modes on a tty structure.
Both the ".init" and the current settings are initialized allowing
the function to be used both at attach and open time.
The function takes an argument to decide if echoing should be enabled.
Echoing should not be enabled for regular physical serial ports
unless they are consoles, in which case they should be configured
by ttyconsolemode() instead.
Use the new function throughout.
invalidate the TLB(s) if the old mapping wasn't used by the CPU. With
network interfaces that implement checksum off-loading, the old mapping is
almost never used by the CPU, only by the device driver for setting up the
DMA operation.
Reviewed by: tegge@
Restructure pmap_enter() to prevent the loss of a page modified (PG_M) bit
in a race between processors. (This restructuring assumes the newly atomic
pte_load_store() for correct operation.)
Reviewed by: tegge@
PR: i386/61852
RAM. Many older, legacy bridges only allow allocation from this
range. This only appies to devices who don't have their memory
assigned by the BIOS (since we allocate the ranges so assigned
exactly), so should have minimal impact.
Hoewver, for CardBus bridges (cbb), they rarely get the resources
allocated by the BIOS, and this patch helps them greatly. Typically
the 'bad Vcc' messages are caused by this problem.
that is no longer required. (In fact, it is not clear that it was ever
required in HEAD or RELENG_4, only RELENG_3 required a work-around.) Now,
as before revision 1.251, if the preexisting PTE is invalid, pmap_enter()
does not call pmap_invalidate_page() to update the TLB(s).
Note: Even with this change, the handling of a copy-on-write fault is
inefficient, in such cases pmap_enter() calls pmap_invalidate_page() twice.
Discussed with: bde@
PR: kern/16568
need to mask off the page offset bits. (This operation made some sense
prior to i386/i386/pmap.c revision 1.254 when we passed a physical address
rather than a vm_page pointer to pmap_enter().)
uses predate the change in the pmap_enter() interface that replaced the
page's physical address by the address of its vm_page structure. The
PHYS_TO_VM_PAGE() was being used to compute the address of the same vm_page
structure that was being passed in.
1. Process p1 is currently being swapped in.
2. Process p2 calls linux_ptrace(PTRACE_GETFPXREGS, p1_pid, ...)
3. After acquiring a reference to FIRST_THREAD_IN_PROC(p1),
p2 blocks in faultin() while p1 finishes being swapped in.
This means p2 won't get back the lock on p1 until after p1's
threads are runnable.
4. After p1 is swapped in, the first thread in p1 exits.
5. p2 now uses its dangling reference to p1's first thread.
pmap_copy(). This entails additional locking in pmap_copy() and the
addition of a "flags" parameter to the page table page allocator for
specifying whether it may sleep when memory is unavailable. (Already,
pmap_copy() checks the availability of memory, aborting if it is scarce.
In theory, another CPU could, however, allocate memory between
pmap_copy()'s check and the call to the page table page allocator,
causing the current thread to release its locks and sleep. This change
makes this scenario impossible.)
Reviewed by: tegge@
multiprocessors. Specifically, the error is conditioning the call to
pmap_invalidate_page() on whether the pmap is active on the current CPU.
This call must be unconditional. Regardless of whether the pmap is active
on the CPU performing _pmap_unwire_pte_hold(), it could be active on another
CPU. For example, a call to pmap_remove_all() by the page daemon could
result in a call to _pmap_unwire_pte_hold() with the pmap inactive on the
current CPU and active on another CPU. In such circumstances, failing to
call pmap_invalidate_page() results in a stale TLB entry on the other CPU
that still maps the now deallocated page table page. What happens next is
typically a mysterious panic in pmap_enter() by the other CPU, either
"pmap_enter: attempted pmap_enter on 4MB page" or "pmap_enter: pte vanished,
va: 0x%lx". Both occur because the former page table page has been recycled
and allocated to a new purpose. Consequently, it no longer contains zeroes.
See also Peter's i386/i386/pmap.c revision 1.448 and the related e-mail
thread last year.
Many thanks to the engineers at Sandvine for providing clear and concise
information until all of the pieces of the puzzle fell into place and
for testing an earlier patch.
MT5 Candidate
a stack trace from ddb, the output will pause with a '--More--' prompt
every 18 lines. If you hit Enter, it will print another line and prompt
again. If you hit space it will output another page and then prompt.
If you hit 'q' or 'x' it will abort the rest of the stack trace.
- Fix the sparc64 userland stack trace to honor the total count of lines
to print. This is useful if your trace happens to walk back onto
0xdeadc0de and gets stuck in an endless loop.
MFC after: 1 month
Tested on: i386, alpha, sparc64
the page table page's wired count rather than its hold count to contain
the reference count. My rationale for this change is based on several
factors:
1. The machine-independent and pmap layers used the same hold count field
in subtly different ways. The machine-independent layer uses the hold
count to implement a form of ephemeral wiring that is used by pipes,
physio, etc. In other words, subsystems where we wish to temporarily
block a page from being swapped out while it is mapped into the kernel's
address space. Such pages are never removed from the page queues.
Instead, the page daemon recognizes a non-zero hold count to mean "hands
off this page." In contrast, page table pages are never in the page
queues; they are wired from birth to death. The hold count was being
used as a kind of reference count, specifically, the number of valid
page table entries within the page. Not surprisingly, these two
different uses imply different synchronization rules: in the machine-
independent layer access to the hold count requires the page queues
lock; whereas in the pmap layer the pmap lock is required. Thus,
continued use by the pmap layer of vm_page_unhold(), which asserts that
the page queues lock is held, made no sense.
2. _pmap_unwire_pte_hold() was too forgiving in its handling of the wired
count. An unexpected wired count on a page table page was ignored and
the underlying page leaked.
3. In a word, microoptimization. Using the wired count exclusively, rather
than a combination of the wired and hold counts, makes the code slightly
smaller and faster.
Reviewed by: tegge@
not sure yet about 5.x... MFC if needed.
Also fixes small problems with examining some registers and
some specific gdb transfer problems.
As the patch says:
This is not a pretty patch and only meant as a temporary
fix until a better solution is committed.
PR: i386/71715
Submitted by: Stephan Uphoff <ups@tree.com>
MFC after: 1 week
and which takes a M_WAITOK/M_NOWAIT flag argument.
Add compatibility isa_dmainit() macro which whines loudly if
isa_dma_init() fails.
Problem uncovered by: tegge
the loss of a page modified (PG_M) bit in a race between processors.
Quoting Tor:
One scenario where the old code could cause a lost PG_M bit is a
multithreaded linux program (or FreeBSD program using the
linuxthreads port) where one thread was starting a subprocess.
The thread doing fork() would call vmspace_fork(), which would then
call vm_map_copy_entry() which would call pmap_protect() on an area
possibly accessed by other threads.
Additionally, make the clearing of PG_M by pmap_protect() unconditional if
write permission is removed. Previously, PG_M could persist on a read-only
unmanaged page. That seems inconsistent and confusing.
In collaboration with: tegge@
MT5 candidate
PR: 61852
fully initialed when the pmap layer tries to call sched_pini() early in the
boot and results in an quick panic. Use ke_pinned instead as was originally
done with Tor's patch.
Approved by: julian
value was only enough for 8GB of RAM, the new value can do 16GB. This still
isn't optimal since it doesn't scale. Fixing this for amd64 looks to be
fairly easy, but for i386 will be quite difficult.
Reviewed by: peter
scheduler specific extension to it. Put it in the extension as
the implimentation details of how the pinning is done needn't be visible
outside the scheduler.
Submitted by: tegge (of course!) (with changes)
MFC after: 3 days
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
across frames. Basically, if the current frame is for the
'dblfault_handler' function, then get the next %eip and %ebp values to use
from the original TSS of the thread that has the saved state when the
double fault triggered.
MFC after: 4 days
and was propagated to nearly every platform. The boundary of the child needs
to consider the boundary of the parent and pick the minimum of the two, not
the maximum. However, if either is 0 then pick the appropriate one.
This bug was exposed by a recent change to ATA, which should now be fixed by
this change. The alignment and maxsegsz tag attributes likely also need
a similar review in the near future.
This is a MT5 candidate.
Reviewed by: marcel
Submitted by: sos (in part)
It can be switched back once 5.3 is tested and released. Also turn on
PREEMPTION as many of the stability problems with it have been fixed.
MT5: 3 days.
but with slightly cleaned up interfaces.
The KSE structure has become the same as the "per thread scheduler
private data" structure. In order to not make the diffs too great
one is #defined as the other at this time.
The KSE (or td_sched) structure is now allocated per thread and has no
allocation code of its own.
Concurrency for a KSEGRP is now kept track of via a simple pair of counters
rather than using KSE structures as tokens.
Since the KSE structure is different in each scheduler, kern_switch.c
is now included at the end of each scheduler. Nothing outside the
scheduler knows the contents of the KSE (aka td_sched) structure.
The fields in the ksegrp structure that are to do with the scheduler's
queueing mechanisms are now moved to the kg_sched structure.
(per ksegrp scheduler private data structure). In other words how the
scheduler queues and keeps track of threads is no-one's business except
the scheduler's. This should allow people to write experimental
schedulers with completely different internal structuring.
A scheduler call sched_set_concurrency(kg, N) has been added that
notifies teh scheduler that no more than N threads from that ksegrp
should be allowed to be on concurrently scheduled. This is also
used to enforce 'fainess' at this time so that a ksegrp with
10000 threads can not swamp a the run queue and force out a process
with 1 thread, since the current code will not set the concurrency above
NCPU, and both schedulers will not allow more than that many
onto the system run queue at a time. Each scheduler should eventualy develop
their own methods to do this now that they are effectively separated.
Rejig libthr's kernel interface to follow the same code paths as
linkse for scope system threads. This has slightly hurt libthr's performance
but I will work to recover as much of it as I can.
Thread exit code has been cleaned up greatly.
exit and exec code now transitions a process back to
'standard non-threaded mode' before taking the next step.
Reviewed by: scottl, peter
MFC after: 1 week
FULL_PREEMPTION is defined. Add a runtime warning to ULE if PREEMPTION is
enabled (code inspired by the PREEMPTION warning in kern_switch.c). This
is a possible MT5 candidate.
