypto device:
o record crypto device capabilities in each session id
o add a capability that indicates if the crypto driver operates synchronously
o tag the software crypto driver as operating synchronously
This commit also introduces crypto session id macros that cleanup their
construction and querying.
breakages. Note that runtime compatibility is not guaranteed. Future
changes to setjmp/longjmp in libc will break threaded applications
linked against libc_r.so.5 on ia64. We pull our "tier 2" card once
more...
Reviewed by: ru
an MSDOSFS file system either failed, silently corrupted the file, or
sometimes corrupted the neighboring file.
PR: 53695
Submitted by: Ariff Abdullah <skywizard@MyBSD.org.my> (original version)
MFC: 3 days
channel has been disabled by BIOS. This prevents a bus timeout
machine check on B&W G3 PowerMacs, which have a primary-only CMD646
on the motherboard.
Approved by: sos
Obtained from: NetBSD
bus_dma async callback scheme. Note that sparc64 does not seem to do
async callbacks. Note that ia64 callbacks might not be MPSAFE at the
moment. Note that powerpc doesn't seem to do async callbacks due to
the implementation being incomplete.
Reviewed by: mostly silence on arch@
obsolete. The intend is to add glue to either libthr or
libpthread to create the necessary compat links.
o Hook libpthread to the build on ia64. This is slightly out of
order, because the kernel still doesn't have all the support,
but that's not a problem in this case.
functions are derived from the swapctx() and restorectx() (resp)
from sys/ia64/ia64/context.s. The code is expected to be 99%
correct, but has not yet been tested.
Note that with these functions operating on mcontext_t, we also
created the foundation upon which we can implement getcontext(2)
and setcontext(2) replacements. It's not guaranteed that the use
of these syscalls and _ia64_{save|restore}_context() on the same
uicontext_t is actually going to work. Replacing the syscalls is
now trivially achieved.
This commit completes the ia64 port of libpthread itself (modulo
testing and bugfixes).
succeeds. There is a difference between how OLDCARD and NEWCARD deal
with their resources, and this code exposes that difference. I'm not
sure which behavior is correct, and will need to look into that in
more detail. However, it appears that we go ahead and allocate the
right thing in both cases that I have access to (CF cards, CDROM, and
external ata enclosures), so go ahead and ignore the failure to get
the resource for the other rid. There's already another check to make
sure that the actual allocation works correctly, and that should be
sufficient to catch cases that don't work.
Submitted by: wpaul and iedowse
