Lower (ISA) IRQs are working, but allowed mask is not set correctly.
Block both by default to allow HP BL465c G6 blade system to boot.
Reported by: Attila Nagy <bra@fsn.hu>
MFC after: 1 week
Although access to the flags to check/set OACTIVE is racy due to how
the default if_start() function works, this should remove any races
with read/modify/write between threads.
don't setup the avp mcast queue.
This is a bit annoying though - it turns out the mcast queue isn't
initialised for STA mode but it's then touched to see whether anything
is in it. That should be fixed in a subsequent commit.
Noticed by: gperez@entel.upc.edu
PR: kern/165895
After 8.0-RELEASE, iwi(4) doesn't send any data frames in infrastructure
mode.
Bacause of the condition `while (frm < efrm)', IEEE80211_VERIFY_LENGTH()
was checking item length beyond the ieee80211_frame region, and returned
from iwi_checkforqos() without setting flags, capinfo and associd.
In infrastructure mode associd is required, so this problem causes
discarding mbuf in ieee80211_start().
PR: kern/165819
Tested/Reviewed/Supported by: bschmidt and adrian
MFC after: 1 week
In a very noisy 2.4GHz environment (with HT/40 enabled, making it worse)
I saw the following occur:
* the air was considered "busy" a lot of the time;
* the cabq time is quite short due to staggered beacons being enabled;
* it just wasn't able to keep up TX'ing CABQ frames;
* .. and the cabq would swallow up all the TX ath_buf's.
This patch introduces a twiddle which allows the maximum cabq depth to be
set, forcing further frames to be dropped.
It defaults to the TX buffer count at the moment, so the default behaviour
isn't changed.
I've also started fleshing out a similar setup for the data path, so
it doesn't swallow up all the available TX buffers and preventing management
frames (such as ADDBA) out.
PR: kern/165895
frames with stations in power saving mode.
I'm not (yet) sure how to handle TX'ing aggregates frames to stations
that are in power saving mode, or whether that's even a feasible thing
to do. So in order to (mostly) not forget, leave a couple of comments
in the code.
The code presently assumes that the aggregation TID state for an ath_node
is locked not by the ath_node lock or a node+TID lock, but behind the
hardware queue said TID maps to. This assumption is going to be
incorrect for stations in power saving mode as we'll be TX'ing frames
on the multicast queue.
In any case, I'm afraid its a "later problem". :/
This function must be called with both the source and destination TXQs
locked or things will get hairy.
I added this as part of some debugging in a PR but it turned out to not
be the cause. I still think it's -correct- so, here it is.
the last buffer in the list.
The current behaviour (due to me, so pointy hat is firmly on my head here)
was incorrect - it was setting the link pointer to the last descriptor
of the _first_ buffer in the TXQ. Instead, it should have set it to the
last descriptor in the _last_ buffer in the TXQ.
This showed up as occasional TX stalls with frames in the TXQ but no
TX progress being made. Further inspection showed the TXQ looked like
it contained multiple "lists" of frames - there'd be a list of correct
frames, then a NULL link pointer, but there'd be a next buffer in the
list.
Since this code is only called upon an interface reset, it's likely
this only began showing up when I started doing stress testing
in environments which annoy the radios enough to cause lockups.
I've not yet any TX stalls with this patch applied.
PR: kern/165866
Expand pci_save_state and pci_restore_state to save more of
the config state for PCI Express and PCI-X devices. Various
writable control registers are present in PCI Express that
can potentially be lost over suspend/resume cycle.
This change is modeled after similar functionality in Linux.
Reviewed by: wlosh,jhb
MFC after: 1 month
all for platforms that only have 32-bit bus addresses. Second, remove
the 'tag_valid' flag from the softc. Instead, if we don't create a
tag in pci_attach_common(), just cache the value of our parent's tag
so that we always have a valid tag to return.
Winbond Super I/O chips.
With minor efforts it should be possible the extend the driver to support
further chips/revisions available from Winbond. In the simplest case
only new IDs need to be added, while different chipsets might require
their own function to enter extended function mode, etc.
Sponsored by: Sandvine Incorporated ULC (in 2011)
Reviewed by: emaste, brueffer
MFC after: 2 weeks
This lets specify whereabouts of the parent PHY for a given MAC node
(and get rid of ugly kludges in mge(4) and tsec(4)).
Obtained from: Semihalf
MFC after: 1 week
- pci_find_extcap() is repurposed to be used for fetching PCI-express
extended capabilities (PCIZ_* constants in <dev/pci/pcireg.h>).
- pci_find_htcap() can be used to locate a specific HyperTransport
capability (PCIM_HTCAP_* constants in <dev/pci/pcireg.h>).
- Cache the starting location of the PCI-express capability for PCI-express
devices in PCI device ivars.
and not asynchronously. This fixes problems related to USB system
suspend and resume. It is assumed that we are always allowed to sleep
from the device_suspend() method.
MFC after: 1 week
Submitted by: jkim
cards that should be handled by the mfi(4) driver.
The root of the problem is that the mpt(4) driver was masking off the
bottom bit of the PCI device ID when deciding which cards to attach to.
It appears that a number of the mpt(4) Fibre Channel cards had a LAN
variant whose PCI device ID was just one bit off from the FC card's device
ID. The FC cards were even and the LAN cards were odd.
The problem was that this pattern wasn't carried over on the SAS and
parallel SCSI mpt(4) cards. Luckily the SAS and parallel SCSI PCI device
IDs were either even numbers, or they would get masked to a supported
adjacent PCI device ID, and everything worked well.
Now LSI is using some of the odd-numbered PCI device IDs between the 3Gb
SAS device IDs for their new MegaRAID cards. This is causing the mpt(4)
driver to attach to the RAID cards instead of the mfi(4) driver.
The solution is to stop masking off the bottom bit of the device ID, and
explicitly list the PCI device IDs of all supported cards.
This change should be a no-op for mpt(4) hardware. The only intended
functional change is that for the 929X, the is_fc variable gets set. It
wasn't being set previously, but needs to be because the 929X is a Fibre
Channel card.
Reported by: Kashyap Desai <Kashyap.Desai@lsi.com>
MFC After: 3 days
The tag enforces a single restriction that all DMA transactions must not
cross a 4GB boundary. Note that while this restriction technically only
applies to PCI-express, this change applies it to all PCI devices as it
is simpler to implement that way and errs on the side of caution.
- Add a softc structure for PCI bus devices to hold the bus_dma tag and
a new pci_attach_common() routine that performs actions common to the
attach phase of all PCI bus drivers. Right now this only consists of
a bootverbose printf and the allocate of a bus_dma tag if necessary.
- Adjust all PCI bus drivers to allocate a PCI bus softc and to call
pci_attach_common() from their attach routines.
MFC after: 2 weeks
interface supported by mvs(4) are 88SX, while AHCI-like chips are 88SE.
PR: kern/165271
Submitted by: Jia-Shiun Li <jiashiun@gmail.com>
MFC after: 1 week
clients.
These are helful when making certain drivers work on both Linux
and FreeBSD without changing the code flow too much.
Reviewed by: kib, wlosh
MFC after: 1 month
pci_cfg_save() and pci_cfg_restore() for device drivers to use when
saving and restoring state (e.g. to handle device-specific resets).
Reviewed by: imp
MFC after: 2 weeks
corruption. Thanks to scottl@ for the suggestion.
This change will likely be revised after consideration of a general
method to address this type of issue for other drivers.
Sponsored by: Sandvine Incorporated
MFC after: 3 days
extract a link status of PHY when parent driver is re(4).
RGEPHY_MII_SSR register does not seem to report correct PHY status
on some integrated PHYs used with re(4).
Unfortunately, RealTek PHYs have no additional information to
differentiate integrated PHYs from external ones so relying on PHY
model number is not enough to know that. However, it seems
RGEPHY_MII_SSR register exists for external RealTek PHYs so
checking parent driver would be good indication to know which PHY
was used. In other words, for non-re(4) controllers, the PHY is
external one and its revision number is greater than or equal to 2.
This change fixes intermittent link UP/DOWN messages reported on
RTL8169 controller.
Also, mii_attach(9) is tried after setting interface name since
rgephy(4) have to know parent driver name.
PR: kern/165509
